Location Requirements - KitchenAid KWCU480WSS0 Installation Instructions Manual

36" (91.4 cm) and 48" (121.9 cm) designer commercial-style wall-mount canopy range hood
Table of Contents

Advertisement

Available languages

Available languages

Partsneeded
• Home power supply c able
• 1 -1/2" (12.7 mm) U Llisted orCSA approved strain relief
• 2 ULlisted wireconnectors
• 1wall o rroofcap
• Metal vent s ystem
• 2 -250-watt max heat l amp bulbs
Parts supplied
Remove parts from packages. Check that all parts are included.
3 metal grease filters for 36" (91.4 cm) models
4 metal grease filters for 48" (121.9 cm) models
10 - #10 Phillips head mounting screws for 36" (91.4 cm)
models
12 - #10 Phillips head mounting screws for 48" (121.9 cm)
models
4 - washer head screws
4- flat head screws
4-"L"
brackets
Lower chimney cover
Upper chimney cover
Damper (2 for 48" [121.9 cm] model)
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial
rating
plate is located inside the range hood on the rear wall of the
range hood.
Canopy range hood location should be away from strong draft
areas, such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions
provide minimum clearance.
The canopy range hood is factory set for venting through the roof
or through the wall.
All openings in ceiling and wall where canopy range hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities
and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product Dimensions
Vented Installations
147/8'' (37.8
cm) "/'_
_'_-
247/8-
37"
211/4"
(94,0 cm)
(54.0 cm)
max,
77/8'' (20.0
cm)
/
25"
(63,5
cm)
Installation Dimensions
36" (91.4 crn) or 48" (121.9 crn)
or cabinet
opening
width
(if installed between
cabinets)
¢-
-I
)
(
)
)
See Note*
18" (45.7 crn) rnin.
clearance
upper
cabinet
to countertop
36" (91.4 crn)
countertop
height
*NOTE: The range hood chimneys are adjustable and designed
to meet varying ceiling or soffit heights depending on the
distance "X" between the bottom of the range hood and the
cooking surface. For higher ceilings, a 39" (99.1 cm) Chimney
Extension Kit Part Number W10197714 (Stainless Steel), is
available from your dealer or an authorized parts distributor. The
chimney extension replaces the upper chimney shipped with the
range hood.
IMPORTANT:
Minimum distance "X": 30" (76.2 cm)
Suggested maximum distance "X": 36" (91.4 cm)
For vented installations, the chimneys can be adjusted for
ceilings between 8' 4W' (2.55 m) and 9' 3W' (2.83 m).

Advertisement

Table of Contents
loading

This manual is also suitable for:

Kwcu460ws00

Table of Contents