1. Manuals
  2. Brands
  3. AEG Electrolux Manuals
  4. Hob
  5. 64500G-M
  6. Instruction booklet

AEG Electrolux 64500G-M Instruction Booklet

Gas hob
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
IE
GB
64500G-M
instruction booklet
gas hob

Advertisement

Table of Contents
loading

Related Manuals for AEG Electrolux 64500G-M

Summary of Contents for AEG Electrolux 64500G-M

  • Page 1 64500G-M instruction booklet gas hob...
  • Page 2 Thank you for choosing one of our high-quality products. To ensure optimal and regular performance of your appliance please read thisinstruction manual carefully. It will enable you to navigate all processes perfectlyand most efficiently. To refer to this manual any time you need to, we recommendyou to keep it in a safe place. And please pass it to any future owner of the appliance.

  • Page 3: Table Of Contents

    Contents For the User Important Safety Information ......................4 Description of the hob .......................... 6 Operation ..............................7 Maintenance and Cleaning ........................9 Something Not Working ? ........................11 For the Installer Technical data ............................12 Important Safety Requirements ....................... 14 Gas Connections ............................

  • Page 4: Important Safety Information

    English Important safety information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350. Installation • This appliance must be installed and • Children can also injure themselves by serviced by a competent person as stated pulling pans or pots off the hob.
  • Page 5 cause an accident by tipping or spillage. Environmental Information • Never leave the hob unattended when After installation, please dispose of the cooking with oil and fats. packaging with due regard to safety • Never use plastic or aluminium foil dishes and the environment.

  • Page 6: Description Of The Hob

    Description of the hob 1. Auxiliary Burner 2. Semi-rapid Burners 3. Rapid Burner 4. Control knobs INSTALLATION Any gas installation must be carried out by a registered competent person, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown.

  • Page 7: Operation

    Operation Hob burner control knobs The symbols on the knobs mean: When switching on the mains, after installation or a power cut, it is quite = no gas supply normal for the spark generator to be activated automatically. = maximum gas supply Do not keep the control knob pressed for more than 15 seconds.
  • Page 8 Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Burner minimum maximum diameter diameter Rapid 180 mm 260 mm Semi-rapid front 120 mm 180 mm rear 120 mm 220 mm Auxiliary 80 mm...

  • Page 9: Maintenance And Cleaning

    Mainteinance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine.

  • Page 10: The Pan Supports

    The pan supports To ensure a better cleaning, pan supports can be removed from the hob. Wash the pan supports using hot soapy water. If necessary, a paste cleaner or a soap impregnated steelwool pad can be used with caution. The pan supports are not dishwasher proof;...

  • Page 11: Something Not Working

    Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM SOLUTION There is no spark when lighting the Check that the unit is plugged in and gas.

  • Page 12: Technical Data

    Technical data Engineer technical data OVERALL DIMENSIONS Width: 594 mm Depth: 510 mm CUT OUT DIMENSIONS Width: 560 mm Depth: 480 mm SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V ~ 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse.

  • Page 13: Gas Burners

    Gas burners BURNER RAPID SEMI-RAPID AUXILIARY TYPE OF GAS POSITION MAX MIN NOMINAL THERMAL POWER 0.75 0.45 0.33 NATURAL GAS 20 mbar NOMINAL FLOW VALUE = RATE 0.286 0.057 0.190 0.038 0.095 0.028 37.78 MJ/m NOZZLE REFERENCE 11 9 Adjust. Adjust.

  • Page 14: Important Safety Requirements

    Important Safety Requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S.

  • Page 15: Gas Connections

    IMPORTANT Any gas installation must be carried out by a GAS SAFE REGISTER installer. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this instruction booklet...

  • Page 16: Location

    Location The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom, shower room or garage. Ensure that there is a minimum distance of 55 mm between the rear cut out edge and the wall.

  • Page 17: Fitting The Hob Into The Worktop

    Fitting the Hob into the Worktop Carry out the building in of the hob as follows: 1) place the seals supplied with the hob on the front edge of the cut out. Then, place them at 11 mm from the side edges and at 10 mm from the rear edge, as shown in the diagram, taking care that the seals meet without overlapping.

  • Page 18: Building In

    Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.

  • Page 19: Electrical Connections

    Electrical Connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230 V 50 Hz AC electrical supply.

  • Page 20: Permanent Connection

    Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations.

  • Page 21: Fault Finding

    Fault Finding Preliminary Electrical Systems Check Blue Brown Green Yellow START Isolate appliance Blue and carry out: A: Earth Continuity Green Brown check. Yellow Carry out: Carry out: D: Resistance to C: Polarity check. Earth check. Has inlet fuse blown? Electricity supply should now be satisfactory.
  • Page 22 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts clean and tight.
  • Page 23 Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse and Light burner manually replace if necessary Check by pass simmer Check polarity and earth adjusted continuity of supply point Check fitting of Check position of the Check earth continuity burners...

  • Page 24: Commissioning

    Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.

  • Page 25: Conversion From Natural Gas To Liquid Gas

    Conversion from Natural Gas to Liquid Gas IMPORTANT The replacement/conversion from natural gas to LPG should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted.
  • Page 28 www.aeg-electrolux.co.uk...

Table of Contents