Location Requirements - Kenmore 11021302012 Installation Instructions Manual

Partsneeded: ( Not s upplied w ithwasher)
Inlet h oses w ith
flatwashers
Toorder, please r efer t otoll-free p hone n umbers onback page
ofyourUse and Care Guide.
[] 8212656RP 10ft.(3.0 m)inlet h ose, B lack EPDM (2pack)
[] 8212641RP 5ft.(1.5 m)Inlet h ose, B lack EPDM (2pack)
[] 8212546RP 4ft.(1.2 m)Inlet h ose, B lack EPDM (2pack)
[] 8212545RP 5ft.(1.5 m)Inlet h ose, R ed andBlue EPDM
(2pack)
[] 8212487RP 5ft.(1.5 m)Nylon braided i nlet h ose (2pack)
[] 8212638RP 6ft.(1.8 m)Nylon braided i nlet h ose, space
saving 9 0 ° elbow, hypro-blue steel c ouplings
(2pack)
[] 8212637RP 6ft.(1.8 m)Inlet h ose, B lack EPDM, space
saving 9 0 ° elbow, hypro-blue steel c ouplings
(2pack)
Alternateparts:(Not s upplied withwasher)
Your i nstallation may require a dditional parts. Toorder, please
refer t otoll-free n umbers onback page ofyourUse and Care
Guide.
If you have:
Overhead sewer
1" (25 mm) standpipe
You will need:
Standard 20 gal. (76 L) 39" (990 mm)
tall drain tub or utility sink, sump
pump and connectors (available from
local plumbing suppliers)
2" (51 mm) diameter to 1" (25 mm)
diameter Standpipe Adapter
Part Number 3363920
Connector Kit Part Number 285835
Drain hose too short Extension Drain Hose Part
Number 285863
Connector Kit Part Number 285835
Lint clogged drain
Drain Protector Part Number 367031
Connector Kit Part Number 285835
LOCATmON REQUIREMENTS
Select proper location for your washer to improve performance
and minimize noise and possible "washer walk", install your
washer in a basement, laundry room, closet, or recessed area.
You will need:
[] A water heater set to 120 ° F (49° C).
[] A grounded electrical outlet located within 4 ft (1.2 m) of
power cord on back of washer.
[] Hot and cold water faucets located within 3 ft (0.9 m) of hot
and cold water fill valves on washer, and water pressure
of 20-100 psi (138-690 kPa).
[] A level floor with maximum slope of 1" (25 mm) under entire
washer, installing on carpet is not recommended.
[] Floor must support washer's total weight (with water and load)
of 315 Ibs (143 kgs).
iMPORTANT: Do not install, store, or operate washer where it will
be exposed to weather or in temperatures below 32 ° F (0° C).
Water remaining in washer after use may cause damage in low
temperatures. See "Washer Care" in your Use and Care Guide
for winterizing information.
Proper installation is your responsibility.
Recessed area or closet installation
3 mn
{76 turn)
n _ 1
i i
n i
n 1
i i
n 1
i
i
14" max. i
i i
{356 ram) .... j___
_mn i t i
{126 m _\ I
{25 rnrn)
{432 ram)
1 ml
{25 ram}
48 in.2
(310 cm 2}
24 in.2
(155cm_)
{76 ram)
Dimensions show recommended spacing allowed, except for
closet door ventilation openings which are minimum required.
This washer has been tested for installation with spacing of 0"
(0 mm) clearance on the sides. Consider allowing more space
for ease of installation and servicing, and spacing for companion
appliances and clearances for walls, doors, and floor moldings.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or Iouvered door is installed, top
and bottom air openings in door are required.
42"
{1067 ram)
L