Renault Scenic Handbook
Hide thumbs Also See for Scenic:
Table of Contents

Advertisement

SCENIC
DRIVER'S HANDBOOK

Advertisement

Table of Contents
loading

Summary of Contents for Renault Scenic

  • Page 1 SCENIC DRIVER’S HANDBOOK...
  • Page 2 Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please ELF has developed a complete range of lubricants for RENAULT: refer to your maintenance document. engine oils manual and automatic gearbox oils Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
  • Page 3: Driving

    This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.
  • Page 5: Table Of Contents

    Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
  • Page 7 Section 1: Getting to know your vehicle RENAULT cards: general information, use, deadlocking ....... . .
  • Page 8: Doors

    (refer to the information for a short while. by the word “SERVICE” engraved on on the “RENAULT card: battery” in sec- They may pose a risk to themselves the card. Refer to the information on tion 5).
  • Page 9 Replacement: need for an Using the key additional RENAULT card Refer to the information on “Locking/ If you lose your RENAULT card or unlocking the doors”. require another, you can obtain one Once you have accessed the vehicle from an approved dealer.
  • Page 10: Luggage Compartment

    If a door or the luggage compartment is open RENAULT card not detected or not properly shut, or if a RENAULT alarm card is still in the reader, the doors and If a door is opened when the engine...
  • Page 11: Unlocking The Vehicle

    With the RENAULT card in zone 1, the functions of the remote control place your hand on a door handle 2: the RENAULT card, it can be used to lock vehicle will unlock (in some cases, you and unlock without using the RENAULT may need to pull door handle 2 twice to card, when it is in access zone 1.
  • Page 12: Locking The Vehicle

    Note: a RENAULT card must be within the vehicle's access zone (zone 1) to be able to lock the vehicle using the button.
  • Page 13 After locking/unlocking the vehicle or the tailgate only using the but- tons on the RENAULT card, remote locking and unlocking in hands-free mode are deactivated. To reactivate the hands-free mode: restart the vehicle.
  • Page 14 RENAULT cARd: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. The hazard warning lights flash once to indicate that the doors have been un- locked. To activate deadlocking If the vehicle is equipped with a dead-...
  • Page 15 RENAULT “sERVIcE” cARd deactivation of the “sERVIcE” mode There are two possibilities: – press a button on the RENAULT card (not the RENAULT “SERVICE” card); – start the engine with a RENAULT card (not the RENAULT “SERVICE” card). With the card in reader 3, press button 1.
  • Page 16 Pull on the handle 2. With the doors unlocked or the After switching off the engine, the lights RENAULT “hands-free” card in your and any accessories that are in opera- Lights-on reminder buzzer possession, hold handle 1 and pull it to- tion (radio, etc.) will continue to oper-...
  • Page 17: Child Safety

    OpENINg ANd cLOsINg ThE dOORs (2/2) safety of rear occupants The driver can authorise operation of the rear doors and, depending on the ve- hicle, the electric windows by press- ing switch 3 on the side with the il- lustration. Depending on the vehicle, in the event of a fault: –...
  • Page 18: Locking/Unlocking Doors

    LOcKINg/UNLOcKINg ThE dOORs (1/2) Locking/Unlocking the doors from the outside This is done using the RENAULT Card; see the “RENAULT Card” information in Section 1. In certain cases, the RENAULT card may not work: – when the RENAULT card battery is drained, flat battery, etc.
  • Page 19 Unlocking the vehicle from the outside is only possible with the RENAULT card in the vehicle's access zone or using Interior locking/unlocking the key integrated in the RENAULT card.
  • Page 20: Automatic Locking When Driving

