Advertisement
Remove the grease grille and wash them either
by hand or in the dishwasher using neutral
detergent.
Any fat deposits should be removed from the
appliance periodically depending on amount
of use (at least every 2 months). Avoid using
abrasive or corrosive products. To clean
painted appliances on the outside, use a cloth
dipped in lukewarm water and washing up
liquid. To clean steel, copper or brass
appliances on the outside, it is always best to
use specific products, following the
instructions on the products themselves. To
clean the inside of the appliance, use a cloth
(or brush) dipped in denatured ethyl alcohol.
DESCRIPTION
-----------------------------------------------------------
The appliance can be used in both the filtering and
ducting version.
In the Filtering version (Fig. 1), the air and va-
pours conveyed by the appliance are depurated
by charcoal filter(s) and recirculated around the
room. ATTENTION: Using the hood as a filtering
one it is necessary to use the charcoal filter(s) that
purifies the air sent back into the room.
In the Ducting version (Fig. 2), cooking vapour
and odours are exhausted straight outside by a
disposal duct which passes through the wall/ceil-
ing. Use of charcoal filter is therefore unneces-
sary.
According to the model you have bought, the ap-
pliance can include 1 or 2 motors. In the 1 motor
version the flange for the air to be exhausted has
not got a central position, but it is slightly on the left.
INSTALLATION
-----------------------------------------------------------
Before assembling, in order to move the appliance
more easily, take off the grease grille (Fig. 3): pull
the front of the grille upwards; remove the back
from its seat.
IMPORTANT: So as not to damage your
product, during installation ONLY USE THE
SCREWS PROVIDED. Make sure these are
used as shown in the following instructions.
To compensate for any uneveness between
the appliance and the wall, a plastic SPACING
BAR must be fixed at the back of the appliance
by means of the three screws A is included
(Fig.4). The 3 screws A to be used are
contained in the accessory bag attached to
the plastic spacing bar. Cut the spacing bar
according to the distance to be adjusted.
Assembly under a wall cupboard
The following operations are essential for as-
sembly:
–
Install the wiring system
–
Prepare the air venting outlet if your appliance
is to be installed in the Ducting version.
Installation as indicated in Fig. 5:
Using the template make the 4 necessary
fixing holes in the bottom of the cupboard
and cut the air vent hole.
Move the hood close to the bottom of the
wall unit and then connect the two units by
means of the 4 self-tapping screws sup-
plied together with the appliance.
Installation with brackets as in Fig. 6 (optio-
nal):
Take the two brackets (S) out of the
accessory bag together with the 8 screws
provided. Fit the brackets to the wall unit
being careful to position these correctly; for
this operation use the 4 longer screws. At
this point, secure the appliance to the
brackets using the 4 shorter screws.
Ducting version: fit the flange of the hood with the
air vent hole made previously in the wall/ceiling by
means of an suitable tube. Connect the mains
cable to the electricity supply. Assemble the grease
grille with the hood, inserting it with the front edge
upwards.
Filtering version: fit a suitable hose to the flange of
the hood so that the air is recirculated back into the
room. Connect the mains cable to the electricity
supply. Fit the charcoal filter inside the grease grille
securing it by means of the 2 metal wires supplied
(F), as indicated in Fig. 3. Assemble the grease
grille with the hood, inserting it with the front edge
upwards.
OPERATION
-----------------------------------------------------------
Controls (Fig. 7):
A = ON/OFF 1st speed switch
B = II speed switch
C = III speed switch
The motor is automatically switched ON or
OFF by opening/closing the visor (unless
switch A is in position 0). Upon opening the
visor the previously selected speed is used.
D = Light switch. Position A (automatic), the light
is automatically switched ON or OFF by the
opening/closing of the visor. Position M
(manual), the light is on. Position 0, the light
is off.
If the hood is used in the filtering version
Advertisement
