Download Print this page

Graco 243011 Manual

Graco inc. spray guns instructions manual
Hide thumbs Also See for 243011:

Advertisement

Quick Links

SG2, SG3 Spray Guns
Models: 243011, 243012, 246506, 243238, 243382, 289843, 257359
IMPORTANT SAFETY INSTRUCTIONS.
sprayer instruction manual for Pressure Relief, priming and
spray instructions. Keep these instructions.
Maximum Working Pressure: 3600 psi (248 bar, 24.8 MPa)
The following Warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point
symbol alerts you to a general warning and hazard symbols refer to procedure-specific risks. Refer back to these Warnings.
Additional, product-specific warnings may be found throughout the body of this manual where applicable.
WARNINGS
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured
components will pierce skin. This may look like just a
cut, but it is a serious injury that can result in amputation. Get
immediate surgical treatment.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the spray tip.
• Do not stop or deflect leaks with your hand, body, glove,
or rag.
• Do not spray without tip guard and trigger guard
installed.
• Engage trigger lock when not spraying.
Follow Pressure Relief Procedure in this manual, when
you stop spraying and before cleaning, checking, or ser-
vicing equipment
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes,
in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, ciga-
rettes, portable electric lamps, and plastic drop cloths
(potential static arc).
• Keep work area free of debris, including solvent, rags
and gasoline.
• Do not plug or unplug power cords, or turn power or light
switches on or off when flammable fumes are present.
• Ground all equipment in the work area. See Grounding
instructions.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering
into pail.
• If there is static sparking or you feel a shock, stop oper-
ation immediately. Do not use equipment until you iden-
tify and correct the problem.
• Keep a working fire extinguisher in the work area.
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2008, Graco Inc. is registered to I.S. EN ISO 9001
For the application of architectural paints and coatings -
-
.
Refer to your
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influ-
ence of drugs or alcohol.
• Do not exceed the maximum working pressure or tem-
perature rating of the lowest rated system component.
See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equip-
ment wetted parts. See Technical Data in all equipment
manuals. Read fluid and solvent manufacturer's warn-
ings. For complete information about your material,
request MSDS forms from distributor or retailer.
• Check equipment daily. Repair or replace worn or dam-
aged parts immediately with genuine manufacturer's
replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your
distributor for information.
• Route hoses and cables away from traffic areas, sharp
edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull
equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PRESSURIZED ALUMINUM PARTS HAZARD
Do not use 1,1,1-trichloroethane, methylene chlo-
ride, other halogenated hydrocarbon solvents or flu-
ids containing such solvents in pressurized aluminum
equipment. Such use can cause serious chemical reaction
and equipment rupture, and result in death, serious injury,
and property damage.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment
when operating, servicing, or in the operating area of
the equipment to help protect you from serious
injury. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and
solvent manufacturer
• Gloves
• Hearing protection
312830C
ti11562a

Advertisement

loading

Summary of Contents for Graco 243011

  • Page 1 SG2, SG3 Spray Guns Models: 243011, 243012, 246506, 243238, 243382, 289843, 257359 IMPORTANT SAFETY INSTRUCTIONS. sprayer instruction manual for Pressure Relief, priming and spray instructions. Keep these instructions. Maximum Working Pressure: 3600 psi (248 bar, 24.8 MPa) For the application of architectural paints and coatings - The following Warnings are for the setup, use, grounding, maintenance and repair of this equipment.
  • Page 2: Pressure Relief Procedure

    Pressure Relief Procedure WARNING Follow this Pressure Relief Procedure whenever instructed to relieve pressure, stop spraying, check or service equipment, or install or clean spray tip. Turn OFF power and turn sprayer pressure control to low- est pressure setting. Hold gun against side of flushing pail. Trigger gun into pail to relieve pressure.
  • Page 3 *Kit 288817 repairs both series A and B guns. 1a replaces these three components of series A. Series A Ref. Part Description 288817 KIT, repair, gun (includes 1a, 1b, 1c) SEAT, valve NEEDLE, gun 115483 NUT, lock 243639 TRIGGER, repair kit includes 32, 33 195495 GUARD, trigger...
  • Page 4: Technical Data

    Maintenance WARNING Before performing any maintenance on gun, read all warnings on front cover of this manual and relieve pressure. Cleaning/Replacing Filter (6) 1.Relieve pressure. Set trigger lock Disconnect fluid hose from gun at swivel (5). Disconnect trigger guard (4) from guard retainer (22). Unscrew handle (23) from gun (1).

This manual is also suitable for:

243012246506257359289843312830cSg2 ... Show all