Kenmore 630.1395 Installation Manual
Hide thumbs
Also See for 630.1395:
- Use and care manual (22 pages) ,
- Use & care manual (64 pages) ,
- Use & care manual (64 pages)
Advertisement
Quick Links
Download this manual
See also:
Use and Care Manual
Installation Guide
Instrucciones de Instalaci6n
instructions d'lnstallation
English / EspaioJ / Frangais
Models/Modelos/Mod_les:
630.1395 _
I<enmore Elite
P/N
9000561175
Rev. A
Sears
Brands Management
Corporation
Hofl:man
Estates_
IL 60179
U.S.A.
www.kenmore.com
www,sears,com
Sears
Canada
Inc,
Toronto,
OntarJo_
Canada
M5B
2B8
www.sears.ca
Advertisement
Related Manuals for Kenmore 630.1395
Summary of Contents for Kenmore 630.1395
- Page 1 Installation Guide Instrucciones de Instalaci6n instructions d'lnstallation English / EspaioJ / Frangais Models/Modelos/Mod_les: 630.1395 _ I<enmore Elite 9000561175 Rev. A Sears Brands Management Corporation Hofl:man Estates_ IL 60179 U.S.A. www.kenmore.com www,sears,com Sears Canada Inc, Toronto, OntarJo_ Canada www.sears.ca...
-
Page 2: Warnings And Cautions
Dishwasher Safety ............Water supply requirements ............Installation Requirements ..........Electrical requirements ..............Materials needed ..............Installation Instructions ..........Tools needed ................. Materials supplied ............... Pre-install checklist ............... Drain requirements ..............To avoid possible injury or property damage, OBSERVE ALL Make sure electrical work is properly installed. - Page 3 Read theseinstallatlon instructions c ompletely • This dishwasher is designed to be enclosed on the top and a nd follow both sides by cabinetry. them carefully. They will save you time and effort and help NEW INSTALLATION - If the dishwasher isa new installation, to ensure safety and optimum dishwasher...
- Page 4 Hammer Hole Saw Adjustable Wrench Safety Glasses Pliers Needle Nose Pliers Work Gloves Screwdrivers Level Drill Wire Strippers Measure Tape Mounting Bracket Screws Screw Clamp Spring Clamp ,'_,_ili_:':_i_ii_ _'_'_''i_J!_i,i_uii_iiiiiiiii Junction Box Screw Toe Panel Screws Drain Hose...
- Page 5 IMPORTANT! Before you begin, you must read the safety instructions! Avoid Scalding or Electrical Shock Hazard! PRE-INSTALL CHECKLIST Make sure the water supply and electrical supply are shut [] Unpack unit. Retain packing material until successful off before installation or service. installation is complete.
- Page 6 Note: Plumbing installations will vary - refer to local codes. Drain hose included is 92" (234 cm) and can be extended a maximum of 150" (381 cm). Ensure a portion of the drain hose is raised at least 20" (51 cm) above the floor.
- Page 7 STEP | Enclosure Preparation NOTE: This dishwasher is designed to be encMosed on the tap and both sides by standard residential kitchen cabinetry. Select a location as close to the sink as possible for easy access to water supply and drain lines. For proper dishwasher operation...
- Page 8 Electrlcal Supply Ensure that the dishwasher electrical installation is in compliance with all national and local electrical codes and ordinances. The dishwasher is designed for an electrical supply of 120V, 60 Hz, AC, connected to a dishwasher- dedicated, properly grounded electrical circuit with a fuse or breaker...
- Page 9 STEP 4 Removing the junction box cover While unit is still in position as shown here, remove the iunction box cover and set it aside. You will need it later. STEP 5 Removing the strain relief plate Once you remove the iunction box, remove the strain relief plate located directly...
- Page 10 STEP6 Attaching the hot water llne NOTE: The 90 ° elbow fitting is nat suppUied with the dishwasher and must be purchased separately (see _Materials Needed" section). STEP 1 To prevent leaks, wrap the dishwasher elbow with plumbing tape firmly in a clockwise direction twice.
- Page 11 STEP 7 Attaching the mounting brackets Flip unit back upright, ensuring water line remains in appropriate channel and is not pinched. If your dishwasher has the pre-attached mounting brackets as shown and you have a wooden undercounter, ensure that brackets are positioned as far apart as possible...
- Page 12 STEP 8 Connecting drain hose to the dishwasher To attach the drain hose, orient it towards the direction the sink. IMPORTANT: Route hose towards sink PRIOR to connection. DO NOT rotate the hose after attaching it to the dishwasher. This would cause it to crimp. Attach the drain hose elbow to the back of the unit with the included spring clamp.
- Page 13 STEP10 Attaching the strain relief Attach the strain relief (not included) ta the strain relief plate. The two screws on the back of the strain relief shauMd be positioned as shown to prevent interferences during assembly. Tighten the strain relief lock nut to prevent strain relief from turning.
- Page 14 Place the assembMed strain relief plate back into the iuncfion box and re-attach the screw. Make sure the tab on the right side of the strain relief plate is outside the iuncfion box as you slide it into place. Note: Do not loosen or remove terminal screws! Damage may occur.
- Page 15 Make sure that the exposed (non-insulated) portion of each stripped wire shows above and below the terminal screw. SecureJy tighten the terminal screws, but do not over-tlghten or damage may occur. STEP 12 Restoring the junction box cover Replace junction box cover. Make sure the cover is seated behind the front lip of the strain reJief plate.
- Page 16 STEP 13 NOTE: if the dishwasher is not level, it may not operate Adjusting the leg levelers properly and could cause leaks. Check that the leveling legs are firmly against the floor. Place a level against the front panel. Check that the dishwasher is plumb.
- Page 17 STEP 15 Drain Hose Connection Note: Plumbing installations will vary - refer to local codes. Drain hose included is 92" (234 cm) and can be extended a maximum of 150" (381 cm). Ensure a portion of the drain hose is raised at least 20" (51 cm) above the floor.
- Page 18 STEP 16 Attaching water llne and checking for leaks Attach water line to incoming hot water shut off valve. • Turn an water and check far leaks. • Turn power back on at fuse box. • Start washer, listen far water and pump far water distribution.
- Page 19 STEP18 Check operation • Turn the fuse back on. • Read the Use and Care Manual that came with your dishwasher. • Start the dishwasher and allow it to complete shortest wash cycle. • Check that the dishwasher is functioning properly water is coming into the unit.