Table of Contents
Advertisement
Quick Links
Repair and Parts
™
GTX
- For Water-Based Materials Only-
Model: 257030
Sprayer with Graco Trigger Gun
120 psi (8.27 bar) Maximum Working Air Pressure
120 psi (8.27 bar) Maximum Working Fluid Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
Related Manuals
Operation:
313384
Gun:
310616
Pump:
309915
2000
EX
313385B
ti13066a
Advertisement
Table of Contents
Related Manuals for Graco GTX 313385B
Summary of Contents for Graco GTX 313385B
- Page 1 Repair and Parts ™ 2000 - For Water-Based Materials Only- Model: 257030 Sprayer with Graco Trigger Gun 120 psi (8.27 bar) Maximum Working Air Pressure 120 psi (8.27 bar) Maximum Working Fluid Pressure Important Safety Instructions Read all warnings and instructions in this manual.
- Page 2 Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.
- Page 3 PLASTIC PARTS CLEANING SOLVENT HAZARD Use only compatible water-based solvents to clean plastic structural or pressure-containing parts. Many solvents can degrade plastic parts and cause them to fail, which could cause serious injury or property damage. See Technical Data in this and all other equipment instruction manuals. Read fluid and solvent manufacturer’s warnings.
-
Page 4: Component Identification
Component Identification Component Identification ti13066a 313385B... - Page 5 Component Identification List A Nozzle Storage B Hopper C Hopper Quick Connect D Diaphragm Pump E Material Outlet Option 1 F Material Outlet Option 2 G Gun Air Outlet Quick Connect H Material (Pump) Air Pressure Gauge and Control Knob Gun Air Pressure Gauge and Control Knob K Gun (see manual 308878)* L Air Compressor (not supplied by Graco)
- Page 6 Preparation Preparation Pressure Relief 1. Disconnect air inlet. 2. Open gun air valve (23). ti4000b 3. Trigger gun, and spray material back into hopper. Hopper Removal and Installation The hopper (G) can be removed from the cart for clean- ing and servicing equipment. NOTE: Before removing hopper, allow unit to cool down and/or remove compressor power pack from cart.
-
Page 7: Pump Removal And Installation
Pump Removal and Installation Pump Removal 1. Relieve Pressure, page 6. 2. Remove hopper, page 6. 3. Disconnect air lines. 4. Disconnect exhaust tube. ti3889a 313385B 5. Remove four bolts holding pump to cart. 6. Lift pump straight up off cart. ti3888a Pump Installation 1. -
Page 8: Troubleshooting
Troubleshooting Troubleshooting Before performing any Troubleshooting procedures, follow Pressure Relief procedure on page 6. PROBLEM No material output from pump Pump stops pumping Pulsing or surging material Speed of application too slow CAUSE Not enough air pressure to pump Material too thick Damaged checkballs or seats Plugged gun or nozzle Plugged hose, or hose too small... - Page 9 PROBLEM Pattern too fine or too much overspray Pattern too coarse 313385B CAUSE Material too thin Air pressure at gun too high Fluid delivery too low Material too thick Air pressure at gun too low Fluid delivery too high Troubleshooting SOLUTION Thicken material.
-
Page 10: Parts Drawing
Parts Drawing Parts Drawing ti3953c 313385B... - Page 11 Parts Drawing 313385B ti3954c Parts Drawing...
- Page 12 Parts Drawing Parts Drawing ti3956a ti3955a 313385B...
-
Page 13: Parts List
Parts List Ref. Part Description 15C878 FRAME, texture, blue 801504 FOOT, rubber 15C843 HOPPER, texture, gas 116478 WHEEL, pneumatic 101242 RING, retaining, ext. 111841 WASHER, plain 5/8 246887 PUMP, diaphragm, 1040, texture 15C759 COUPLING, pump 15D985 FITTING, adapter, swivel 118457 GAUGE, panel, mount 169970 FITTING, line air 15B565 VALVE, ball 104641 FITTING, bulkhead... -
Page 14: Pump Parts Drawing
Pump Parts Drawing Pump Parts Drawing 10† 17† 18† *402 4† 6† 7† 9† 17† 10† 401* ▲110 108* ti12959a 301* 202* 201* 202* 301* 202* 202* 313385B... -
Page 15: Pump Parts List
Pump Parts List Ref. Part Description 188838 HOUSING, center, aluminum 188854 COVER, air valve, aluminum 116344 SCREW, mach, hex flange hd; M5 X 0.8; 12 mm (0.47 in.) 188618 GASKET, molded Santoprene 188855 CARRIAGE, aluminum 6† 108730 O-RING, nitrile 7† 188616 BLOCK, air valve, acetal 188615 PLATE, air valve, sst 9†... -
Page 16: Technical Data
Technical Data Technical Data Maximum air working pressure... . 120 psi (8.27 bar) Maximum working fluid pressure ..120 psi (8.27 bar) Compressor (not supplied) AIr Delivery . - Page 17 Notes Notes 313385B...
-
Page 18: Graco Warranty
Graco Warranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
Need help?
Do you have a question about the GTX 313385B and is the answer not in the manual?
Questions and answers