Trane XR401 Comfort Control Owner's Manual
Comfort control
Hide thumbs
Also See for XR401 Comfort Control:
- Owner's manual (13 pages) ,
- Installer's manual (8 pages)
Related Manuals for Trane XR401 Comfort Control
Summary of Contents for Trane XR401 Comfort Control
- Page 1 (distributor) dealer local your 22-5206-05 Pub. contact information more 75707 Texas Tyler, Highway Troup 6200 Trane XR401 Comfort Control TCONT401AN21MA Comfort Control Owner’s Manual Mode Filter/OD...
- Page 2 Table Of Page Introduction Contents 4-11 Keypad functions 12-16 Features Factory settings Up Arrow - Increase 18-19 Comfort Control Setup temperature Page 5. 20-21 Troubleshooting 22-23 Warranty Comfort Information Drawer Page 16. Down Arrow - Decrease Mode Filter/OD temperature Page 5. Mode: Cool, Heat, Energy Savings Auto, Off, EMHeat...
- Page 3 XR401 Comfort Control. Your comfort settings are automatically stored in the XR401 Comfort Control’s memory eliminating the need for battery backup in the event of power loss. Simply follow the steps in this instruction manual and begin enjoying the benefits of your new Trane XR401 Comfort Control.
-
Page 4: Troubleshooting
Keypad MODE Functions - Pressing this key changes the system mode to Heat, Emergency Heat, Cool, Mode Automatic or Off. NOTE: Emergency Heat available only on Heat Pump applications. A border will appear around the mode on the display to show the system mode you’ve selected. Mode Page - 4 Pub. - Page 5 Trouble Table 2 Troubleshooting -shooting Symptom Possible Cause Action 1. Blown fuse or tripped circuit breaker. 1. Replace fuse or reset breaker. 2. Furnace power switch OFF. 2. Turn switch to ON. Display will not come on. 3. Furnace blower compartment door or panel 3.
- Page 6 Keypad Functions - Pressing this key selects whether the indoor fan motor runs in automatic or (cont-) continuous mode. The FAN ON indicates that you have selected to operate the fan in continuous mode. Continuous fan mode during cooling operation may not be appropriate in humid climates.
- Page 7 User Entering User Setup: Setup Press and hold the MODE and FAN keypad buttons at the same time. Options Keypad Navigation: - Use the MODE or FAN buttons to navigate forward and backward through the Setup steps. - Press MODE to advance forward to the next step. - Press FAN to return to the previous step.
- Page 8 Keypad FILTER/OD Functions - Press this key twice to display how many days remain before time to replace or Filter/OD (cont-) clean the filter. The “FILTER/OD” indicator will flash on the display when the filter timers days remaining reaches zero. Filter/OD - Press the “FILTER/OD”...
- Page 9 Features Calibrate Outdoor Temperature This option allows calibration (or deliberate miscalibration) of the outdoor temperature (cont-) sensor. The selected number is number of degrees, plus or minus, which will be added to actual temperature. The number can range between + 5 and - 5 degrees in 1/2 degree incre- ments.
- Page 10 Keypad Energy Savings Functions (cont-) - Use this key to lower your systems energy consumption and save money at the same time! Pressing the Energy Savings keypad button changes the indoor tempera- ture setting to a warmer temperature when the system is operating in the cooling mode and to a cooler indoor temperature setting when operating in the heating mode.
-
Page 11: Filter Reminder
Filter Reminder Features “FILTER/OD” will automatically flash to remind the homeowner that its time to change the (cont-) filter once the preset time has expired. Pressing the “FILTER/OD” keypad button automati- cally resets the internal clock timer. Once the timer has been reset, the number of days remaining till the next filter change can easily be determined by simply pressing the “FIL- TER/OD”... -
Page 12: Auto Changeover
Auto Changeover When the system mode is set to Auto, the control automatically switches between heating and Features cooling modes to maintain the desired comfort level. Appears when equipment is energized. Adjusting to new setting Setpoint Deadband The number of degrees separating Heating and Cooling setpoints. Neither the heating or cooling system operate when the indoor temperature is within the deadband.