Advertisement

V-027M User Guide
7/9/06
15:00
Page 14
UK
0QH,
recycle
product
Mon-Fri. 9.00am to 5.00pm. An answer phone is available out of these hours. If you have queries or concerns about using your VAX, call the HELPLINE. Calls are charged at the UK national rate.
Please make a note of the serial number and model number of your VAX before calling. There are over 400 approved VAX Service Agents in the UK. For your nearest Service Agent please call VAX Care.
www.vax.co.uk
WR9
Worcestershire
Droitwich,
advice.
recycling
for
retailer
or
Authority
Please
waste.
household
with
93/68/EEC
by
modified
as
Directive
93/68/EEC
by
modified
following:
the
with
compliance
the
that
declare
responsibility
own
COMPLIANCE
website:
-
info@vax.co.uk
email:
Lovett,
Hampton
Road,
Local
your
with
Check
of
disposed
be
not
should
products
compatibility
Electromagnetic
as
Directive
Voltage
Low
73/23/EEC
in
manufactured
is
pre-treatment
XL
our
on
hereby
Limited,
VAX
importer:
OF
STATEMENT
EEC
UK SERVICE & HELP - VAX CARE 0870 6061248
Kingswood
Ltd.,
Vax
exist.
facilities
where
electrical
Waste
EMC:
89/336/EEC
Rapide
V-027M
Manufacturer/EEC
Easy Guide

Advertisement

Table of Contents
loading

Summary of Contents for Vax Rapide XL

  • Page 1 Mon-Fri. 9.00am to 5.00pm. An answer phone is available out of these hours. If you have queries or concerns about using your VAX, call the HELPLINE. Calls are charged at the UK national rate. Please make a note of the serial number and model number of your VAX before calling. There are over 400 approved VAX Service Agents in the UK. For your nearest Service Agent please call VAX Care.
  • Page 2 V-027M User Guide 7/9/06 15:00 Page 1 Parts checklist Handle Front suction nozzle Solution/hose clip Solution trigger Dirty water tank Quick cord release Brush on/off Floor/tools selector aa Carrying handle Soap on/off Hose attachment cover bb Clean water tank cap Power on/off Dirty water tank handle cc Hose storage clips...
  • Page 3 V-027M User Guide 7/9/06 15:00 Page 2 Putting your cleaner together Feed the cord through the slots on Place a nut into the recess in the Remove the backing tape from the the back of the handle and push back of the upper handle. While screw cover and press into place.
  • Page 4 Note: The solution tank can be with clean water. Wash the carpet filled while it is attached to the as described in this guide, using cleaner but you should use care VAX AAA carpet cleaner. when refilling.
  • Page 5 V-027M User Guide 7/9/06 15:00 Page 4 Pre-treating your carpets with the pre-treatment wand and solution Remove solution tank cap. CAUTION: Do not overfill. You should leave Replace the solution tank cap. 1-2 cm of air space. Return the solution tank to the cleaner making sure the solution Fill the tank with pre-treatment solution.
  • Page 6 Tipping the cleaner and breaking the seal of the nozzle against the carpet will cause the float to rise cutting off suction. Once the float is activated, empty the dirty water tank. If the tank does not appear full turn off the power switch and wait for the float to settle. For best results use only VAX AAA Carpet Cleaner.
  • Page 7 1-2 cm of air space. Return the solution tank to the cleaner making sure the solution Fill the tank with VAX AAA Carpet Cleaner. tube lines up with the groove in the The cleaner can be stored with solution in the back of the solution tank.
  • Page 8: How To Operate

    V-027M User Guide 7/9/06 15:00 Page 7 How to operate your cleaner To spray cleaning solution, depress Plug the cord into an electrical Turn main power switch, brush the solution release trigger (3a) and socket. Step on the handle release switch and soap switch all to the move the cleaner backward and pedal to put the cleaner into a...
  • Page 9 V-027M User Guide 7/9/06 15:00 Page 8 Hose attachments Put the cleaner in its upright Remove the hose from its stored Insert the end of the hose into the position. Turn the brush switch and position on the back of the cleaner. tool opening and twist clockwise power switch to the off position.
  • Page 10 V-027M User Guide 7/9/06 15:00 Page 9 Hose attachments While depressing the blue solution spray Remove the hose from the fitting by Disconnect water supply connector trigger, pull the attachment in a downward twisting it counterclockwise to from the water supply port by motion.
  • Page 11: Emptying Dirty Water Tank

    V-027M User Guide 7/9/06 15:00 Page 10 Emptying the dirty water tank Depress the dirty water tank latch Remove the dirty water tank by Place the dirty water tank over a and simultaneously pull the dirty lifting the dirty water tank handle large sink and remove the dirty water tank nozzle tab up and away and pulling the tank out of the base.
  • Page 12 V-027M User Guide 7/9/06 15:00 Page 11 Emptying the dirty water tank Return dirty water tank to the base Lift the front of the cleaner base off of the cleaner by tipping the nozzle the carpeting with one hand. Line down into the basin and dropping it up the black tabs with the grooves into place.
  • Page 13 V-027M User Guide 7/9/06 15:00 Page 12 Belt or brush removal Belt or brush removal and replacement and replacement 1. Loop the belt around the rear shaft. Return the nozzle cover to the Remove the screw that holds the 2. Loop the top of the belt above the small original position.
  • Page 14: Troubleshooting

    • A hazard may occur if the appliance runs over the power supply cord. • Carpets should be dry vacuumed thoroughly before washing with the Rapide XL and Rapide XL Pro. For further information in the UK, call the VAX HELPLINE : 0870 606 1248...

This manual is also suitable for:

Rapide xl pre-treatment v-027m

Table of Contents