Devices are intended to provide noninvasive ventilatory (niv) support to
treat adult patients weighing over 30 kg (66 lbs) and pediatric patients 7 years or older and weighing over 18 kg (40 lbs) (126 pages)
Table of Contents Intended Use ................................2 Warnings .................................. 2 Cautions ................................... 2 Contraindications ..............................3 Patient Precautions ..............................3 Symbol Key ................................3 System Contents ..............................4 System Overview ..............................4 Control Buttons ..............................5 Available Therapy Features ..........................5 Installing the Air Filters ............................
The BiPAP autoSV Advanced System One is intended to provide non-invasive ventilatory support to treat adult patients (>30 kg/66 lbs) with Obstructive Sleep Apnea and Respiratory Insufficiency caused by central and/or mixed apneas and periodic breathing. This device may be used in the hospital or home.
• Before operating the device, ensure that the SD card cover is replaced whenever any of the accessories such as the Link Module or Modem are not installed. Refer to the instructions that came with your accessory. • Condensation may damage the device. If this device has been exposed to either very hot or very cold temperatures, allow it to adjust to room temperature (operating temperature) before starting therapy.
If any of these items are missing, contact your home care provider. System overview The BiPAP autoSV Advanced System One device is intended to augment your breathing by supplying pressurized air through a circuit. It senses the your breathing effort by monitoring airflow in the circuit and adjusts its output to assist in inhalation and exhalation.
Control Buttons LCD Display Screen Humidifier Icon and Number Settings Control Wheel/Push Button Alarm Silence/Indicator Ramp Button Button This figure shows the primary control buttons on the device, described in the following table. eature eScription Display Screen Shows therapy settings, patient data, and other messages. The startup screen is shown temporarily when the unit is first powered.
installing the air Filters CauTion: A properly installed, undamaged gray foam filter is required for proper operation. The device uses a gray foam filter that is washable and reusable, and an optional white ultra-fine filter that is disposable. The reusable filter screens out normal household dust and pollens, while the ultra-fine filter provides more complete filtration of very fine particles.
navigating the Device Screens Turn the wheel to toggle between options and settings on the screen. Press the wheel to choose an option or setting that is highlighted. If you choose “Back” on any screen, it will take you back to the previous screen. note: The screens shown throughout this manual are examples only.
Monitor Pressure Screen From the Main Menu, if you select Therapy and then press the Wheel, the following Monitor Pressure screen appears. Example shown here. The Monitor Pressure screen displays the following items: Pressure • Timed Breath Indication • I/E State Indication •...
Bi-Flex/Rise time Screen From the Home screen, highlight “Bi-Flex” or “Rise time” and press the wheel. The following screen will appear. note: This screen will be blank on the Home screen if your provider has not enabled Bi-Flex or Rise time on your device. Back Bi-Flex 1 2 3...
• Tubing Type - This setting allows you to select the correct size diameter tubing that you are using with the device. You can choose either “22” for any Respironics 22 mm tubing, or “15” for the optional Respironics 15 mm tubing. If you are using the optional Respironics 15 mm tubing, the device tubing type setting must be set to 15.
note: The screen will only show a few lines at a time. As you rotate the wheel to toggle over different options the screen will slide up and down accordingly. If the text is too long to completely fit on the screen, it will scroll horizontally across the screen when highlighted.
• AHI - The device accumulates individual Apnea/Hypopnea indices (AHI) for each session the patient used the device. This screen displays the average of these individual nightly AHI values over a 7 day and 30 day time frame (provided the device has at least 7 or 30 days of data respectively). If the device has only 5 days of data to use for the calculation, the 5 day average value will be seen under the 7 day display.
alert audible indicators An audible indicator sounds whenever a power failure or a high, medium, or low priority alarm is detected. Additionally, an audible indicator sounds for informational messages and to confirm that certain actions have occurred (for example, when an SD card is inserted or removed from the device). •...
larm riority uDible iSual nDicatorS evice ction ction nDicator High • • • • • Red flashing button; Operates This could be caused by an excessive Pressure “Low Pressure” leak or blockage or a device malfunction. Alarm Press the Alarm Silence/Indicator button to silence the alarm.
larm riority uDible iSual nDicatorS evice ction ction nDicator Low Input Medium • • • Yellow flashing button; Device Operates; The alarm is caused when input power at Voltage “Low Voltage” Humidifier shuts the device, either from an AC outlet or down battery, falls below the acceptable limit for 10 seconds.
Troubleshooting The table below lists some of the problems you may experience with your device and possible solutions to those problems. roblem appeneD hat to Nothing happens when you apply There is no power at the If you are using AC power, check the outlet and verify that the device power to the device.
• Using the SD Card The BiPAP autoSV Advanced System One comes with an SD card inserted in the SD card slot on the back of the device to record information for the home care provider. Your home care provider may ask you to periodically remove the SD card and send it to them for evaluation.
It may be helpful to bring this manual along with you to help security personnel understand the BiPAP autoSV Advanced System One device. If you are traveling to a country with a line voltage different than the one you are currently using, a different power cord or an international plug adaptor may be required to make your power cord compatible with the power outlets of the country to which you are traveling.
Specifications Environmental Operating Temperature: 5° to 35° C (41° to 95° F) Storage Temperature: -20° to 60° C (-4° to 140° F) Relative Humidity (operating & storage): 15 to 95% (non-condensing) Atmospheric Pressure: 101 to 77 kPa (0 - 2286 m / 0 - 7500 ft) Physical Dimensions: 18 x 14 x 10 cm (7”...
Disposal Dispose of this device in accordance with local regulations. How to Contact Respironics To have your device serviced, contact your home care provider. If you need to contact Respironics directly, call the Respironics Customer Service department at 1-800-345-6443 or 1-724-387-4000. You can also use the following addresses: Respironics, Inc.
Limited Warranty Respironics, Inc. warrants that the system shall be free from defects of workmanship and materials and will perform in accordance with the product specifications for a period of two (2) years from the date of sale by Respironics, Inc. to the dealer.
1071073 1070900 R00 JR 12/20/2010 EN-DOM...