Level Dryer - Kenmore Sensor smart electric dryer Use And Care Manual
Hide thumbs
Also See for Sensor smart electric dryer:
- Owner's manual and installation instructions (92 pages) ,
- Use and care manual (48 pages) ,
- Quick start install manual (20 pages)
Table of Contents
Advertisement
Available languages
Available languages
2. Firmly grasp the body of the dryer (not the top or console
panel). Gently lay the dryer on the cardboard.
Examine the leveling legs. Find the diamond marking.
4. Screw the legs into the leg holes by hand. Use a wrench to
finish turning the legs until the diamond marking is no longer
visible.
5. Place a carton corner post under each of the 2 dryer back
corners. Stand the dryer up. Slide the dryer on the corner
posts until it is close to its final location. Leave enough room
to connect the exhaust vent.
6. Once connection is made and dryer is in final location,
remove corner posts and cardboard.
Check the levelness of the dryer. Check levelness first
side to side, then front to back.
If the dryer is not level, prop up the dryer using a wood block.
Use a wrench to adjust the legs up or down and check again for
levelness.
NOTE: It might be necessary to level the dryer again after it is
moved into its final position.
Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in
dryer. If connecting to existing vent, make sure the vent is
clean. The dryer vent must fit over the dryer exhaust outlet
and inside the exhaust hood. Make sure the vent is secured
to exhaust hood with a 4" (10.2 cm) clamp.
2. Move dryer into final position. Do not crush or kink vent.
Make sure dryer is level.
3. (On gas models) Check to be sure there are no kinks in the
flexible gas line.
1. Check to be sure all parts are now installed. If there is an
extra part, go back through the steps to see which step was
skipped.
2. Check to be sure you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Check the dryer's final location. Be sure the vent is not
crushed or kinked.
5. Check to be sure the dryer is level. See "Level Dryer."
Electricam Shock Hazard
Pmug into a grounded
3 prong outlet.
Do not remove ground
prong.
Do not use an adapter,
Do not use an extension
cord,
Faimure to follow
these instructions
can resumt in death,
fire, or eiectricam shock,
6. Plug into a grounded outlet. Turn on power.
7. Remove the blue protective film on the console and any tape
remaining on the dryer.
8. Read "Dryer Use."
9. Wipe the dryer drum interior thoroughly with a damp cloth to
remove any dust.
fg. Set the dryer on a full heat cycle (not an air cycle) for
20 minutes and start the dryer.
If the dryer will not start, check the following:
•
Controls are set in a running or "On" position.
•
Start button has been pushed firmly.
•
Dryer is plugged into a grounded outlet.
•
Electrical supply is connected.
•
House fuse is intact and tight, or circuit breaker has not
tripped.
•
Dryer door is closed.
11. When the dryer has been running for 5 minutes, open the
dryer door and feel for heat.
If you do not feel heat, turn off the dryer and check the
following:
•
There may be 2 fuses or circuit breakers for the dryer.
Check to make sure both fuses are intact and tight, or
that both circuit breakers have not tripped. If there is still
no heat, contact a qualified technician.
NOTE: You may notice a burning odor when the dryer is first
heated. This odor is common when the heating element is first
used. The odor will go away.
Page 15
- Quick Links:
- Troubleshooting
Hide quick links:
Advertisement
Chapters
Table of Contents