    AUTOmATIc LOcKINg WhEN dRIVINg Activating/deactivating the Operating faults function If you experience an operating fault (no To activate: with the vehicle stopped automatic locking, the indicator light in- and the engine running, press switch 1 corporated in button 1 does not light up until a beep sounds.
  • Page 21: Front Headrests

    fRONT hEAdREsTs To adjust side supports B Depending on the vehicle, sections B can be adjusted independently to the desired position. To remove the headrest Raise it to its highest position (tilt the seatback backwards if necessary). Press button 1 on each rod 3 and lift it until it is released.
  • Page 22 fRONT sEATs WITh mANUAL cONTROL (1/2) To move the seat forwards or To tilt the seatback back Turn control knob 3 to the required po- sition. Lift handle 1 to release. Release the For safety reasons, make handle at the desired position and these adjustments only make sure that it is locked.
  • Page 23: Heated Seats

    fRONT sEATs WITh mANUAL cONTROL (2/2) Table function heated seats When the front seat is in (depending on vehicle) table position, the front pas- Depending on the vehicle, the passen- senger air bag must be dis- ger seatback may be folded down onto With the engine running, turn control 6 abled (see information on the seat base to create a table.
  • Page 24: Adjusting The Lumbar Support

    dRIVER’s sEAT WITh ELEcTRIc cONTROLs Switch 4 is used for adjusting the seat base and switch 3 is used for adjusting the seatback. On equipped vehicles, buttons 2 store the chosen driving posi- tion (refer to the following page). Adjusting the seat position To move the seat forwards or back Move switch 4 forwards or backwards.
  • Page 25 – with the “hands-free” card de- recall a driving position. tected or, depending on the vehicle, RENAULT card in the card reader; – when the driver’s door is opened. storing your driving position – Adjust the seat using switches 4 and 5 (see previous page);...
  • Page 26: Seat Belts

    sEAT BELTs (1/3) Before starting, first adjust your driv- Always wear your seat belt when trav- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
  • Page 27 sEAT BELTs (2/3) ß driver’s seat belt reminder and, depending on the vehi- cle, front passenger seat belt re- minder This lights up on the instrument panel when the engine is started, then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approxi- mately 12 mph (20 km/h), it flashes and...
  • Page 28 sEAT BELTs (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
  • Page 29: Rear Seat Belts

    REAR sEAT BELTs second row centre rear seat Unwind belt 2 slowly from its housing. On equipped vehicles, for your com- fort, you can pass the belt through belt guide 3. Click buckle 4 into black catch 5. Snap last sliding buckle 6 into the red catch 7.
  • Page 30: Restraint To Front Seat Belts

    mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (1/4) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretension- an accident. ers; – No operation whatso- –...
  • Page 31: Methods Of Restraint In Addition To The Front Seat Belts

    mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (2/4) Load limiter Air bags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at The presence of this equipment is in- an acceptable level.
  • Page 32 mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (3/4) Operation special feature of the front air This system is only operational when the ignition is switched on. After a violent impact, it has two deploy- ment volumes and integrates a ventila- In a severe frontal impact, the air bags tion system: inflate rapidly, cushioning the impact...
  • Page 33 mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
  • Page 34 mEThOds Of REsTRAINT IN AddITION TO ThE REAR sEAT BELTs force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
  • Page 35 sIdE pROTEcTION dEVIcEs side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the oc- cupants in the event of a severe side impact. curtain air bags These are air bags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear side windows...
  • Page 36: Additional Methods Of Restraint

    AddITIONAL mEThOds Of REsTRAINT All of the warnings below are given so that the air bag is not obstructed in any Operating faults way when it is inflated and also to prevent the risk of serious injuries caused å by items which may be dislodged when the air bag inflates. This warning light comes on when the engine is started and then The air bag is designed to complement the action of the seat belt.
  • Page 37: Child Safety: General Information

    chILd sAfETY: general information (1/2) carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- driver’s responsibility ished growing.
  • Page 38 chILd sAfETY: general information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
  • Page 39 chILd sAfETY: choosing a child seat Rear-facing child seats forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
  • Page 40: Choosing A Child Seat Mounting

