Messages Shown On The Display - Brandt Instructions For Use Manual

EN 7 / SPECIAL MESSAGES SHOWN ON THE DISPLAY
•INCIDENTS INDICATED, WHICH YOU CAN
REPAIR YOURSELF
In this section, we explain how you can rectify these incidents very
easily yourself.
Your appliance automatically detects certain operating problems and
notifies you of these by special messages that appear on the screen, by
the incident warning symbol
"beep".
Messages Causes / Remedies
Tap safety system. When the water tap is still
closed:
— A few minutes after the washing cycle starts:
- The cycle stops,
- The message "Open the water tap / Press
- The problem warning symbol flashes and the
Incident d01
— If you have selected a delayed washing cycle,
Open the water tap
the time counts down until the cycle starts and
no signals are issued during this countdown
period.
— If you see and/or hear these signals:
- Open the water tap,
- Press the "Start/Pause" button to make the
- The cycle will restart.
— This incident may also be caused by the drain
hose being poorly connected (see the section
"DRAINING AWAY THE WASTE WATER").
The pump filter is clogged. The message
"Draining fault / Clean the filter and press Start"
appears on the screen, the problem warning
symbol flashes and the machine emits a
continuous "beep".
Draining fault
Clean the filter and pr
In this case, clean the pump filter (for how to do
this, see the Section "CLEANING THE PUMP
FILTER") and then press the "Start/Pause"
button to restart the cycle.
Also check the drain hose's position in the drain:
the connection must not be airtight (see the
section "DRAINING AWAY THE WASTE
WATER").
Door safety system. When your washing
machine's door is poorly closed:
— If you have selected an immediate start or after
a pause,
-The cycle does not start
- The message "Close the door / Press Start"
- The problem warning symbol flashes and the
Incident d07
Close the door
— If you have selected a delayed washing cycle
and this incident occurs during the waiting
period before the cycle starts, the time delay
counts down, the cycle starts and then,
approximately one minute after the cycle has
started, the above signals are emitted.
— If you see and/or hear these signals:
- Close your washing machine's door,
- Press the "Start/Pause" button to make the
- The cycle will restart.
Selector wrongly positioned. The message
"Selector wrongly positioned" appears on the
screen, the problem warning symbol flashes
Incident d09
and the machine emits a continuous "beep".
Selector wrongly pos
When programming, you have positioned the
selector knob
Turn the knob so that the indicator light for
the programme you have selected lights up. The
message goes out and you can finish
programming.
flashing and by issuing a continuous
Start" appears on the screen,
machine emits a continuous "beep".
signals disappear
appears on the screen,
machine emits a continuous "beep".
signals disappear
1
between two programmes.
•INCIDENTS INDICATED REQUIRING A
BREAKDOWN ENGINEER
Important:
Check that the message displayed is not for an incident you can
repair yourself.
Your machine also detects some operating faults that systematically
require the services of a breakdown engineer and informs you of this
through other messages of we provide some examples below.
In this case, the screen shows "Incident d.. / Call the After-Sales Service",
the symbol flashes and the machine emits a continuous "beep".
Messages
Incident d04
Call the After-Sale
When you encounter one of these messages, remember to note down
the message displayed (Incident d04, d05, etc.) so that you can inform
your breakdown engineer to assist him in his task.
NB:
Before calling your breakdown engineer, we recommend that you do
the following:
- Press the "On/Off" button and remove the electrical plug for at least
10 seconds
- Reconnect the plug and restart a washing cycle.
If the fault persists, call your breakdown engineer and remember to tell
him which indicator lights were lit.
Important:
Do not restart a washing cycle if the drum remains locked or if
you notice water around your machine of if you notice a burning smell.
• AFTER-SALES SERVICE :
Possible maintenance on your washing machine should be undertaken by :
—
either your dealer,
— or another qualified mechanic who is an authorized agent for the brand
appliances.
When making an appointment, state the complete reference of your equipment
(model, type and serial number). This information appears on the manufacturer's
nameplate attached to the rear of the equipment.
To keep your appliance in good working order, we recommend that
you use Clearit household products.
Professional expertise for the general
public
Clearit offers you professional products and adapted solutions for
the daily upkeep of your household and kitchen appliances.
You may find them in conventional retail outlets, along with a complete
line of by-products and consumables.
26
Incident d05
Call the After-Sale
etc...