Toshiba B-SA4T Series Option Installation Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Printer
  5. B-SA4T
  6. Option installation manual

Toshiba B-SA4T Series Option Installation Manual

Hide thumbs Also See for B-SA4T Series:
Table of Contents

Advertisement

Quick Links

See also: Product Description
TOSHIBA Thermal Printer
B-SA4T SERIES
Option Installation Manual
Original
Jul., 2005
(Revised
Sep., 2005)
Document No. EO15-33001A
PRINTED IN JAPAN

Advertisement

Table of Contents
loading

Related Manuals for Toshiba B-SA4T Series

Summary of Contents for Toshiba B-SA4T Series

  • Page 1 TOSHIBA Thermal Printer B-SA4T SERIES Option Installation Manual Document No. EO15-33001A Original Jul., 2005 (Revised Sep., 2005) PRINTED IN JAPAN...

  • Page 2: Table Of Contents

    Expansion I/O Board: B-SA704-IO-QM-R ----------------------------------------------------------------- 7- 1 RFID Module: B-SA704-RFID-U2-EU-R -------------------------------------------------------------------- 8- 1 CAUTION! 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC. 2. The contents of this manual may be changed without notification.

  • Page 3: Cutter Module

    INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT WARNING! 1. Turn the printer power off and disconnect the power cord before installing an optional equipment. 2. Be careful not to pinch your fingers or hands with the covers. 3.
  • Page 4 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 2. Open the Front Cover wider. Remove the Front Cover by lifting it to disengage the hinge pins from the hinge. The Front Cover cannot be removed unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement.
  • Page 5 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module Connect the Cutter Harness to the connector at the front of the printer. Connector Cutter Harness Close the Cutter Unit and secure it to the printer with the Set Screw. Set Screw Cutter Unit 7.

  • Page 6: B-Sa204P-Qm-R

    INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 1.2 B-SA204P-QM-R B-SA204P-QM-R is an optional cutter module for the B-SA4TP Series (Plastic cover). CAUTION! Do not connect/disconnect the cutter harness to/from the printer within one minute from a power off to protect the internal electrical circuit of the printer.
  • Page 7 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 3. Mount the Cutter Module Cover by inserting the hinge pins into the hinges. Hinge Cutter Module Cover 4. Fit the Cutter Unit to the front of the printer by inserting the Hinge Pins into the Hinge Pin Holes. Hinge Pin Hinge Pin Hole Hinge Pin...
  • Page 8 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 6. Secure the ground wire of the cutter unit to the printer with the B-3x6 screw removed in Step 1, as shown in the picture. 7. Connect the cutter harness to the connector at the front of the printer. Connector B-3x6 Screw Ground Wire...

  • Page 9: Strip Module

    INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module 2. Strip Module NOTE: Make sure that the firmware version is V1.1 or greater. Firmware V1.0 does not support the strip module. 2.1 B-SA904-H-QM-R B-SA904-H-QM-R is an optional strip module for the B-SA4TM Series (Metal cover). •...
  • Page 10 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 2. Open the Front Cover wider. Remove the Front Cover by lifting it to disengage the hinge pins from the hinge. The Front Cover cannot be removed unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement.
  • Page 11 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 5. Secure the Strip Unit to the printer with the two screws. Make sure that the Feed Roller Gear rotates smoothly. Strip Unit Feed Roller Gear SMW-3x6 Screw 6. Close the Strip Unit. Strip Unit 7.
  • Page 12 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module • Attaching the Cutter The enclosed cutter is used to tear off the batch-issued labels. Attach the cutter with the two SMW-3x6 screws as shown in the picture below. Insert the leading edge of the labels into the opening under the cutter.
  • Page 13 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module • System Mode Settings for Stripping PET Labels When using PET labels on the strip module, please set the following system mode parameters in advance. 1. Connect the printer to a PC. Turn the power ON.
  • Page 14 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module Turn off the printer, and then back to on. (Continued.) Send an issue command to the printer for strip issue. Turn the power OFF. Turn the power ON. Issue labels.
  • Page 15 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module 13. Press the [PAUSE] key repeatedly until Continued. “P.P.FEED” appears on the LCD. PAUSE 14. Press the [FEED] key to feed a label for checking the next label’s stop position. If <2>PARAMETER SET the next label stops with its top edge P.P.FEED...

