Auxiliary Input; Troubleshooting Tips; Additional Information - RCA RCD175 User Manual

Auxiliary input

1. Connect the auxiliary device to the AUX IN jack
with an audio cable (not provided).
2. Press SOURCE until the indicator "
the display.
3. Start playback from the auxiliary device.
4. Adjust the auxiliary device to mid-range volume
and adjust the master volume by pressing
VOLUME
• Do not turn the volume of the auxiliary device too
high as this may affect the sound quality.
• For other playback operations, control them on your
auxiliary device.

Troubleshooting Tips

System doesn't turn on
• Unplug the unit for a moment, and then plug it back
in.
• Check the outlet by plugging in another devices.
No sound
• Adjust volume setting.
• Make sure you've selected the correct function.
Poor radio reception
• Rotate the unit for better reception.
• Try turning off electrical appliances near the unit,
such as hair dryers, vacuum cleaners or fl uorescent
lights.
CD doesn't play
• Make sure you've put a CD in the tray.
• Make sure the CD's label is facing up.
• Try another CD.
• Make sure that Pause mode is not activated.
• Make sure CD function is selected.
CD sound skips
• Clean the CD.
• Check CD for warping, scratches or other damage.
• Check for vibration or shock that may affect the unit;
move the set if necessary.
ESD Remark:
In case of misfunction due to electrostatic discharge
just reset the product (disconnect and reconnect of
the power source may be required) to resume normal
operation.

Additional Information

Cleaning the exterior
• Disconnect the system from AC power before clean-
ing the exterior of the unit with a soft dust cloth.
• Clean the exterior with a soft clean cloth or slightly
moistened chamois leather. DO NOT use solvents
as it may cause damage to the unit.
811-317591W012 EN & FR & ES IB OK Kelly.indd 6 811-317591W012 EN & FR & ES IB OK Kelly.indd 6
" lights on
.
Handling CDs
• Do not touch the signal surfaces. Hold CDs by the
edges, or by one edge and the hole.
• Do not affix labels or adhesive tapes to the label
surfaces. Do not scratch or damage the label.
• CDs rotate at high speeds inside the player. Do
not use damaged (cracked or warped) CDs.
• Make sure CDs are stored in their original case
after use. Keep them away from damp, humid or
abnormally heated places.
CD Lens Care
• When your CD lens gets dirty it can also cause
the system to output poor sound quality. To clean
the lens you will need to purchase a CD lens
cleaner which can maintain the output sound qual-
ity of your system. For instructions on cleaning the
CD lens, refer to the ones accompanying the lens
cleaner.
Cleaning CDs
• Dirty CDs can cause poor sound quality. Always keep
CDs clean by wiping them gently with a soft cloth
from the inner edge toward the outer perimeter.
• If a CD becomes dirty, wet a soft cloth in water,
wring it out well, wipe the dirt away gently, and
then remove any water drops with a dry cloth.
• Do not use record cleaning sprays or antistatic
agents on CDs. Also, never clean CDs with ben-
zene, thinner, or other volatile solvents which may
cause damage to disc surface.
Cassettes
• To protect your recordings from accidental erasure
on one or both sides of your cassette, snap out
the tab at the top of the cassette. If you decide
later to record on the tape, seal the hole with a
piece of adhesive tape. (Refer to diagram)
• Quit Slacking - A little bit of slack in your tapes can
cause scratches on the tape, or worse yet, the tape
could break. If you notice some slack in the tape,
use a pencil to tighten it up before you insert it.
EN - 6
9/16/2010 4:58:18 PM 9/16/2010 4:58:18 PM