Download  Print this page

Starting A Dishwashing Cycle; Changing / Interrupting / Cancelling A Wash Programme; Load Sensing; Switching Off The Dishwasher - Electrolux ESI 6220 User Instructions

Electrolux dishwasher
Hide thumbs

Advertisement

Starting a dishwashing cycle

1. Check that the dishes and cutlery are stacked in
the dishwasher in such a way that the spray arms
are free to rotate.
2. Turn on the water tap fully.
3. Close the door.
4. Press the ON/OFF button.
The LED in the ON/OFF button will illuminate.
5. Press the relevant button for the programme
required (see "Programme Table").
The programme display will illuminate. One or two
lights will flash in the programme progress display.
The selected programme will begin after approxi-
mately 3 seconds.
w
If
flashes in the programme progress
3
display after the programme has started,
please read the section "What to do if...".
Changing / interrupting / cancelling
a wash programme
Only change or interrupt a wash programme
3
that is in progress if it is absolutely neces-
sary. After the appliance door has been
closed again, the air that has entered will be
heated significantly and expand. As a result,
water may collect in the base of the appli-
ance and trigger the anti-flood system.
Changing a wash programme
If you would like to change the wash pro-
3
gramme in the first 3 seconds after having
selected a programme, press the button for
the new wash programme.
If you would like to change the wash programme after
this time, proceed as follows:
1. Press the button for the new wash programme
and hold it down.
First, the indicator for the wash programme that is
currently running will flash.
After several seconds only the indicator for the
new wash programme will be illuminated.
2. Release the programme button.
The newly selected wash programme will begin.
Interrupting the wash programme by
opening the dishwasher door
Hot steam may escape when the door is
1
opened. There is a risk of scalding. Open the
door carefully.
1. Open the door of the dishwasher.
The wash programme will stop.
2. Close the door.
The wash programme will continue.
Cancelling the wash programme
1. Press function buttons 2 and 3 and keep them
pressed.
The programme display for the current wash pro-
gramme will flash for several seconds and then go
out.
2. Release the function buttons.
The wash programme has been cancelled.
Turning off the dishwasher will only interrupt
3
a selected wash programme, not cancel it.
The wash programme will recommence after
turning the dishwasher back on again.

Load Sensing

If a wash programme is started even though there are
only a few dishes in the upper and/or lower basket, an
intelligent electronic system adjusts the amount of
water and the duration of the wash programme to the
number of dishes. By this means it is possible to
wash only a few dishes quickly and economically. At
half load (6 place settings), up to 2 litres of water and
0.2 kWh of electricity are saved.
Switching Off the Dish-
washer
Switch off the dishwasher when
the programme progress display.
1. Press the ON/OFF button. The ON/OFF button
indicator extinguishes.
Hot steam may escape from the appliance
1
when opening the door immediately after the
end of the programme. Therefore:
2. Open the door carefully.
Emptying the Dishwasher
3
Hot dishes are sensitive to knocks. The dishes
should therefore be allowed to cool down before
removing them from the appliance.
Leave the dishes in the dishwasher for approx.
15 minutes after the end of the programme so that
they dry better and can cool down.
First empty the lower basket, and then the upper
rack. By using this procedure you will avoid any
water that may be remaining in the upper basket,
dripping onto the dishes in the lower basket and
leaving water marks.
w
is illuminated on
23

Hide quick links:

Advertisement

Table of Contents
loading

  Related Manuals for Electrolux ESI 6220