GE JKP35 Specification Sheet page 2

27" built-in double ovens
27" built-in double oven dimensions (in inches)
27" models PK956, JKP75, JKP55, JKP35
Locate
10
junction box
for 27"models
either 5" MIN.
below cutout
floor or 44"
MIN. above
cutout floor
D
E
(48-1/2" Long)
2" X 4" or
equiv. runners
Minimum
(cutout floor)
cutout location
from floor
Note: Cabinets installed adjacent to wall ovens must have an adhesion spec of at
least a 194°F temperature rating.
Note: If marks, blemishes or the cutout opening is visible above the installed oven,
it may be necessary to add wood shims under the runners and front trim until the
marks or openings are covered.
Note: Door handle protrudes 3" from door face. Cabinets and drawers on adjacent
45° and 90° walls should be placed to avoid interference with the handle.
27" built-in microwave double oven dimensions (in inches)
Model JKP90
10
Recommended
junction box
locations.
Locate junction
box either 5" MIN.
below cutout
floor or 48" MIN.
above cutout
floor
D
Minimum
E
cutout location
from floor
Note: Door handle protrudes 3" from door face. Cabinets and drawers on adjacent
45° and 90° walls should be placed to avoid interference with the handle.
Note: Cabinets installed adjacent to wall ovens must have an adhesion spec of at
least a 194°F temperature rating.
Note: If marks, blemishes or the cutout opening is visible above the installed oven,
it may be necessary to add wood shims under the runners and front trim until the
marks or openings are covered.
Electric wall ovens are not approved for installation with a plug and receptacle.
They must be hard wired in accordance with installation instructions.
Installation information: Before installing, consult installation instructions
packed with product for current dimensional data.
(continued)
Locate
junction box
for 24"models
56" MIN. above
cutout floor
Allow 3/4"
A
for overlap
over all edges
of cutout
C
B
G
Conduit
F
21" MIN.
door opening
allowance
A
Allow 3/4" for overlap
of oven over all
edges of cutout
C
2" X 4" or
equiv. runners
B
H
G
Conduit
(48-1/2"
F
long)
Allow minimum of
21" for clearance
to adjacent corners,
drawers, walls, etc.
Oven support
for 27" models
to support
Oven support
for 24" models
21
Cabinet
A – Cabinet width required
B – Minimum cabinet depth
C – Opening width
D – Opening height
E – Recommended minimum
cutout location from floor
Oven
F – Overall depth*
G – Overall height with trim
H – Overall width
* Depth including door handle is approximately 26-7/10" min. to
26-8/10" max. on models PK956, JKP75/55/35.
Suitable
to support
21
Cabinet
A – Cabinet width required
B – Minimum cabinet depth
C – Opening width
D – Opening height
E – Minimum cutout location from floor
Oven
F – Overall depth*
G – Overall height
H – Overall width
* Depth including door handle is approximately 26-7/10" min. to 26-8/10" max.
C L
Suitable
bracing
18"
runners
Over centerline
of cabinet
(Must support 300 lbs.)
C L
Suitable
bracing
11"
to support
over centerline
runners of cabinet
(Must support 275 lbs.)
JPK956/JKP75/55/35
27" min.
23-5/8"
25" min. - 25-1/4" max.
50-1/8" max.
13-1/4"
23-5/8"
w/o trim 51"
51-7/8" - 52-3/4"
26-5/8"
C L
bracing
18"
over centerline
runners of cabinet
(Must support 275 lbs.)
w/o trim
with trim
ge.com
2" x 4" or
equivalent
runners
2 x 4 or
equivalent
runners
2 x 4 or
equivalent
runners
27"
27" min.
23-5/8"
25" min. - 25-1/4" max.
41-1/4" max.
22"
23-5/8"
42-1/8"
43" - 43-7/8"
26-5/8"