Advertisement
Electrical connection
ffyour house has aluminum w,[dng, see
"Electrical requirements", Page 2.
Electrical 8hock Hazard
Turn power supply off before connecting wires.
Use 8 gauge solid copper wire.
Electrically ground range.
Failure to follow these instructions can result
in death, fire, or electrical shock.
TMs oven [s manufactured with white (neutral}
power supply wire and a cabinet-connected bare
grounding wire twisted together.
Feed oven came through opening [n
the cabinet. Make electrical connection
following the steps needed for your installation.
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven came to junction box through the
U.L.q[sted conduit connector.
4. Connect the two Mack wires together with
twist-on connectors.
5. Connect the two red wires together with
twistoon connectors.
6. Complete electrical connection according to
local codes and ordinances.
3-wire cable from
power supply
black
es
white
wire
white
and
bare or green
wires
U,L,-listed
cable from
conduit
Figure 1
oven
connector
If local codes permit
connecting
cabinet-grounding
conductor to neutral white
wire in junction
box:
7. Connect the bare or green and
wMte oven cable wires to the
neutral (white) wire in junction
box. See Figure 1.
8. Replace junction box cover.
4-wire cable from
iunction
power supply"
Figure 2
cable from
connector
oven
If local codes do not permit
connecting
cabinet=grounding
conductor
to neutral white
wire in junction
box:
7. Connect white oven came wire to
neutral (white) wire [n junction
box. See Figure 2.
8. Connect the bare or green
grounding oven cable wire to a
grounded wire in the junction
box. See Figure 2.
9. Replace junction box cover.
if connecting
to a
four-wire electrical system:
7. Connect white oven came wire
to neutral (white) wire in
junction box. See Figure 2.
8. Connect the bare or green
grounding oven cable wire to
the green grounding wire in
junction box. Do not connect
bare or green grounding wire to
neutral (white) wire in junction
box. See Figure 2.
9. Replace junction box cover.
Attachment
Push against seal area of oven front frame
when pushing oven into cabinet.
Do not push against outside edges.
5_
Lift oven into cabinet cutout usmg the
oven opening as an area to grip.
shipping
foot
Push against seal area of front frame to push
oven into cabinet until shipping
feet almost
contact cabinet. Use a Phillips screwdriver
to
remove screws attaching
shipping
feet. Remove
and discard shipping
feet.
Push oven completely
into cabinet and center
oven in cabinet cutout.
screws
6u
iMPORTANT: Securely fasten oven to cabinet
using the two screws provided, insert the screws
through holes in mounting rails.
Slide top
of trim up
Pushtrim
into place.
Replace
trim screw
/
7m
Slide top end of each trim upward onto oven
side rails. Push each trim into place at bottom of
trim. Use screws to attach each trim to oven. Take
care not to scratch other surfaces with ends of trim.
8u
Replace oven racks.
9m
Reinstall the oven door by inserting ends
of hinges into hinge slots [n the oven frame. Push
hinges in as far as they will go. Open the door
(you will feel the door drop into place) and rotate
both hinge latches back to the locked position.
Close and open the door to check that the door
doses and opens completely. [f door does not
close or open completely, repeat the door
removal step and reinstall door as described
above.
Check operation
Turn on power supply. The display
pane[ will light up briefly. "PF" should appear [n
the temperature display.
the display. Press the "START" pad. Make sure the
oven door is closed and the "ON" light is shown in
the display area. After 2 minutes, partially open
oven door. You should feel heat from the oven.
Press the "CANCEL" pad.
If your oven does not heat or an "F", followed by a
number, appears in the display, contact your dealer
or check the "If you need service..." section of this
installation instructions.
To get the most efficient use
from your new oven, read your
Use and Care Guide. Keep Installation
Instructions
and Guide close to oven
for easy reference.
Page 3
Advertisement
