Operation - Makita SP6000 Instruction Manual

Number
1
2
3
4
5
6
CAUTION:
• The speed adjusting dial can be turned only as far as 6
and back to 1. Do not force it past 6 or 1, or the speed
adjusting function may no longer work.
• The speed adjusting dial is not for using low speed
rated saw blades but for obtaining a speed which is
suitable to material of workpiece. Use only saw blades
which are rated for at least 5,200 min
The tools equipped with electronic function are easy to
operate because of the following features.
Overload protector
When the tool is overloaded and current flows above a
certain level, the tool automatically stops to protect motor.
Constant speed control
Electronic speed control for obtaining constant speed.
Possible to get fine finish, because the rotating speed is
kept constant even under load condition.
Soft start feature
Soft start because of suppressed starting shock.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Hex wrench storage (Fig. 18)
Hex wrench is stored on the tool. To remove hex wrench,
just pull it out.
To install hex wrench, place it on the grip and insert it as
far as it will go.
Removing or installing saw blade
CAUTION:
• Do not use saw blades which do not comply with the
characteristics specified in these instructions.
• Use only saw blades which are rated for at least
-1
5,200 min .
• Be sure the blade is installed with teeth pointing up at
the front of the tool.
• Use only the Makita wrench to install or remove the
blade.
To remove the blade, push in the lock-off button to unlock
the upper limit stopper. (Fig. 19)
Turn the locking lever to lock the saw head for replacing a
blade. (Fig. 20)
With the lock-off button depressed and the locking lever
turned, lower the handle so that the lock pin fits in the
groove formed by the locking lever and the depth guide
10
with scale plate. Make sure that the lock pin fits in the
-1
min
groove.
2,000
Press the shaft lock fully so that the blade cannot revolve
2,200 and use the wrench to loosen the hex bolt
counterclockwise. Then remove the hex bolt, outer flange
3,100
and blade. (Fig. 21)
4,000
To install the blade, follow the removal procedure in
4,900
reverse. BE SURE TO TIGHTEN THE HEX BOLT
5,200
CLOCKWISE SECURELY. (Fig. 22)
Connecting a vacuum cleaner (Fig. 23)
When you wish to perform clean cutting operation,
connect a Makita vacuum cleaner to your tool. Connect a
hose of the vacuum cleaner to the dust port as shown in
the figure.

OPERATION

-1
.
Section cutting (ordinary sawing) (Fig. 24)
CAUTION:
• Be sure to move the tool forward in a straight line
• Never approach any part of your body under the tool
Hold the tool firmly. The tool is provided with both a front
grip and rear handle. Use both to best grasp the tool. If
both hands are holding saw, they cannot be cut by the
blade. Set the front of base on the workpiece to be cut
without the blade making any contact. Then push in the
lock-off button and turn the tool on and wait until the blade
attains full speed. Now press down the saw head slowly to
the preset depth of cut and simply move the tool forward
over the workpiece surface, keeping it flat and advancing
smoothly until the sawing is completed.
To get clean cuts, keep your sawing line straight and your
speed of advance uniform. If the cut fails to properly follow
your intended cut line, do not attempt to turn or force the
tool back to the cut line. Doing so may bind the blade and
lead to dangerous kickback and possible serious injury.
Release switch, wait for blade to stop and then withdraw
tool. Realign tool on new cut line, and start cut again.
Attempt to avoid positioning which exposes operator to
chips and wood dust being ejected from saw. Use eye
protection to help avoid injury.
When using with guide rail (accessory)
(Fig. 25 & 26)
Place the tool on the rear end of guide rail. Turn two
adjusting screws on the tool base so that the tool slides
smoothly without a clatter. Hold the tool firmly. The tool is
provided with both a front grip and rear handle. Use both
to best grasp the tool. Turn on the tool, press down the
tool to the preset depth of cut and cut the splinterguard
along the full length with a stroke. The edge of the
splinterguard corresponds to the cutting edge.
When bevel cutting with the guide rail, slide the slide lever
gently. Forcing or twisting the tool will result in
overheating the motor and dangerous kickback,
possibly causing severe injury.
base when section cutting, especially at starting. Doing
so may cause serious personal injuries. The blade is
exposed under the tool base.