Download Print this page

Advertisement

Eeotro fringe
installation manual
ENGLISH
the possibilities
Thank you for purchasing this Samsung produc_.
To receive more complete service, please register
your product a_
www.samsung.com/register
1-800-SAMSUNG(726-7864_
(_
100%
\
Recycled Pap_j
o
This manua_
_s maae
with 1 00 _o recyc_eo
paper.
Installation-USA
DG68-00108E-01_EN.indd
1
2011-03-18
_u4:06:26

Advertisement

   Also See for Samsung FTQ386

   Related Manuals for Samsung FTQ386

   Summary of Contents for Samsung FTQ386

  • Page 1

    Eeotro fringe installation manual ENGLISH the possibilities Thank you for purchasing this Samsung produc_. To receive more complete service, please register your product a_ www.samsung.com/register 1-800-SAMSUNG(726-7864_ 100% Recycled Pap_j This manua_ _s maae with 1 00 _o recyc_eo paper. Installation-USA DG68-00108E-01_EN.indd...

  • Page 2

    ABOUT THIS MANUAL READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. Important note to the installer Read all instructions contained in these installation instructions before installing range. Remove all packing materials from the oven compartments before connecting the electrical supply to the range. * Observe all governing codes and ordinances.

  • Page 3

    REMOVE PACKAGING Remove packaging materials. Failure to remove packaging materials could result in damage to the appliance. PREPARE TOOLS & PARTS What tools you will need Pliers 1/4"Nut Driver Drill Adjustable Wrench Flat Screwdriver Pencil Level Phillips Screwdriver What's included with your range Template Anti-Tip Bracket Screws (2 ea)

  • Page 4

    CHECKING THE iNSTALLATiON SiTE Clearances and dimensions To install the range, refer to the following figure. For installation in CANADA, a Free-standing range is not to be installed closer than 12ram from any adjacent surface, i_k__CAU'_'_0N This range has been designed to comply with the maximum allowable wood OAUTION cabinet temperatures of 194°F.

  • Page 5

    STEP 1. MEETING ELECTRICAL CONNECTION REQUIREMENTS CAUTION For persona, safety, do not use a n extension cord with t his a pp,iance. Remove house fuse or open circuit breaker before beginning installation. This appliance must be supplied with the proper voltage and frequency, and connected to an individual properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as specified on the rating plate.

  • Page 6

    STEP 2. ACCESSING THE POWER CORD CONNECTION Remove the rear access cover and loosen the screw with a screwdriver. The terminal block will then be accessible. Terminal block Access cover Specified power-supply-cord kit rating Diameter (inches) of range Range rating, watts Specified rating of connection opening power-supply-cord kit,...

  • Page 7

    STEP 3. INSTALLING THE POWER CORD For power cord installations, hook the strain relief over the power cord hole (lS/s") located below the rear of the drawer body. Insert the power cord through the strain relief and tighten the device..JJ ..

  • Page 8

    Installing a 4_wire power cord Aw_._._,_G WARNIN6 The neutral wire of the supply circuit must be connected to the neutral terminal located in the lower center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block.

  • Page 9

    STEP 4. INSTALLING THE CONDUIT Remove the conduit connection plate from the rear of the drawer body and rotate it as shown below. The conduit hole (11/8")must be used. 1. Prepare the conduit cord shown in Figure 1. 2. Install the conduit cord as shown in Figure 2. Figure 1 Figure 2 1"...

  • Page 10

    Installing a 4-wire conduit + Aluminum building wire may be used but it must be rated for the correct amperage and voltage to make the connection. Connect wires according to this Step 4 depending on the number of wires. + Wire used, location and enclosure of splices, etc., must conform to good wiring practices and local codes.

  • Page 11

    na the ranae INSTALLING THE ANTI-TIP DEVICE A__ W ARNING To reduce the risk of tipping, the appliance must be secured by properly WARNING installing the Anti-Tip device packed with the appliance. Refer to the installation instructions supplied with the bracket. Unless properly installed, the range could be tipped by stepping or sitting on the door.

  • Page 12

    3. Check your adjustments Use a spirit level to check your adjustments. Place the level diagonally on the oven rack, and check each direction for level. 1. Check direction 1. 2. Check direction 2. If the spirit level doesn't show level on the rack, adjust the leveling legs with a wrench.

Comments to this Manuals

Symbols: 0
Latest comments: