Advertisement
Safety precautions
Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
Earth
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,please wipe with
dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or the after-sale service department.
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
T h e v e n t i l a t i o n
holes at the bottom
Back
Soft object
Front
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
2
The washing machine must be positioned
so that the plug is accessible. Be sure to pull the
plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
c l e a n i n g t h e m a c h i n e . D o n o t p l u g
or pull the power plug with wet hand.
Do not use water hotter than 50 .
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.
Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department
or after-sale service department of our company. Do not repair it by yourself.
Phenomena
The reason
The digitron displays E0.
The top lid is opened during reserve procedure.
The drainage cannot work, or is too slow.
Is the drain hose put down?
The digitron displays E1.
Is the drain hose blocked?
It stops running in midway. The digitron
The top lid is not closed.
displays E2.
Are the laundries put slantingly?
The safety switch acts, and the
spinning cannot work. The
Is the machine slanting?
digitron displays E3.
Is the water tap opened, or is there water
The water filling does not work, or is
supply failure?
slow. After about 30 minutes later,
Is the water inlet valve blocked?
the digital displays E4.
Is the water pressure too low?
The digitron displays E6.
The water level sensor is bad.
Is there power failure?
Not wash
Is the power plug inserted tightly?
Is the water level reached preset position?
The machine does
not act
Is the power plug inserted tightly?
Not spin
Is the top lid closed reliably?
Are the laundries set flat?
Is the machine slanting?
There's abnormal sound inside
Are the laundries put slantingly in spinning?
the machine
Are there any foreign materials?
Is the screw of the jointer of water
The water tap leaks
inlet hose loose or awry?
Common phenomena
Phenomena
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The cloth sensor is checking the cloth, it willadd waterafter 48 seconds.
The wash procedure is paused.
The program is setting the drain time. Some time is needed
Push the PROGRAM button to select SPIN,
but it doesn't work.
before it starts spinning.
The pulsator pauses during water inlet
It is to avoid splashing during water inlet.
in wash and rinse.
There may be some water flowing out of the
It is the water remained in the factory inspection of performance.
drain hose in the first use of the machine.
How to settle
Close the top lid.
Put down the drain hose. Open and close the top lid once.
Clean the foreign material. Open and close The top Lid Once.
Close the top lid.
Reorder the laundries.Close the top lid.
The machine will start running after 10
seconds of being placed horizontally.
Open the water tap. Push the start/Pause button
once.
Clean the water inlet valve then push
the start/Pause button once.
Push the Start/Pause button once.
Please contact the after-sales
service department.
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Fasten the screw of the jointer properly.
Explanation
Advertisement
