INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Skyline Champion®4 2-piece Toilets
2067.014 Right Height™ Elongated: 3225.016 Bowl and 4077.014 Tank
2112.014 Round Front: 3110.016 Bowl and 4077.014 Tank
2219.014 Elongated: 3121.016 Bowl and 4077.014 Tank
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years.
To ensure this product is installed properly, please read these instructions carefully before you begin.
(Certain installations may require professional help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
NOTE: BACK-TO-BACK INSTALLATION
Depending upon your plumbing and venting conditions, the flow from
the Champion in a back-to-back installation may create a vacuum on
the system and draw water from the opposing bowl.
Standards Plumbing Code prohibits the use of a cross fitting for
drainage as throw over is possible.
directional "Y" style fitting with proper venting to direct the water
downward and away from the other toilet.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
Closet Bolts
Tape Measure
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN DIMENSIONS: Right Height™ Elongated Two Piece Toilet
FINISHED WALL
C
19mm ± 6mm
(1 ± 1/4)
235mm
(9-1/4)
C/L OF SEAT POST HOLES
140mm (5-1/2 CENTERS)
16mm
(5/8)
264mm
362mm
(10-3/8)
(14-1/4)
C/L OF OUTLET
305mm
(12)
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 7
The National
The code does approve a
Normal Height Round Front Two Piece Toilet
Normal Height Elongated Two Piece Toilet
A
SUPPLY
AS
REQ'D
B
*
254mm
(10)
152mm
(6)
FINISHED
FLOOR
Recommended fitting type for back-to-back installations.
Adjustable Wrench
Flexible Supply Tube
Carpenters Level
3
498mm
(19-5/8)
CLOSET BOLTS
356mm
(14)
D
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90 ° , and slide
into place 6" (152 mm) apart and parallel to wall.
MODEL
2067.014 Elongated
Right Height™
2-pc Toilet
2112.014 Round Front
254mm
(10)
Normal Height
2-pc Toilet
2219.014 Elongated
Normal Height
2-pc Toilet
Sealant
1/2" Deep Well Nut Driver or
Deep Well Socket Wrench
CLOSET FLANGE
DIMENSIONS
A
B
18-1/2"
16-1/2"
30-3/8"
470mm
419mm
772mm
16-1/2"
15-1/4"
28-3/8"
419mm
387mm
721mm
18-1/2"
15-1/4"
30-3/8"
470mm
387mm
772mm
7 30 94 5 -100 Rev. C
C
D
34-3/8"
873mm
33-1/8"
841mm
33-1/8"
841mm