Download Print this page
American Standard LEXINGTON 2037.100 Installation Instructions

American Standard LEXINGTON 2037.100 Installation Instructions

American standard lexington 1.6 gpf one-piece toilet installation instructions
Hide thumbs Also See for LEXINGTON 2037.100:

Advertisement

Quick Links

INSTALLATION
INSTRUCTIONS
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product
is installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
ROUGHING-IN DIMENSIONS:
2
NOTE: Distance from wall to closet flange centerline (rough-in)
must be 12" (305mm) minimum.
FINISHED WALL
743mm
(29-1/4)
305mm
(12)
C/L OF OUTLET
4
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 4
LEXINGTON 1.6 GPF ONE-PIECE TOILET
Model 2037.100 Elongated with Seat
Adjustable Wrench
Flexible Supply Tube
362mm
(14-1/4)
C/L OF SUPPLY
AS REQUIRED
WAX RING
Sealant
Closet Bolts
3
508mm
(20)
606mm
(23-7/8)
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90 , and slide
FINISHED
into place 6" (152 mm) apart and parallel to wall.
FLOOR
5
NUT
MTG. CLIP
BOLT
POSITION TOILET ON FLANGE
a.
Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b.
Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP" must face up!
Tape Measure
Carpenters Level
CLOSET FLANGE
CLOSET BOLTS
WASHER
305mm
(12)
FLANGE
Saniwares
7 3 0 4 0 3 - 1 0 0 R e v. C

Advertisement

loading

Summary of Contents for American Standard LEXINGTON 2037.100

  • Page 1 INSTALLATION INSTRUCTIONS Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
  • Page 2 MTG. CLIP WASHER INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions. Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings. METAL/COPPER METAL FLANGED FLARED TUBING...
  • Page 3 Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage. American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite).
  • Page 4 For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address: In the United States: American Standard Inc., P.O. Box 6820 Piscataway, New Jersey 08855...