Hsu-12Hra103/R2; Parts And Functions; Indoor Unit; Remote Controller - Haier HSM09HRAC03/R2(DB) Operation Manual

Haier split type room air conditioner operation manual
Hide thumbs Also See for HSM09HRAC03/R2(DB):
Table of Contents

Advertisement

Parts and Functions

Indoor Unit

Inlet
Inlet grille
Outlet
Anion generator
(inside)
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Actual indoor unit may vary from the one shown
in the manual, according to the product purchased.

Display board

1
2
3
Signal receiver hole
1
COOL
display
2
HEAT
display
3
TEMP display
4

Outdoor Unit

OUTLET
4
INLET

Clock set

Press CLOCK button, "AM" or "PM" flashes.
Press
or
to set correct time. Each press
or decrease 1min. If the button is kept pressed,time will
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
2
Air Purifying Filter
(inside)
Vertical blade
(adjust left and
right air fl
Display board
4
5
6
HEALTH display
5
(If the unit which you purchased
has healthy function,follow it.
If not,please
ignore.)
Dry
display
6
TIMER OFF display
7
TIMER ON display
SLEEP display
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
will increase

Remote controller

16
15
14
13
12
11
Emergency
Switch
ow)
2
1.CODE
Used to select CODE A or B
7
which
will be displayed on
LCD.
Please select A without
special
explanation.
2.LIGHT button
Control the lightening and
extinguishing of
LED display board.
3. TIMER button
4. CLOCK button
5. SLEEP button
6. MODE button
7. HOUR button
8. HEALTH button
The following functions and related displays are not
LIGHT button is not available for HSU-09HRA103/R2 and

HSU-12HRA103/R2.

Loading of the battery

4
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
type fluorescent lamp or
room, the recei
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batte
ries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
remove the batteries and
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key.
9. ON/OFF button
10. TIMER ON display
17
11. FAN SPEED display
18
LOW
19
12. LOCK display
20
13. SWING display
21
14. SLEEP display
22
15. HEALTH display
16. Operation mode display
23
Operation mode
24
Remote controller
25
17.Signal sending display
26
18. POWER/SOFT display
27
19.
TEMP display
28
20.
TIMER OFF display
29
CLOCK display
21.
30
22.
TEMP button
23.
FAN button
24.
SWING button
HEALTH AIRFLOW button
25. .
26.
FRESH button
27. SET button
28. POWER/SOFT button
29. LOCK
If pressed, the other buttons
be disabled.Press it once
will
the indoor
again,lock will be cancelled.
30. RESET
When the remote controller
appears abnormal,use a
sharp pointed article to press
this button to reset the remote
controller normal.
1
Remove the battery cover;
2
Load the batteries as illustrated.
2
2 R-03 batteries, resetting key
(cylinder);
1
3
Be sure that the loading
3
is in line with the " + "/"-";
wireless telephone is installed in the
ver is apt to be disturbed in receiving the signals,
reload several minutes later.
MED
HI
AUTO
AUTO
COOL
DRY
FAN
HEAT
button
button
available:
1
26

Advertisement

Table of Contents
loading

Table of Contents