    chILd sAfETY: choosing a child seat mounting (1/2) Attachment using the ISOFIX There are two ways of attaching child Before using an ISOFIX seats: via the seat belt or using the system child seat that you pur- ISOFIX system. Authorised ISOFIX child seats are ap- chased for another vehicle, proved in accordance with regulation check that its installation is...
  • Page 41 chILd sAfETY: choosing a child seat mounting (2/2) The rings are located on the floor and indicated by markings on the luggage compartment carpet. To access these anchoring points, push the rear seat forward and lift the cover if necessary. Note: for 7-seater vehicles, the rings are located on the luggage compart- ment floor and are visible.
  • Page 42: Fitting A Child Seat

    chILd sAfETY: fitting a child seat (1/11) In the front seat Some seats are not suitable for fitting child seats. The diagram on the follow- The laws concerning children travel- ing page shows you how to attach a ling in the front passenger seat differ in child seat.
  • Page 43 chILd sAfETY: fitting a child seat (2/11) In the rear seat In the rear centre seat When fitting a child seat A carrycot can be installed across the Some child seats are too wide to allow (Group 2 or 3 booster seat), vehicle and will take up at least two access to the seat belt buckles.
  • Page 44 chILd sAfETY: fitting a child seat (3/11) child seat attached using the IsOfIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.
  • Page 45 chILd sAfETY: fitting a child seat (4/11) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. seat size Weight of front passenger Rear centre Type of child seat Rear side seats the child seat (1) (5)
  • Page 46 chILd sAfETY: fitting a child seat (5/11) child seat attached using the IsOfIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.
  • Page 47 chILd sAfETY: fitting a child seat (6/11) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. seat size Weight of front passenger Rear centre Type of child seat Rear side seats the child seat (1) (5)
  • Page 48 chILd sAfETY: fitting a child seat (7/11) child seat attached using the IsOfIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted.
  • Page 49 chILd sAfETY: fitting a child seat (8/11) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. front seat size Weight of Row 2 rear Row 2 rear Row 3 rear Type of child seat passenger...
  • Page 50 chILd sAfETY: fitting a child seat (9/11) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUf/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal”...
  • Page 51 chILd sAfETY: fitting a child seat (10/11) child seat attached using the IsOfIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.
  • Page 52 chILd sAfETY: fitting a child seat (11/11) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. seat size Weight of front passenger Type of child seat Rear side seats the child seat (1) (5)
  • Page 53: Deactivating/Activating The Front Passenger Airbag

    chILd sAfETY: deactivating/activating the front passenger air bag (1/3) The front passenger air bag must only be deactivated or activated when the vehicle is stationary. If it is interfered with when the ve- hicle is being driven, indicator lights å ©...
  • Page 54 chILd sAfETY: deactivating/activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. dANgER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER...
  • Page 55 chILd sAfETY: deactivating/activating the front passenger air bag (3/3) Operating faults It is not permitted to fit a rear-facing child seat to the front passenger seat if the air bag activation/deactivation system is faulty. It is not recommended to allow any other passenger to sit in that seat if the ›...
  • Page 56: Driving Position

