Install The Water Inlet Hose - Haier HWM75-0528 A User Manual

Install the water inlet hose

Confirm the water faucet
Water faucet,suitable
Outlet end surface
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen the
four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise
it may leak water. See to Figure 3.)
water inlet hose jointer
Slider
Screw knife
Lock level
water inlet hose
Figure 1
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
Figure 4
Water faucet,not suitable
Screw
Sign plate
Bushing
Figure 2 Figure 3
About 4mm before twisting
About less than 2mm after twisting
Screw nut
Figure 5
Figure 6
Reserve,Process,remain time digitron
It displays "--" during detecting.
It displays remained reserve time (hour).
It displays total remained time (min). If the total time
exceeds 99 minutes, it uses "A" on tens digit to
represent100 minutes, and uses "b" to represent 110
minutes.E.g. "A3" represents 103 minutes.
It displays abnormal symbol in abnormal situation.
(See to Page15)
(MINUTES)
WATER
LEVEL Digital display Digital display Digital display Digital display Digital display Digital display Digital display Digital display
(HOURS LATER)
Fuzzy logic control Fuzzy logic control Fuzzy logic control Fuzzy logic control Fuzzy logic control Fuzzy logic control Fuzzy logic control Fuzzy logic control
10 water level selection 10 water level selection 10 water level selection 10 water level selection 10 water level selection 10 water level selection 10 water level selection 10 water level selection
PROGRAM/RESERVE
WATER LEVEL button
PROGRAM/RESERVE button
The washing machine can detect the laundries automatically.
Push down the program/ reserve button. You
After detection,it will set the water level to suitable value among
can select one program of ten which is
4, 6, 8,and 10 automatically.
standard,soak heavy, gentle,save,cotton,
You can also set water level by yourself. After the machine is started,
single wash,rinse spin,single spin,tub clean, it will not set water level automatically. You shall push thestart/pause
button to make new setting.
air dry;
If there's water inside the tub, the machine cannot detect the
Push the"p rogram/ reserve " button to set the
laundries and will display water level 6 .
reserve wash program morethan two seconds
If save program is selected, it will display water level 2 .
continuously;
When water level 2 is reached in water filling, it will perform
When the "reserve" function is activated, the
washing while filling water.When water level 3 is reached, it will
indicator light of the program you have set will
change to normal washing.
be off. The "reserve (hour)" and "time remain"
During operation of wash and rinse program, you can push down
the water level button to add water. When you release the button, or
indicator lights will be on;
it reaches the overflow water level, the machine will stop adding
During reserve procedure, push the "reserve"
water.
button to display the reserve mode.To change
The water level decided may be different from actual value because
the running program or cancel the reserve
of the different moisture level of the laundries.
setting, you need to switch off the power and
Attention
make new selection;
"Power" button
Push the "power" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "power" button to switch on the power. If the
"start/pause" button is not pushed, the machine will
switch off the power automatically after 5 minutes.
POWER
ON/OFF
As selecting the water level 1,3,5,7,9;the light
is flashing;
As selecting the water level 2,4,6,8,10;the light
is lighting;