HP 6125XLG Configuration Manual page 54

Renumbering the member ID may result in configuration change or loss. Continue? [Y/N]:y
[Sysname] quit
<Sysname> reboot
# Connect Device D to Device B and Device C as shown in Figure 17, and log in to Device D. This
example uses the SFP+ port group that contains Ten-GigabitEthernet 4/1/7, Ten-GigabitEthernet
4/1/8, Ten-GigabitEthernet 4/1/11, and Ten-GigabitEthernet 4/1/12 for IRF connection.
# Shut down the physical ports.
<Sysname> system-view
[Sysname] interface range name irf interface ten-gigabitethernet 4/1/7
ten-gigabitethernet 4/1/8 ten-gigabitethernet 4/1/11 ten-gigabitethernet 4/1/12
[Sysname-if-range-irf] shutdown
[Sysname-if-range-irf] quit
# Bind Ten-GigabitEthernet 4/1/7 and Ten-GigabitEthernet 4/1/8 to IRF-port 4/1.
[Sysname] irf-port 4/1
[Sysname-irf-port4/1] port group interface ten-gigabitethernet 4/1/7
[Sysname-irf-port4/1] port group interface ten-gigabitethernet 4/1/8
[Sysname-irf-port4/1] quit
# Bind Ten-GigabitEthernet 4/1/11 and Ten-GigabitEthernet 4/1/12 to IRF-port 4/2.
[Sysname] irf-port 4/2
[Sysname-irf-port4/2] port group interface ten-gigabitethernet 4/1/11
[Sysname-irf-port4/2] port group interface ten-gigabitethernet 4/1/12
[Sysname-irf-port4/2] quit
# Bring up the SFP+ ports and save the configuration.
[Sysname] interface range name irf
[Sysname-if-range-irf] undo shutdown
[Sysname-if-range-irf] quit
[Sysname] save
# Activate the IRF port configuration.
[Sysname] irf-port-configuration active
Device D reboots to join the IRF fabric. A four-chassis IRF fabric is formed.
5. Configure ND MAD on the IRF fabric:
# Enable the spanning tree feature globally on the IRF fabric to prevent loops.
<Sysname> system-view
[Sysname] stp global enable
# Configure the IRF fabric to change its bridge MAC address as soon as the master leaves.
[Sysname] undo irf mac-address persistent
# Set the domain ID of the IRF fabric to 1.
[Sysname] irf domain 1
# Create VLAN 3, and add Ten-GigabitEthernet 1/1/5, Ten-GigabitEthernet 2/1/5,
Ten-GigabitEthernet 3/1/5, and Ten-GigabitEthernet 4/1/5 to VLAN 3.
[Sysname] vlan 3
[Sysname-vlan3] port ten-gigabitethernet 1/1/5 ten-gigabitethernet 2/1/5
ten-gigabitethernet 3/1/5 ten-gigabitethernet 4/1/5
[Sysname-vlan3] quit
# Create VLAN-interface 3, assign it an IPv6 address, and enable ND MAD on the interface.
[Sysname] interface vlan-interface 3
50