Performance Features; Vacuum Cleaner - Kenmore 116.21714 Use & Care Manual

ACCESORIOS DEL TUBO
1. Para retirar
los tubos de la
PowerMate,
colóquelos en
la posición
vertical de
bloqueo.
2. Pise el pedal de liberación rápida del tubo
y tire del tubo hacia arriba para desprenderlo
de la PowerMate.
Pedal de
liberación
rápida
del tubo
3. Coloque el accesorio deseado sobre el
tubo. Consulte la CUADRO DE USO DE LOS
ACCESORIOS (pág 16).
Tubo
telescopico
Cepillo para
combinación
Tubo
telescopico
Cepillo para
pelo de animales
Herramienta
para hendiduras
Tubo
telescopico
Tubo
telescopico
Cepillo
para pisos
Pet PowerMate
Wand
NOTA:
Para remover el cepillo de combinación,
presione el botón de liberador del cepillo
y sepárelo.
Botón de liberación
del cepillo
NOTA:
Para remover el cepillo de piso y/o el
cepillo para pelo de mascotas, presione el
botón liberador del accesorio y sepárelo.
Botón de liberación
del accesorio
Botón de liberación
del accesorio
14

PERFORMANCE FEATURES

WARNING
Personal Injury Hazard
Always turn off and unplug the vacuum
cleaner before cleaning the agitator area
as agitator may suddenly restart. Failure
to do so can result in personal injury.
BELT RESET
The PowerMate has built-in protection
against motor and belt damage should the
agitator jam. If the agitator slows down or
stops, the BELT RESET shuts off the
PowerMate and the red belt reset light will
turn on. The canister motor will continue to
run.
BELT RESET
Button
Belt
Reset Light
To correct problem: Turn off and unplug
vacuum cleaner, remove obstruction, then
press BELT RESET button.
If the problem persists, have the vacuum
cleaner serviced by a Sears or other
qualified service agent.
THERMAL PROTECTOR
This vacuum cleaner has a thermal
protector which automatically trips to
protect the vacuum cleaner from
overheating. If a clog prevents the normal
flow of air to the motor, the thermal
protector turns the motor off
automatically. This allows the motor to
cool in order to prevent possible damage
to the vacuum cleaner.
To correct problem: Turn off and unplug
vacuum cleaner to allow the vacuum
cleaner to cool and the thermal protector
to reset. Check for and remove clogs, if
necessary. See REMOVING CLOGS (page
20). Also check and replace any clogged
filters. Wait approximately thirty (30)
minutes and plug the vacuum cleaner in
and turn back on to check if the thermal
protector has reset.
CHECK BAG INDICATOR
When the vacuum cleaner is running with
normal airflow, the CHECK BAG light is
off. The light comes on whenever the
dust bag is full, airflow becomes blocked,
or if there is a clog. If that occurs, first
check the
disposable dust
CHECK BAG
bag. Then check
Indicator
the motor safety
filter and other
possible clog
locations shown in
REMOVING
CLOGS (page 20).
To correct problem: See the TROUBLE-
SHOOTING table (page 29-30).
NOTE: The CHECK BAG indicator light may
come on when using certain attachments,
due to reduced airflow through attachment.
The CHECK BAG indicator light may not
turn on when the vacuum cleaner is used in
low suction power level due to reduced air
power.
POWERMATE STORAGE
The wand has a "U" shaped storage hook
that slides into the "U" shaped slot on the
canister.
The storage hook allows the wands and
PowerMate to be stored with the canister to
conserve storage space. The canister must
be stored on end for this feature to be used.
To attach the
PowerMate, it
Storage
must be in the
Hook
flat position. Use
the handle
release pedal to
place it in this
position.
Slot
The wand will
slip out of the
slot as it is lifted
up for use and
will slide into the
slot as it is
lowered for
storage.
19