  • Page 16: B-Sa904P-H-Qm-R

    INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan: 19, 2006) 2. Strip Module 2.2 B-SA904P-H-QM-R B-SA904P-H-QM-R is an optional strip module for the B-SA4TP Series (Plastic cover). • Packing List Strip Unit (1 pc.) Strip Module Cover (1 pc.) SMW-3x6 Screw (4 pcs.) Cutter (1 pc.) Guide Roller (1 pc.)
  • Page 17 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 2. Open the Front Cover wider. Remove the Front Cover by lifting it to disengage the hinge pins from the hinge. The Front Cover cannot be removed unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement.
  • Page 18 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 5. Secure the Strip Unit to the printer with the two screws. Make sure that the Feed Roller Gear rotates smoothly. Strip Unit Feed Roller Gear SMW-3x6 Screw 6. Close the Strip Unit. Strip Unit 7.
  • Page 19 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module • Attaching the Cutter The enclosed cutter is used to tear off the batch-issued labels. Attach the cutter with the two SMW-3x6 screws as shown in the picture below. Insert the leading edge of the labels into the opening under the cutter.

  • Page 20: Wireless Lan Module: B-Sa704-Wlan-Qm

    INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 3. Wireless LAN Module: B-SA704-WLAN-QM 3. Wireless LAN Module: B-SA704-WLAN-QM The pictures used in this section are those of the B-SA4TM, and the installation procedures are common with the B-SA4TP unless otherwise noted. •...
  • Page 21 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 3. Wireless LAN Module: B-SA704-WLAN-QM • Installation Procedure 1. Remove the two SMW-3x6 screws from the back of the printer. Side Panel SMW-3x6 2. Remove the Side Panel in the following order. Please note the procedure is different between the B- SA4TM series and the B-SA4TP series.
  • Page 22 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 3. Wireless LAN Module: B-SA704-WLAN-QM 3. Remove the two SMW-3x6 screws to detach the Blind Plate. Blind Plate SMW-3x6 4. Remove the SMW-3x8 screw to detach the Cable Clamp. Cable Clamp SMW-3x8 Screw 5.
  • Page 23 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 3. Wireless LAN Module: B-SA704-WLAN-QM 6. As the following picture shows, secure the Wireless LAN Board to the printer back with two of the enclosed SMW-3x6 screws. Also, secure the Wireless LAN Board to the PCB Support Plate with the SMW-3x8 screw together with the Cable Clamp removed in Step 4.
  • Page 24 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 3. Wireless LAN Module: B-SA704-WLAN-QM 8. Connect the Wireless LAN Power Cable and the LAN Cable as shown below. CN12 CN17 LAN Cable Wireless LAN Power Cable Fit the Antenna Cover to the back of the printer. Secure it with the SMW-3x6 screw. SMW-3x6 Screw Antenna Cover Pass the LAN Cable through the...
  • Page 25 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 3. Wireless LAN Module: B-SA704-WLAN-QM • Country Code As available frequency bands are different from country to country, be sure to set a country code before installing a wireless LAN module in a user’s printer. Also, ask an end user to confirm a country code. Use of a wireless LAN module with a wrong country code could violate each country’s Laws and Regulations for Radio Equipment, and violators could be subject to penalties.

