Download Print this page
GE DPSE592GA1AA Installation Instructions Manual
GE DPSE592GA1AA Installation Instructions Manual

GE DPSE592GA1AA Installation Instructions Manual

Advertisement

Quick Links

BEFORE YOU BEGIN
Read
these
instructions
compLeteLy
and
c&re_[]yo
I M P O RTANT
- Save these
instructions
for local inspector's
use.
IMPORTANT
- Ohservea.
governing
codes and ordinances.
Note to Installer
- Be sure to leave these instructions with
the customer.
Note to Customer
Keep these instructions
with your Use
and Care Book fbr flmlre refi_rence.
This dryer must be exhausted to the outdoors.
Before the old dryer is removed
from service or discarded,
remove the dryer door.
Service Information
and the wiring diagram are located in
the control console.
Do not allow children on or in the appliance.
Close
supervision
of chiklren is necessary when the appliance is
used near chiklren.
TOOLS YOU WILL NEED
10" A DJUSTABLE
WRENCHES
{2)
SLIP JOINT PLIERS
FLAT BLADE SCREWDRIVER
8"PIPE WRENDHE
%
LEVEL
FOR YOUR SAFETY:
A
, Use only rigid metal or flexible metal 4-in. diameter
ductwork for exhausting
to the outdoors. Never use
plastic or other combustible
easy-to-puncture
ductwork.
* This appliance
must be properly
grounded
and installed
as described in these instructions.
" Do not install or store appliance
in an area where it
will be exposed to water and/or weather.
, The National Fuel Gas Code restricts installations
of
gas appliances
in garages. They must be 18 in. off the
ground and protected
by a barrier from vehicles.
, Install the dryer where the temperature
is above ,50°F
for satisfhctory operation
of the dryer control system.
MATERIALS YOU WILL NEED
%
4"DIA. M ETAL ELBOW
PIPE C OMPOUND
FLEXIBLE
GAS LINE CONNECTOR
4"DIA, METAL DUCT
DUCT
(RECOMMENDED) CLAMPS {2)
4"DIA. FLEXIBLE
METAL DUCT
(IF NEEDED)
GLOVES
SOAP S OLUTION
FOR LEAK DETECTION
EXHAUST
HOOD
SAFETY GLASSES DUCT T APE
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
VerifY/Your Gas Installation
(see
section
2).
Prepare the Area and Exhaust for Installation
of
New Dryer (see section 1).
Check and Insure the Existing External Exhaust is
Clean (see section 1) and Meets Attached Installation
Specifications.(see
section 6)
Remove the Foam Shipping Pads (see section 1).
Move the Dryer to the Desired Location.
Level _)ur Dryer (see section 8).
Connect the Gas Supply (see section 3) and check
fbr leaks (see section 4).
Step 8
Connect the External Exhaust (see section 7).
Step 9
Connect the Power Supply (see section 5).
Step 10 Check the Operation
of the Power Supply, Gas
Connections, and Venting.
Step 11 Place the Owners ManuN and the Installation
Instructions
in a Location Where They Will Be
Noticed By the Owner.
For Alcove or Closet Installation
see section !1.
For Bathroom
or Bedroom
Installation
see section 10
For Mobile or Manufactured
Home see section 11.

Advertisement

loading

Summary of Contents for GE DPSE592GA1AA

  • Page 1 BEFORE YOU BEGIN FOR YOUR SAFETY: Read these instructions compLeteLy c&re_[]yo I M P O RTANT - Save these , Use only rigid metal or flexible metal 4-in. diameter ductwork for exhausting to the outdoors. Never use instructions for local inspector's use.
  • Page 2 lnsta mation Instructions Minimum CUearance Other Than AUcove or CUoset Installation surfaces and for air opening are: 0 in. clearance both sides and 1 hr. rear. Consideration Minimum clearance to combustible must be given to provide adequate clearance ]br proper operation and service. [] PREPARING FOR INSTALLATION TILT THE DRYER SIDEWAYS...
  • Page 3 lnsta!lation Instructions [] RECONNECTING APPLY PIPE COMPOUND TOALLMALE THREADS, 1/8" NPTPIPE PLUG FOR NEW METAL FLEXIBLE G AS INLET PRESSURE LINE CONNECTOR SHUT-OFF ADAPTER VALVE 3/8"NPT ELBOW PIPE SIZE ITEMS NOTSUPPLIED ATLEAST 1 /2" TIGHTEN A LLCONNECTIONS USING TWO ADJUSTABLE WRENCHES, DONOT OVERTORQUE GASCONNECTIONS!
  • Page 4 h structions lnstaNmat[on [] ELECTRICAL CONNECTION [] EXHAUST INFORMATION IHLWARNING - USE ONLY METAL 4-IN. DUCT. WARNING- TO REDUCE THE RISK OF DO NOT USE DUCT LONGER THAN SPECIFIED FIRE, ELECTRICAL SHOCK, AND PERSONAL IN THE EXHAUST LENGTH TABLE. INJURY: Exhm_st longer thml specified will: °...
  • Page 5 lnstamlation Instructions [] EXHAUST CONNECTION G - TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY: " This dryer nmst be exhausted to tile outdoors. FOR STRAIGHT " Use oniy metal duct. LINE INSTALLATION, " Do not terminate exhaust in a chimney, any gas vent, CONNECT ELBOW H IGHLY under an enclosed floor (craw] space), or into an attic.
  • Page 6: Installation

    Installation Instructions USING FLEXNBLE METAL DUCTS [] ALCOVE OR CLOSET NSTALLATION If rigid all-nletal duct cmmot be used, then flexible all-metal " If your dryer is approved for installation in an alcove or venting cml be used, but it will reduce the maxinmm closet, it will be stated on a label on the dryer back.
  • Page 7 Installation Instructions ADDING DUCT [] DRYER EXHAUST TO LEFT OR BOTTOM OF CABINET FIXING HOLE PORTION "A" _- PROTECT YOUR HANDS AND ARMS FROM SHARP EDGES WHEN WORKING INSIDE CABINEZ LEFT SIDE REMOVE EXHAUST SCREW Reconnect the cut portion (A) of the duct to the blower ANDSAVE, housing.
  • Page 8 instructions Installation CHANGING DIRECTION ADDING ELBOW FOR EXHAUST DOOR OPENING THROUGH BOTTOM OF CABINET " Insert the elbow through the rear opening and connect it to the dryer internal duct. , Apply duct tape oil the joint between the dryer internal duct and elbow, as shown oil page 2 REMOVE 4 HOLE PLUGS A ND PLACE T HEM INTHE HOLES...

This manual is also suitable for:

Dpse592ga1wwDpse592ga0aaDbxr463pf0ccDpse592ga0wwDbxr463pf0wwDqsr483gg0ww ... Show all