Advertisement
CONNECTING
TO THE ICEMAKER
FORMODELS
GXRV10,
GXRM10,
PNRV12
L Locate
the 3/8"
robing that supplies
file product
water to ltle
RID fauco.
It will be bhm, gray or white, depending
on tile
model. DO not confuse the product water tubing with the drain
water tubing that also goes to the faucet (black or white on most
models), At a convenient
point
between
tile faucel and the
eleclronics
box (oil mine models),
cut tile robing
and install
tile second
Tee filling.
Connect
one end of the 33-foot lenffih
of blue robing a_sshown in Fig. 4.
2. Turoofficemakerwatersuppl_Disconnectdmwatersource
tubing
from dm reffigeralor.
3. Connect
lhe brass tubing
adapter
to tile flee end of the
3Nfoot length
of bhm tubing.
Shorten
tubing
to desired
lengfll.
Attach
the other
end of file adapter
to the icemaker
water
valve. Be sure lo install tile plastic washer into tile tubing
adapter
as shown in Fig. 5.
SANITIZING
THE SYSTEM
FOR MODELS
GXRV10,
GXRM10,
PNRV12
See your Reverse Osmosis System Owner's Manual for complete
8, Remove sumps. Inert fillers. Lubricate o-ring with food-grade
Sanitization Instructions.
L Remove
lhe sumps.
ReInove
the filters and place in a clean
plastic bag. flit has been six months
since y_u last replaced
fillers, go ahead and discard
dram and replace
wilh new fillers.
2 Thoroughly
wash sumps with dish soap. Thoroughly
wipe
inside of head wifll a paper
towel moistened
wifll dish soap.
Rinse well.
3. Remove
cap froIn RID cartridge
housing.
ReInove
the RID
cartridge
mid place in a cleml plastic tyag. Thoroughly
wipe
inside
the housing
and cap with a gaper towel or dish brash
moistened
wifll dish map. Rin_
well.
4, Replace
empty
poslfilter
suInp and RO housing
cap.
5, Fill prefilter
sunlp with water to wilhfil 1ppof o-ring. Add 2 oz.
(4 Tbsp.)
of ordinary
household
bleach.
Replace
prefilter
sump.
6. Make sure t_th
tanks are sitting al tile _me
elevation.
Olherwi_,
Ihe higher
tank may not be _nitized
properly.
Turn
oil water supply. Open
RO faucet
until water begins m flow,
then close. Allow system to fill fbr one minute.
Z Open
Ihe faucet and allow water to flow for 10 minutes.
Clo_
f_tucet fi)r one minute
more,
Ihen open
mid allow water lo flow
for anolher
10 minutes,
or until tile bleach
odor is gone.
"Ibm
offwater
supply again. Drain RO system.
9.
10.
11.
12.
silicone
g-tease, if necessa_.
DO not use petroleum jellg Tighten
sumps
securely.
Remove
cap from RO cartridge
housing,
lnslall RID carlridge,
o-ring end first. Lubricate
cover o-ring wilh fbod%rrade
silicone
grease,
if necessary.
DO not use petroleum ]ellg Tighten
cap
securely.
TurIl oil water supply. Allow m fill. It may lake 4-8 hours
m fill
boil, ranks. Check for leaks,
If y_u replace
die prefiher
and postfiher,
allow faucet
m run a
few lninules
|O reInove
harmless
carbon
panicles.
Once
storage
tanks are filll, turn Oil icemaker,
lfyou
have a
concern
that some oflhe
bleach water may have badkwashed
inlo the iceInaker
iIflet lines, discard
Ihe first two balches
of
ice. Or, dr'din your dispenser
tank until water IlO longer
runs
cold, and check for bleach
taste and odor.
Br,tss robing
adap_r
Hg. 3
This
tubing
adapter
can be nsed
On ill(k_t
icvmakcrs.
Obtain
iwed¢.d
tilting
for otheix.
Product
_atcr
tubv
4
Tee
titting ,,_1
Plastic
w&she r
(on
some
medals)
Storage
rank
To drain
point
supply _-alve
J
Secondal'y
storage
tank
(included
w5th R'_]glT)
Advertisement
