Advertisement
Available languages
Available languages
Installation
Requirements
Tools
and Parts
Gather the required
tools and parts before starting
installation.
All installations
Tools needed:
. Pliers
. Phillips screwdriver
. sA_"and 1/4" nut drivers or
hex sockets
. Measuring
tape or ruler
. 10" adjustable
wrench that
opens to 11/8 '' (2.9 cm)
. Flat-blade
screwdriver
. Utility
knife
.2 twist-on
wire connectors
which are the proper size
to connect your household
wiring to 16-gauge wiring
in dishwasher
. Small level
. Flashlight
. Shallow
pan
, %" open-end
wrench
, Bath towel
, Wood
block
, Torx®t T15 screwdriver
3/32"drill bit
3A6" hex-head
socket
Parts needed:
90 ° elbow with 3/s" N.RT.
external
threads on one
end. (The other end must
fit your water supply
line.)
Teflon ® tape or pipe joint
compound
Shims (if installed
with
built-up
floor)
Handle (not included)
Custom front panel
In addition,
for new installations
Tools needed:
. Cordless
drill with 1/2",3/4"
and 11/2 '' hole saw bits
. Small tubing cutter
. Wire stripper
. 11/2"-2 '' (6- 8 cm) screw-
type clamp if connecting
to waste-tee
Parts needed:
* Copper tubing (3/8"
recommended)
or flexible
stainless
steel braided fill
line
* Clamp connector
or strain
relief to fit a 7/8" (2.2 cm)
diameter
hole
Parts supplied:
A. Drain hose clamps
(2), 1 large and 1 small
B. # 10 x 1/2"Phillips-head
screws (2)
C. Drain hose
C
B
Make sure all these parts are included.
If not included,
call
1-800-4MY-HOME.
See separate
parts list for accessories
available
for your
dishwasher.
Location Requirements
Do not run drain lines, water lines or electrical
wiring
where they can interfere
with or contact dishwasher
motor
or legs.
The location
where the dishwasher
will be installed
must
provide cJearance between
motor
and flooring.
Motor
should
not touch the floor.
Do not install dishwasher
over carpeted flooring.
Shelter
dishwasher
and water lines leading to dishwasher
against freezing.
Damage from freezing
is not covered
by
the warranty.
A side panel kit is available
from your dealer for installing
your dishwasher
at the end of your cabinetry.
A moisture
barrier accessory
(Part Number
4396277) is
available
from your dealer for installing
underneath
the
countertop.
This may also be obtained
by calling
1-800-4MY-HOME.
Check location
where dishwasher
will be installed.
The
location
must provide:
easy access to water, electricity
and drain.
convenient
access for loading and unloading
dishes.
Corner
locations
require a 2" (5.1 cm) minimum
clearance
between the side of the dishwasher
door and the wall or
cabinet.
square opening
for proper operation
and appearance.
cabinet front perpendicular
to floor.
level floor. (If floor at front of opening
is not level with
floor at rear of opening,
shims may be needed to level
dishwasher.)
NOTE: To avoid shifting
during dishwasher
operation,
shims must be securely
attached to the floor.
If dishwasher
will be left unused for a period of time or in
a location
where it may be subject to freezing,
have it
winterized
by authorized
service personnel.
Make sure pipes, wires and drain hose are within
the
shaded area shown
in the "Cutout
dimensions"
section.
Helpful Tip: If the floor
in the dishwasher
opening
is
uneven (example:
tile flooring
only partway
into
opening)
you will need to pay attention
to measuring
dimensions
and leveling
the dishwasher.
t® TORX
is a registered
trademark
of Acument
Intellectual
Properties,
LLC
3
Advertisement
