Toshiba E-studio2555c Troubleshooting Manual page 13

Message
READY (CHECK SADDLE STITCH
STAPLER)
READY (CHECK SADDLE STITCH
STAPLER)
READY (CHECK STAPLER)
READY (CHECK STAPLER)
READY (HOLE PUNCH DUST BIN IS
FULL)
READY (FINISHER FULL)
READY (INNER TRAY FULL)
Cannot copy
Check DEPARTMENT COUNTER
Add paper
Call for service
Examine stapler in the Saddle Stitch
unit
Check staple cartridge in the Saddle
Stitch unit
Check staple cartridge
Examine Stapler
Saving energy - press START button.
CHANGE DRAWER TO CORRECT
PAPER SIZE
Time for periodic maintenance
POWER FAILURE
ERASING DATA
Problem Description
Staple jam has occurred in the stapler
of the saddle stitch unit.
No staples are left in the stapler of the
saddle stitch unit.
Staple jam has occurred in the stapler
of the finisher.
No staples are left in the stapler of the
finisher.
Hole punch dust bin is full of paper
punchings.
The receiving tray of the finisher is full
of paper.
The exit tray of the equipment is full of
paper.
The number of originals to be
scanned has exceeded the limit
specified with the department code
during scanning.
No paper is left in a drawer or on the
bypass tray.
The equipment requires adjusting by
a service technician.
Staple jam has occurred in the stapler
of the saddle stitch unit.
No staples are left in the stapler of the
saddle stitch unit.
No staples are left in the stapler of the
finisher.
Staple jam has occurred in the stapler
of the finisher.
The equipment has entered into the
energy saving mode since it has not
been used for a certain time.
No paper suitable for the original is
set.
The size of the original is not detected
correctly because the original is sent
from the Reversing Automatic
Document Feeder at a skew.
The equipment requires inspection
and maintenance by a service
technician.
A job was interrupted by a power
failure or some other reason.
The Data Overwrite Enabler is
clearing the data.
1 TROUBLESHOOTING FOR THE HARDWARE
Corrective Action
Remove the jammed staples.
 P.49 "Staple jam in the Saddle Stitch unit"
Refill the staples.
 P.62 "Refilling Saddle Stitch unit staples"
Remove the jammed staples.
 P.45 "Clearing a Staple Jam"
Refill the staples.
 P.59 "Refilling With Staples"
Remove the paper punchings.
 P.68 "Cleaning the Hole Punch Dust Bin"
Remove the paper from the receiving tray of the
finisher.
Remove the paper from the exit tray of the equipment.
Ask your administrator for details of setting the limit for
the number of copies.
Set paper in the drawer or on the bypass tray. The
touch panel indicates which drawer (or the bypass
tray) has no paper.
To set paper, refer to the Copying Guide.
Contact your service representative with the error
code displayed on the right side of the touch panel.
Never attempt to repair, disassemble or modify
the equipment by yourself.
You could cause a fire or get an electric shock.
Always contact your service representative for
maintenance or repair of the internal parts of the
equipment.
Remove the jammed staples.
 P.49 "Staple jam in the Saddle Stitch unit"
Refill the staples.
 P.62 "Refilling Saddle Stitch unit staples"
Refill the staples.
 P.59 "Refilling With Staples"
Remove the jammed staples.
 P.45 "Clearing a Staple Jam"
Press any of the [START], [COPY], [e-FILING],
[SCAN], [PRINT], [FAX] and [ENERGY SAVER]
buttons to clear the energy saving mode.
Place the suitable size paper for the original in the
drawer.
Replace the original while aligning the side guides of
the Reversing Automatic Document Feeder to its
width so that it will be placed straight.
Contact your service representative for maintenance.
The print or fax job may be incomplete. Press [JOB
STATUS] to check whether any jobs are unfinished.
To clear the messages, press the [FUNCTION
CLEAR] button twice.
This message is displayed if the Data Overwrite
Enabler is installed. You can operate the equipment
while the message is displayed.
Messages Displayed on the Touch Panel 11