Chamberlain Secure Home SH-9132AU Installation And Operating Instructions Manual

Motion sensing coach light

Advertisement

Quick Links

Models: SH-9132AU, SH-9133AU,
SH-9138AU, SH-9144AU, and
SH-9150AU
Installation and Operating Instructions
FEATURES
• Automatically comes on when motion is de-
tected.
• Automatically turns light off.
• Photocell keeps the light off during daylight
hours.
UNPACKING
Be sure to remove all contents from packaging
and verify all items are present before assembling
this light fixture. This package includes the fol-
lowing items:
• Coach Light
• Mounting Bracket (Mounting Bracket Screws
Are Not Included - Use 4mm dia. (8G) x 30 mm
Screws)
• Owner's Manual
• Some models will include an additional tail
assembly
Before installation, record the model num-
ber listed inside the fixture. Attach receipt
in case of possible warranty issues.
Model Number:
© 2011 The Chamberlain Group, Inc
®
TM
Motion Sensing
REQUIREMENTS
• The light control requires 230 volts AC.
• If you want to use Manual Mode, the control
must be wired through a switch.
• It is illegal for persons other than a licensed
electrician or person authorized by legislation
to work on fixed wiring or other electrical
installations.
Coach Light*
*Note: Illustrations are for reference only and may
be different from actual product
Coach Light
201101-01A

Advertisement

Table of Contents
loading

Summary of Contents for Chamberlain Secure Home SH-9132AU

  • Page 1 • Some models will include an additional tail assembly Coach Light* *Note: Illustrations are for reference only and may be different from actual product Before installation, record the model num- ber listed inside the fixture. Attach receipt in case of possible warranty issues. Model Number: © 2011 The Chamberlain Group, Inc 201101-01A...
  • Page 2 IMPORTANT SAFETY AND INSTALLATION INFORMATION Before installing coach light, read all instructions carefully and keep owner’s manual for future refer- ence. • WARNING: To prevent electric shock, please ensure that power is disconnected before installation. • This fixture must be connected to a 230V-240V ~ 50Hz power source. • The fixture must be properly grounded. • This fixture is designed for outdoor installation and should be mounted to a wall. • To achieve best results, this fixture should be mounted 1.8 meters (6 feet) above the ground. • Do not use dimmer switches or timers with this fixture. The sensor on this light fixture detects “motion” by the movement of heat across the coverage area. However, following are examples of objects that also produce heat and can cause the sensor to trigger: • Pools of Water • Air Conditioners • Dryer Vents • Animals • Heating Vents • Automobile Traffic If you suspect that a heat source of this type is triggering the sensor, reduce the sensitivity. The sensor on this fixture is more sensitive to the movement of heat moving across the coverage area and less sensitive to the movement of heat directly towards it. Motion Motion Sensor Least Sensitive Most Sensitive 201101-01...
  • Page 3: Installation

    INSTALLATION Decorative Nut This light fixture must be installed by a Mounting licensed electrician or other person autho- Bracket rized by legislation to work on fixed wiring or other electrical installations. Fixture WARNING: Turn power off at circuit Mounting Screw breaker or fuse.
  • Page 4: Final Assembly

    WIRING FINAL ASSEMBLY 1. Double check all wiring connections. WARNING: Turn power off at circuit 2. Slide the fixture assembly onto the mounting breaker or fuse. Place tape over circuit screws as shown on outer carton packaging. Make breaker switch and verify power is off at sure wires do not obstruct mounting screws (see the fixture. Figure 4). 3. Tighten decorative nuts removed in step 1 of In- stallation section securely against fixture base. WARNING: Risk of electric shock. 4. Caulk around fixture base with silicone weather Terminal block insulator must cover sealant. IMPORTANT: Ensure that the drain hole...
  • Page 5: Testing And Adjustments

    TESTING AND ADJUSTMENTS Fixture Top Decorative Screw 1. Turn on the circuit breaker and light switch. minute warm up period Note: Sensor has a 1 before it will detect motion. When first turned on wait 1 minutes. 2. Set: • ON-TIME switch to TEST • SENSITIVITY to Mid (M) position Figure 5 TEST 1 5 10 MIN LO - M - HI ON-TIME SENSITIVITY 3. Walk through the coverage area noting where you are when the lights turn on. In TEST mode, light will stay on for 5 seconds after motion has stopped and then turn off.
  • Page 6: Operation

    OPERATION Mode: On-Time Works: Day Night Test 5 Seconds 1, 5, or 10 Auto Minutes To Dawn* Manual * resets to Auto Mode at dawn. Rotating Sensor Head to Change Coverage Area Note: W hen first turned on wait about 1 minutes Figure 8 for the circuitry to calibrate. 5. Increase or decrease the sensitivity as needed. MANUAL MODE Too much sensitivity may cause false triggering due to heat sources in the coverage area (see Manual mode only works at Troubleshooting section). night because daylight returns 6. Set the amount of ON-TIME you want the the sensor to AUTO.
  • Page 7: Specifications

    2. Sensitivity is set too high. 2. Reduce sensitivity. Light stays on 1. The sensor may be picking up a heat source like an air 1. Re-aim sensor. Reduce sensitivity. continuously. vent, dryer vent, or brightly painted, heat-reflective surface. 2. Light control is in Manual mode. 2. Switch to Auto. 3. Sensitivity is set too high. 3. Reduce sensitivity. Light flashes on 1. Light control is in the TEST mode and warming up. 1. Flashing is normal under these conditions. and off. 2. Heat being reflected from other objects may be affecting 2. Re-aim sensor. Reduce sensitivity. the sensor. The Chamberlain Group reserves the right to discontinue products and to change specifications at any time without incurring any obligation to incorporate new features in products previously sold. 201101-01...
  • Page 8 CHAMBERLAIN LIMITED WARRANTY Lighting and Chime Products Chamberlain Australia Pty Limited / Chamberlain New Zealand Limited (Chamberlain) is committed to manufacturing and supplying high quality goods. As part of this commitment, we seek to provide reliable service and support for our goods and are pleased to provide you, the original purchaser, with this Chamberlain Limited Warranty. We also provide the following statement as required by the Australian Consumer Law: In Australia, in addition to your rights under this Chamberlain Limited War- ranty, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Chamberlain’s warranty Chamberlain warrants to the original purchaser of the lighting or chime product (including any LED lights which are provided by Chamberlain as part of the goods) (Unit) that the Unit is free from defects in materials and workmanship for a period of 12 months from the date of purchase. During the applicable Chamberlain Limited Warranty period, if you are concerned that the Unit may be defective, contact your retailer who will provide you with a replacement Unit or refer you to our service centre for a factory repair or replacement. If your retailer refers you to us, call our service centre on the toll free number below and a Chamberlain technician will diagnose the problem. Once the problem has been diagnosed, subject to your rights under the Australian Consumer Law with respect to major failures, Chamberlain will provide you with shipping instructions for a factory repair or replacement.

This manual is also suitable for:

Secure home sh-9138auSecure home sh-9133auSecure home sh-9144auSecure home sh-9150au

Table of Contents