Husky MP2500 User Manual

Hand-held computer
Hide thumbs Also See for MP2500:

Advertisement

Read ALL this leaflet before using your MP2500.
It contains essential information about getting
started, and setting up.
CAUTION -
battery types: it is very important to set
up the MP2500 correctly for the battery type you are
using. Refer to the section THE BATTERY inside this
leaflet. HUSKY battery types supplied with your
MP2500 can be as follows:
Either:
The MP2500 can be supplied with non-rechargeable
Alkaline batteries.
Alkaline batteries are not suited for use with
peripheral loads, or low temperature operation.
DO NOT charge non-rechargeable Alkaline batteries.
Or:
The MP2500 can be supplied with a rechargeable
battery option as follows:
NiCd (Nickel Cadmium) rechargeable battery
pack, colour coded black.
NiMH (Nickel Metal Hydride) high capacity
rechargeable battery pack, colour coded green
(special option only).
Rechargeable batteries should be charged before
use - refer to the section THE BATTERY inside this
leaflet.
In case of doubt, please contact your system provider.
H
USKY
User Leaflet
MP2500
MP2500

Advertisement

Table of Contents
loading

Summary of Contents for Husky MP2500

  • Page 1 CAUTION - battery types: it is very important to set up the MP2500 correctly for the battery type you are using. Refer to the section THE BATTERY inside this leaflet. HUSKY battery types supplied with your...
  • Page 2 - bright sunlight in a vehicle, for example prolonged immersion in water physical mistreatment The MP2500 leaves the factory without the battery fitted. You must fit the battery pack and charge it before use; refer to SETTING UP for instructions. PgUp...
  • Page 3: Serial Port Connector

    8 BACKLIGHT KEY: If the backlight option is fitted, press to illuminate the screen in low light. You may need to press at the same time (depending how your MP2500 is set up). 9 TYPING KEYS: type letters, or symbols and functions when used with S (SHIFT) 10 BACKSPACE KEY: press to erase typing.
  • Page 4 SETTING UP The MP2500 leaves the factory without the battery fitted. To get a new MP2500 started for the first time you must carry out the following steps: 1. Either: Fit three Alkaline batteries (see under Replacing the Battery later in this leaflet).
  • Page 5 G and H to adjust. You can use the same method to adjust 'seconds' if you wish. Press E to update the MP2500 clock and return to the Utility menu. Press J to select the Set Date option and press E.
  • Page 6: Turning On And Off

    Note: If non-rechargeable alkaline batteries are fitted, you must skip step 9. The MP2500 is now ready for use. Note: After an application has been loaded into MP2500, access to SETTING UP functions may be different. Refer to instructions provided with your application. CONTROLS Note: Your application's user instructions may supplement the following information.
  • Page 7: Moving The Cursor

    MP2500 in normal operation - use this procedure in emergency only. Report the problem to your system provider. If the MP2500 locks up or fails to operate, you MAY need to reset it as follows: Refer to the previous section SETTING UP. Carry out step 3, Reset the MP2500 and step 4, Starting MS-DOS.
  • Page 8: Replacing The Battery

    BATTERY LEVEL LOW will be displayed. (After a further period of use, your MP2500 will turn itself off and will not turn on again.) You should do one of the following: Return the MP2500 to your base or office...
  • Page 9: Charging The Battery

    Observe the instructions printed on the battery. Replace only with batteries approved by your MP2500 supplier. DO NOT FIT LITHIUM BATTERIES. ATTENTION: Dispose of or recycle used batteries according to the manufacturer's instructions, or local waste management regulations.
  • Page 10 CLEANING If the screen gets dirty or smeared, clean it with a clean cloth. If the MP2500 gets very dirty, it should be cleaned: Make sure that the battery cap is tight. If you have dropped the MP2500, check that the case and seals are intact.
  • Page 11: Ac Power Adaptor

    PROBLEMS If you have problems with the MP2500, TELL YOUR SYSTEM PROVIDER, but here are a few checks: If the unit will not turn on, check the battery pack orientation and try another charged battery pack. If you cannot read the display, try adjusting the screen contrast (see CONTROLS).
  • Page 12: Electromagnetic Compatibility

    Electromagnetic Compatibility CAUTION ! Approved accessories only may be used with this equipment. In general all cables must be high quality, shielded, correctly terminated and normally restricted to 2 metres length. H AC adaptors employ special provisions USKY to avoid radio interference and should not be altered or substituted. Unapproved modifications or operations conflicting with these instructions for use, may void approvals by the authorities to operate the equipment.

Table of Contents