Advertisement
Table of Contents
Before you start,,,
Your safety and the safety of
others are very important.
We have provided many important
safety messages in this manual and
on your appliance. AK_'ays read and
obey all safety messages.
This is the safety alert
symbol.
This symbol alerts you to
potential hazards that can kill or hurt
you and others.
All safety messages will follow the
safety alert symbol and either the
word "DANGER" or "VVARNING".
These words mean:
You can be killed or seriously
injured if you don't immediately
follow instructions.
You can be killed or seriously
injured if you don't foltow
instructions.
All safety messages will tell you
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
IMPORTANT: Observe all governing
codes and ordinances.
WARNING:
If the
information
in this manua_
is not followed
exactly,
a
fire or explosion
may result
causing
property
damage,
persona_
injury
or death.
m Do not store
or use
gasoline
or other
flammable
vapors
and
_iquids in the vicinity
of
this or any other
appliance.
WHAT TO DO _FYOU
SMELL
GAS
o Do not try to _ight any
appliance.
o Do not touch
any
electrica_
switch.
o Do not use any phone
in
your
building.
o _mmediately
cal_ your
gas supplier
from
a
neighbor's
phone.
Follow
the gas supp_ier's
instructions.
o _f you cannot
reach your
gas supplier,
call the fire
department.
Installation
and service
must be performed
by a
qualified
installer, service
agency
or the gas
supplier.
NOTE: The range cooktop is
manufactured for use with Natural gas. To
convert to LR/Propane gas, see the Gas
Conversion instructions provided in
literature package.
Proper gas and electrical supply
connections must be available. See "Gas
supply requirements," Page 4 and
"Electrical requirements," Page 5.
IMPORTANT: Observe all governing
codes and ordinances.
Do not obstruct flow of combustion and
ventilation air.
Proper installation is your responsibility.
Have a qualified technician install this
range. Make sure you have everything
necessary for correct installation. It is the
installer's responsibility to comply with the
installation clearances specified on the
gas information label. The gas information
label and model/serial rating plate are
located on the surface below the control
panel.
This installation must conform with all
local codes and ordinances, in the
absence of local codes, installation must
conform with American National
Standard, National Fuel Gas Code ANSI
Z223.1 --latest
edition* or CAN/CGA --
B149 -- latest edition* installation codes=
it is the customer's responsibility:
o To contact a qualified electrical installer.
• To assure that electrical installation is
adequate and in conformance with
National Electrical Code, ANSI/NFPA
70 -- latest edition**, or CSA Standard,
C22.! Canadian Electrical Code, Part 1
-- latest edition*, and all local codes
and ordinances.
Cabinet opening dimensions shown must
be used. Given dimensions are minimum
clearances=
When installing a range under existing
cabinets and installation does not meet
the minimum cabinet clearances, install a
range hood above the range to avoid burn
hazards.
NOTE: Some cabinet and building
materials are not designed to withstand
the heat produced by the oven for baking
and self-cleaning. Check with your builder
or cabinet supplier to make sure that the
materials used will not discolor,
delaminate or sustain other damage.
All openings in the wall or floor where the
range is to be installed must be sealed.
it is recommended that a range hood be
installed above this range.
Copies of the standards listed may be obtained
from:
* CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
** National Fire Protection Association
One Batterymarch
Park
Quincy, Massachusetts
02269
- Quick Links:
- Before You Start
- Natural Gas
- Home Appliances
Hide quick links:
Advertisement
Table of Contents