  • Page 26: Serial Interface Board: B-Sa704-Rs-Qm-R

    INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 4. Serial Interface Board: B-SA704-RS-QM-R The pictures used in this section are those of the B-SA4TM, and the installation procedures are common with the B-SA4TP unless otherwise noted. • Packing List The following parts are supplied with the kit.
  • Page 27 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 2. Remove the Side Panel in the following order. Please note the procedure is different between the B- SA4TM series and the B-SA4TP series. B-SA4TM B-SA4TP (1).Open the Top Cover and Front Cover. Open the Top Cover.
  • Page 28 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 4. Attach the enclosed PCB Support Plate to the printer back with one of the enclosed SMW-3x6 screws. SMW-3x6 PCB Support Plate 5. Fit the Locking Support into the MAIN PC Board. Locking Support MAIN PC Board 6.
  • Page 29 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 7. Secure the SIO PC Board to the printer back with the two SMW-3x6 screws. Fit the Locking Support into the SIO PC Board. SIO PC Board SMW-3x6 Locking Support Re-attach the Side Panel.
  • Page 30 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 5. 300 dpi Print Head Kit: B-SA704-TPH3-QM-R 5. 300 dpi Print Head Kit: B-SA704-TPH3-QM-R B-SA704-TPH3-QM-R is an optional 300 dpi print head kit for the B-SA4TM/SA4TP-GS12 Series (203dpi printer). You will obtain the same print quality as the TS12 model (300 dpi) only by replacing the current print head with this optional kit.

  • Page 31: Installation Procedure

    INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 7. Expansion IO Board: B-SA704-IO-QM-R • Installation Procedure 1. Fully open the Ribbon Cover. 2. Slightly open the Top Cover (10 mm). Ribbon Cover Top Cover 3. Unlock the Print Head by pressing the hooks toward the center. Then pull the Print Head downward. NOTE: Care must be taken not to damage the Print Head Element by hitting it against any metal parts.

  • Page 32: Real Time Clock: B-Sa704-Rtc-Qm-R

    INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 6. Real Time Clock: B-SA704-RTC-QM-R B-SA704-RTC-QM-R is an optional Real Time Clock for the B-SA4TM/SA4TP Series. The pictures used in this section are those of the B-SA4TP, and the installation procedures are common with the B-SA4TM unless otherwise noted.
  • Page 33 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 2. Remove the Side Panel in the following order. Please note the procedure is different between the B- SA4TM series and the B-SA4TP series. B-SA4TM B-SA4TP (1).Open the Top Cover and Front Cover.
  • Page 34 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R NOTES: 1. Place the battery with the “+” mark facing up. 2. A new battery is supposed to last about 2 years or more, but it varies depending on the operating conditions.
  • Page 35 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R Pass the Interface Cable through the Cable Clamp, and between CN1 and CN2 on the MAIN PC Board, as shown in the pictures below. For the B-SA4TP model, wind the cable on the two Cable Clamps.
  • Page 36 B-SA4T V1.2 printer enters the system mode. RESTART NOTE: For details of the system mode, refer to the B-SA4T Series Owner’s Manual stored in <1>RESET the CD-ROM supplied with the printer. When “<1>RESET” is displayed on the LCD, RESTART press the [RESTART] key until “<8>RTC SET”...
  • Page 37 “LOW BATTERY” error and stop at the power on time. In that case, hold down the [RESTART] key to restore to “<1>RESET” display. 3. When “LOW BATTERY” error has occurred, contact the nearest TOSHIBA TEC service representative for replacement of the battery.

  • Page 38: Expansion I/O Board: B-Sa704-Io-Qm-R

    INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 7. Expansion I/O Board: B-SA704-IO-QM-R 7. Expansion I/O Board: B-SA704-IO-QM-R B-SA704-IO-QM-R is an optional expansion I/O board for the B-SA4TM/SA4TP Series. The pictures used in this section are those of the B-SA4TP, and the installation procedures are common with the B-SA4TM unless otherwise noted.
  • Page 39 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 7. Expansion I/O Board: B-SA704-IO-QM-R 2. Remove the Side Panel in the following order. Please note the procedure is different between the B- SA4TM series and the B-SA4TP series. B-SA4TM B-SA4TP (1).Open the Top Cover and Front Cover.
  • Page 40 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 7. Expansion I/O Board: B-SA704-IO-QM-R 4. Attach the Expansion I/O Board to the printer back with one of the supplied SMW-3x6 screws. SMW-3 6 Screw Expansion I/O Board 5. Connect the Interface Cable to CN4 on the MAIN PC Board. CN4 Connector Expansion I/O Board MAIN PC Board...

