Related Manuals for GMC LS1620
Summary of Contents for GMC LS1620
- Page 1 200W VARIABLE SPEED SCROLL SAW WITH REDEYE ® LS1620 INSTRUCTION MANUAL Black Magenta Code: LS1620 Cyan Yellow Date: 060906 Edition: 05 Op: BR...
-
Page 2: Table Of Contents
General safety instructions Additional safety rules for scroll saws Accessories Unpacking Assembly Know your product Mounting the saw to a workbench Blades Selecting the correct blade Removing blades Installing blades Setting the table for horizontal or bevel cutting Aligning the degree scale pointer... -
Page 3: Introduction
is a Warranty claim, spare part or user information, please phone our Help Line for an immediate response. Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand. Introduction Your new GMC power tool will more than satisfy your expectations. -
Page 4: Safety Rules For Laser Lights
Safety rules for laser lights The laser light/laser radiation used in the GMC REDEYE system is Class 2 with maximum 1mW and 650nm wavelengths. These lasers do not normally present an optical hazard, although staring at the beam may cause flash blindness. -
Page 5: Additional Safety Rules For Scroll Saws
Any alteration or modification not specified is misuse and may result in dangerous conditions. • For your own safety, do not operate your scroll saw until it is completely assembled and installed according to the instructions and until you have read and understood all of the instructions. -
Page 6: Accessories
Turn saw off and remove plug from power supply outlet before installing or removing blades. Wear safety goggles Wear ear protection Wear a breathing mask Accessories The GMC LS1620 Scroll Saw is supplied with the following accessories as standard: • 15 TPI saw blade • 18 TPI saw blade •... -
Page 7: Know Your Product
Know your product Before using the tool, familiarise yourself with all the operating features and safety requirements. Use the tool and accessories only for the applications intended. All other applications are expressly ruled out. 1. On/off switch / variable speed dial 2. -
Page 8: Mounting The Saw To A Workbench
1. Using the base of the scroll saw as a template mark the holes on the workbench through the holes in the casting. 2. Drill the holes through the workbench using an 8mm drill bit. -
Page 9: Installing Blades
Installing blades CAUTION. Always ensure that the saw is switched off and unplugged from the mains supply before removing or installing a blade. 1. Lift up the blade tension lever (12) to reduce the blade tension. 2. Remove the table insert (11) by raising it with a screwdriver. -
Page 10: Turning On And Off
Turning on and off 1. To turn on the scroll saw lift the on/off switch (1). 2. To turn off the scroll saw push the on/off switch (1) down. Sawdust blower Your scroll saw features a sawdust blower (6) to help keep the work area clean for more accurate scroll cuts. -
Page 11: Adjusting The Speed
2.4mm 0.3mm 5. The saw will not cut wood by itself, you allow the saw to cut wood by guiding the wood into the blade as it moves. 6. The drop foot (8) should always be lowered until it just... -
Page 12: Using The Redeye ® Laser Line Generator
7. Switch off the laser beam on completion of the cut. 8. Once finished push the on/off switch down to turn off the saw and unplug the tool from the power point to prevent unauthorised use. Maintenance WARNING. -
Page 13: General Inspection
General inspection Regularly check that all the fixing screws are tight. They may vibrate loose over time. Repairs Only an authorised service centre should replace the cordset or effect other repairs. If the cordset is damaged or worn, have it repaired or replaced by an authorised service centre. - Page 16 GMC customer assist If your product needs repairing, replacing, technical service or you simply need help or advice, please contact us on our Customer Assist Line 1300 880 001 (Australia) or 0800 445 721 (New Zealand). For prompt service we suggest you log your service request online at www.gmcservice.com.au.