Download  Print this page

Refrigerator Doors: Removing, Reversing (Optional) And Replacing - Kenmore 2225401 Use & Care Manual

Top-mount refrigerator
Hide thumbs

Advertisement

6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the V4in. drilled hole
in the water pipe and that the washer is under the pipe clamp.
Tighten the packing nut. Tighten the pipe clamp screws
carefully and evenly so washer makes a watertight seal. Do
not overtighten or you may crush the copper tubing.
7. Slip the compression
sleeve and compression
nut on the
copper tubing as shown. Inser[ the end of the tubing into the
outlet end squarely as far as it will go. Screw compression
nut
onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and
turn ON the main water supply. Flush the tubing until water is
clear. Turn OFF the shutoff valve on the water pipe. Coil the
copper tubing.
Connecting
to Refrigerator
1. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression
nut. Do
not overtighten. Use the tube clamp on the back of the
refrigerator to secure the tubing to the refrigerator as shown.
This will help prevent damage to the tubing when the
refrigerator is pushed back against the wall.
2. Turn shutoff valve ON.
3. Check for leaks. Tighten any connections
(including
connections
at the valve) or nuts that leak.
AII:I-
1. Tube Clamp
2. Copper Tubing
3. Compression
Nut
4. Valve Inlet
4. The ice maker is equipped with a built-in water strainer. If
your water conditions require a second water strainer, install it
in the 1/4in. (6.35 mm) water line at either tube connection.
Obtain a water strainer from your nearest appliance dealer.
5. Plug in refrigerator or reconnect power.
Tools required:
5/lein. hex-head socket wrench, No. 2 Phillips
screwdriver, flat-head screwdriver, 5/16 in. open-end wrench, flat 2
in. putty knife.
IMPORTANT:
Before you begin, turn the refrigerator control OFF, unplug
refrigerator or disconnect
power. Remove food and any
adjustable door or utility bins from doors.
If you only want to remove and replace the doors, see the
"Door and Hinge Removal" and "Door and Hinge
Replacement"
sections.
All graphics referenced in the following instructions are
included later in this section after "Final Steps."
Door and Hinge Removal
5/16"Hex-Head Hinge Screw
1*
2.
3.
Unplug refrigerator or disconnect
power.
Open refrigerator door and remove base grille from the
bottom front of the refrigerator (see Base Grille graphic).
Close the refrigerator door and keep both doors closed until
you are ready to lift them free from the cabinet.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
4.
Remove the parts for the top hinge as shown in Top Hinge
graphic. Lift the freezer door free from the cabinet.
5.
Remove the parts for the center hinge as shown in the Center
Hinge graphic. Lift the refrigerator door free from the cabinet.
6.
Remove the parts for the bottom hinge as shown in the
Bottom Hinge graphic.
IMPORTANT: If you want to reverse your doors so that they open
in the opposite direction, follow these steps. If you are not
reversing the doors, see "Door and Hinge Replacement."
6

Advertisement

Table of Contents
loading

  Related Manuals for Kenmore 2225401

  Related Content for Kenmore 2225401

This manual is also suitable for:

106 series