  • Page 41: Rfid Module: B-Sa704-Rfid-U2-Eu-R

    1. To use this device firmware V1.6 or greater is required. Upgrade the firmware to V1.6 or greater, if necessary. For the downloading procedure, refer to the B-SA4T Series System Mode Manual. 2. The countries where the use of this device is allowed are as follows:...
  • Page 42 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R • Packing List All the following parts are supplied with the kit. Make sure you have all items shown below. Parts (Quantity) Parts (Quantity) Parts (Quantity) Antenna Ass’y (1 pc.) RFID Module (1 pc.) Antenna Cable (1 pc.)
  • Page 43 RFID module by using an RFID Parameter Set Command ([ESC]Z2;3) or printer system mode, respectively. For details of the commands, refer to the B-SA4T Series External Equipment Interface Specification. (6) Try tag read/write with an application.
  • Page 44 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Remove the Side Panel in the following order. Please note the procedure is different between the B- SA4TM series and the B-SA4TP series. B-SA4TM B-SA4TP 1.
  • Page 45 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Slightly push the Upper Sensor Lever inside (1), and open the Upper Sensor Ass’y (2). Upper Sensor Ass’y Upper Sensor Lever Pushing the tabs on the rear of the Media Sensor Block toward the front of the printer, slightly lift the back of the Media Sensor Block, and remove it toward the printer back.
  • Page 46 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R As the following picture shows, pass the Interface Cable through the opening behind the Stepping Motor so that the cable reaches the Main PC Board. Opening Interface Cable Stepping Motor...
  • Page 47 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Fit the supplied Edge Guards on the metal plate all the way to their bottoms. • Please be careful not to injure your hands while fitting the Edge Guards. •...
  • Page 48 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 12. Connect the Interface Cable to the RFID Module. Interface Cable RFID Module 13. Secure the RFID Module to the printer with a supplied Double Sems Screw. Double Sems Screw M-3x6 RFID Module...
  • Page 49 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 15. Re-place the Media Sensor Block. Media Sensor Block 16. Connect the Antenna Cable to the Antenna Ass’y until it clicks, and fasten the Antenna Cable with the Cable Clamp, as shown below.
  • Page 50 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Insert the Shield Sheet, without the backing paper removed, under the Media Guides from behind, and slightly slide it toward the Platen. Then, move the Media Guides to the width of the Shield Sheet (shorter width), as the pictures show.
  • Page 51 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R • RFID Module Settings After installing the RFID Module on the printer, configure the RFID module settings using the system mode on the printer. Turn on the printer while holding down the [FEED] and [PAUSE] keys at the same time.
  • Page 52 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Continued from the previous page. <10>RFID RFID tag type setting menu is displayed. TAG NONE Choose “EPC C1 Gen2: 24” with the [FEED] or [RESTART] key. [RESTART] NONE: When a tag type is not selected.
  • Page 53 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Continued from the previous page. Read retry timeout setting menu is displayed. <10>RFID Set the timeout period during which RFID tag read retries are allowed, with the [FEED] or R CYCLE TIM [RESTART] key.
  • Page 54 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Continued from the previous page RFID adjustment for retry menu is displayed. <10>RFID If writing data on a tag failed, the printer feeds the RFID tag forward or backward for ADJ RETRY specified length in order to retry writing data.
  • Page 55 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Continued from the previous page. Q value setting menu is displayed. <10>RFID Q VALUE In the case multiple RFID tags are read at the same time, this menu is useful to pinpoint a target tag.
  • Page 56 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R • AGC Threshold Setting The B-SA704-RFID-U2-EU-R chooses a tag to write data on according to a radio intensity of RFID tags (AGC value). An AGC threshold value has been set to 11 (0Bh) as factory default, but it may be necessary to change this value according to the tag type to be used.
  • Page 57 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Continued from the previous page Read data is displayed. 3132333435363738 39304142 (0A) Data in parentheses ( ) is the AGC value expressed in hex. code. [FEED], [RESTART] Write down this value.
  • Page 58 • Identification of The Rfid Module (B-SA704-RFID-U2-EU-R) As from the production manufactured in October 2008, the standard label has been added to the RFID module, which is used for the B-SA4T series, for improving the efficiency of assembly. RFID Module Service No.

This manual is also suitable for:

B-sa4tm seriesB-sa4tp series

Table of Contents