500Kva Ipg - Toshiba G8000 SERIES Installation And Operation Manual

500kVA IPG

TOSHIBA
Installation Planning Guide for 500kVA UPS
Standard System: 480V Input, 480Y/277V Output (P/N T80S3K50KK6XSxx)
Dimensions
Weight
(W x D x H)
Inches
101.8" x 37.4" x 79.7"
Maximum Input Power Demand
Normal Mode (Recharge Mode)
kVA PF
484 (505) >0.99
Alternate (Bypass) AC Input (480V 3-Phase / 4-Wire)
Maximum Input Power Suggested External
Demand Overcurrent Protection
kVA PF Amps
500 0.9 601
DC Capacity for Full
Backup System
Load Output
kWB
Battery 478
* If required. Most Battery and Flywheel Cabinets are equipped with built-in breakers.
Suggested External
Rated Output Power
Overcurrent Protection
kVA PF Amps
500 0.9 601
Important Notes:
1. CABLE ACCESS – Top only.
2. Maximum Current required at Primary AC Input based on full
load output and maximum battery charging current.
3. Output load conductors are to be installed in separate
conduit from input conductors.
4. Control wires and power wires are to be installed in separate
conduits.
5. Recommended AC input and output overcurrent protection
based on continuous full load current per NEC.
6. Wiring shall comply with all applicable national and local
electrical codes.
7. Grounding conductors to be sized per NEC Article 250-122.
Neutral conductors to be sized per NEC Article 310.15.
- Primary AC Input: 3φ, 3-wire + ground.
- Alternate AC Input: 3φ, 4-wire + ground.
- AC Output: 3φ, 4-wire + ground.
- DC Input: 2-wire (Positive/Negative) + ground.
8. Nominal battery voltage based on the use of VRLA type
batteries (2.0 volts/cell nominal).
9. Maximum battery discharge current based on lowest
permissible discharge voltage of 1.67 VPC.
10. DC wires should be sized to allow not more than a 2-volt
drop at maximum discharge current.
11. Weights do not include batteries or other auxiliary equipment
external to the UPS.
Rev. 0.0
G8000 Series Installation and Operation Manual
G8000 Series UPS
General Mechanical Information
Floor Approximate Full-Load
Loading Heat Rejection
2
Lbs. Lbs./ft. Btu/Hr
6520 247 101,490
Primary AC Input (480V 3-Phase / 3-Wire)
Suggested External
Overcurrent Protection
Amps Amps
582 (608) 800 AT
Amps
800 AT (3) x 400 kcmil – (3) x 500 kcmil // (6) x 400 kcmil – (6) x 500 kcmil
DC Backup Input (Battery - 480VDC Nom.)
Maximum Discharge Suggested External
at Full Load Output Overcurrent Protection*
Amps DC
1193
AC Output (480/277V 3-Phase / 4-Wire)
Amps
800 AT (3) x 400 kcmil – (3) x 500 kcmil // (6) x 400 kcmil – (6) x 500 kcmil
12. Cable sizing calculations based on the following assumptions:
13. Ratings of wires and overcurrent devices are suggested
TOSHIBA
13131 West Little York Road
Houston, TX 77041
Telephone: (877) 867-8773
Fax: (713) 896-5212
Web Site:
Page 1 of 3
Mechanical Clearance (Inches)from UPS
for Ventilation and Maintenance Access
Top Front Bottom
15.75" 37" 0"
External Feeder Wire Size: Min. – Max. Per Phase
AWG or kcmil at 75º C Temp. Rating
(3) x 250 kcmil – (3) x 300 kcmil
External Feeder Wire Size:
Min. – Max. Per Phase // Min. – Max. for Neutral
AWG or kcmil at 75º C Temp. Rating
External Feeder Wire Size/pole:
Min. – Max.
Amps AWG or kcmil at 75º C Temp. Rating
1200 A (3) x 400 kcmil – (3) x 500 kcmil
External Feeder Wire Size:
Min. – Max. Per Phase // Min. – Max. for Neutral
AWG or kcmil at 75º C Temp. Rating
- Minimum size is smallest size based on ampacity at 30 °C.
- Maximum size cable is based on cable bend radius limitations at
the UPS terminals.
- Neutral sized for 1.7X phase current.
- Not more than 3 current-carrying conductors installed in conduit
in ambient temperature of 30 °C.
- Temperature rating of copper conductors/terminals: 75 °C.
- Reference: 2005 NEC Handbook, Table 310.16.
NOTE: Consult latest edition of applicable
national and local codes for possible
variations.
minimums. Consult with a registered Professional Engineer within
your local area for proper size selections.
INTERNATIONAL CORPORATION
www.toshiba.com/ind
G8000-IPG-500kVA
Sides Back
0" 0"
97