Adjusting The Cutting Angle; Maintenance; Cutting Aluminum Extrusion; Groove Cutting - Makita LS1016 Instruction Manual

Table (C)
Molding position
in Fig. 47 & 48
For inside corner
For outside corner
7.

Cutting aluminum extrusion

When securing aluminum extrusions, use spacer blocks
or pieces of scrap as shown in Fig. 52 to prevent defor-
mation of the aluminum. Use a cutting lubricant when
cutting the aluminum extrusion to prevent build-up of the
aluminum material on the blade.
WARNING:
• Never attempt to cut thick or round aluminum
extrusions. Thick or round aluminum extrusions can
be difficult to secure and may work loose during the
cutting operation which may result in loss of control and
serious personal injury.
8. Groove cutting (Fig. 53)
A dado type cut can be made by proceeding as follows:
Adjust the lower limit position of the blade using the
adjusting screw and the stopper arm to limit the cutting
depth of the blade. Refer to "Stopper arm" section
described previously.
After adjusting the lower limit position of the blade, cut
parallel grooves across the width of the workpiece using
a slide (push) cut as shown in the figure. Then remove
the workpiece material between the grooves with a
chisel.
WARNING:
• Do not attempt to perform this type of cut by using
a wider type blade or dado blade. Attempting to
make a groove cut with a wider blade or dado blade
could lead to unexpected cutting results and kickback
which may result in serious personal injury.
• Be sure to return the stopper arm to the original
position when performing other than groove cut-
ting. Attempting to make cuts with the stopper arm in
the incorrect position could lead to unexpected cutting
results and kickback which may result in serious per-
sonal injury.
Carrying tool
Make sure that the tool is unplugged. Secure the blade at
0° bevel angle and the turn base at the full right miter
angle position. Secure the slide poles so that the lower
slide pole is locked in the position of the carriage fully
pulled to operator and the upper poles are locked in the
position of the carriage fully pushed forward to the guide
fence (refer to the section titled "Slide lock adjustment".)
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin. (Fig. 54)
Carry the tool by holding both sides of the tool base as
shown in the figure. If you remove the holders, dust bag,
etc., you can carry the tool more easily. (Fig. 55)
Miter angle
(1) Right 45°
(2)
Left 45°
(3)
(4) Right 45°
Finished piece
Save the right side of blade
Save the left side of blade
Save the right side of blade
Save the left side of blade
WARNING:
• Stopper pin is only for carrying and storage pur-
poses and should never be used for any cutting
operations. The use of the stopper pin for cutting oper-
ations may cause unexpected movement of the saw
blade resulting in kickback and serious personal injury.
CAUTION:
• Always secure all moving portions before carrying the
tool. If portions of the tool move or slide while being
carried loss of control or balance may occur resulting in
personal injury.

MAINTENANCE

WARNING:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance. Failure to unplug and switch off the
tool may result in accidental start up of the tool which
may result in serious personal injury.
• Always be sure that the blade is sharp and clean for
the best and safest performance. Attempting a cut
with a dull and/or dirty blade may cause kickback and
result in a serious personal injury.
NOTICE:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
1. Miter angle
Push the carriage toward the guide fence and tighten the
locking screw clockwise and pull the lock lever towards
the front of the saw to secure the carriage.
Turn the grip counterclockwise which secures the turn
base. Turn the turn base so that the pointer points to 0°
on the miter scale. Then turn the turn base slightly clock-
wise and counterclockwise to seat the turn base in the 0°
miter notch. (Leave as it is if the pointer does not point to
0°.) Loosen the hex socket bolts securing the guide fence
using the socket wrench.
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin. Square the side of the
blade with the face of the guide fence using a triangular
rule, try-square, etc. Then securely tighten the hex
socket bolts on the guide fence in order starting from the
right side. (Fig. 56)
Make sure that the pointer points to 0° on the miter scale.
If the pointer does not point to 0°, loosen the screw which
secures the pointer and adjust the pointer so that it will
point to 0°. (Fig. 57)
23