    dRIVINg pOsITION: LEfT-hANd dRIVE (1/2) 1 2 3 5 6 7 8 10 11 1.50...
  • Page 57 3 Stalk for: 19 Gear lever. switch. – direction indicator lights; 11 Location for radio, navigation 20 RENAULT card reader. – exterior lights; system, etc. 21 Cruise control/speed limiter control. – front fog lights; 12 – Display of the time, tempera- 22 Heating and ventilation controls.
  • Page 58 dRIVINg pOsITION: RIghT-hANd dRIVE (1/2) 14 15 1.52...
  • Page 59 21 Electronic parking brake control. 12 Location for driver’s air bag and information, navigation system in- horn. 22 RENAULT card reader. formation, etc. 13 – Steering column stalk for wind- 23 Gear lever. – Driver and front passenger seat...
  • Page 60 INsTRUmENT pANEL: warning lights (1/5) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRY. Φ speed limiter and cruise control indicator lights See the information on the “Speed lim- iter” and “Cruise control” in Section 2. ®...
  • Page 61 INsTRUmENT pANEL: warning lights (2/5) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRY. Ä Toxic fume filter system Warning Light This lights up when the ignition is switched on and goes out when the engine is started.
  • Page 62 INsTRUmENT pANEL: warning lights (3/5) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRY. å handbrake “on” or elec- Rear seat belt reminder (depending Airbag warning light tronic parking brake warn- on vehicle) This lights up when the engine ß...
  • Page 63 INsTRUmENT pANEL: warning lights (4/5) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRY. Warning light It requires you to stop immediately, © for your own safety, as soon as traf- This lights up when the ignition fic conditions allow.
  • Page 64 INsTRUmENT pANEL: warning lights (5/5) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRY. À  The following warning lights come Oil pressure warning light Lane departure warning ® system (continuous on accompanied by the warn- This lights up when the ignition broken line) warning light...
  • Page 65 dIspLAYs ANd INdIcATORs (1/4) Rev counter (rpm × 1,000) This is displayed according to how the instrument panel is customised. speedometer (km/h or mph) fuel gauge The remaining fuel level is shown in yellow. If the level is at the minimum, the warning light integrated in the indicator comes on, accompanied by a beep.
  • Page 66 dIspLAYs ANd INdIcATORs (2/4) Instrument panel in miles Overspeed buzzer (option to switch to km/h) Depending on the vehicle and country, – With the ignition off, press button 3 a buzzer sounds for approximately 10 or 4 and start button 5; seconds every 40 seconds, as long as the vehicle is travelling in excess of 72 –...
  • Page 67: Instrument Panel

    dIspLAYs ANd INdIcATORs (3/4) Vehicle without “TfT display” fuel level gauge 6 Overspeed buzzer instrument panel Depending on the vehicle and country, If the level is at the minimum, the a buzzer sounds for approximately 10 warning light integrated in the indicator Instrument panel B seconds every 40 seconds, as long as comes on, accompanied by a beep.
  • Page 68 dIspLAYs ANd INdIcATORs (4/4) Instrument panel in miles Engine oil level low warning (option to switch to km/h) When the engine is started, the instru- – With the ignition off, press button 3 ment panel display alerts you when the or 4 and start button 5.
  • Page 69: Vehicle Settings Customisation Menu

    TRIp cOmpUTER: general information (1/2) c) mileage before service; d) tyre pressure monitor; e) cruise control/speed limiter pro- grammed speed (only for vehicles which are not equipped with a “TFT Display” instrument panel); f) on-board log, operating fault and in- formation message readout.
  • Page 70: Journey Record

    ON-BOARd cOmpUTER: general information (2/2) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption and average speed will become more stable and reliable the further you have travelled since the last...
  • Page 71 TRIp cOmpUTER ANd WARNINg sYsTEm: journey parameters (1/4) The display of information shown below dEpENds ON ThE VEhIcLE EQUIpmENT ANd cOUNTRY. Examples of selections Interpreting the display selected a) Total mileage and trip mileage recorder. Fuel used b) Journey parameters. fuel used.
  • Page 72 TRIp cOmpUTER ANd WARNINg sYsTEm: journey parameters (2/4) The display of information shown below dEpENds ON ThE VEhIcLE EQUIpmENT ANd cOUNTRY. Examples of selections Interpreting the display selected Range Estimated range with remaining fuel. The value is displayed after driving 400 metres. 541km Distance distance travelled since the last reset.
  • Page 73 TRIp cOmpUTER ANd WARNINg sYsTEm: journey parameters (3/4) The display of information shown below dEpENds ON ThE VEhIcLE EQUIpmENT ANd cOUNTRY. Examples of selections Interpreting the display selected c) mileage before oil change. Oil change in Distance remaining until the next oil change (displayed in miles/kilometres and months), then when the time nears, several scenarios are possible: 1936 km/2 mo.
  • Page 74 TRIp cOmpUTER ANd WARNINg sYsTEm: journey parameters (4/4) The display of information shown below dEpENds ON ThE VEhIcLE EQUIpmENT ANd cOUNTRY. Examples of selections Interpreting the display selected d) Tyre pressure monitor. Refer to the information on the “Tyre pressure monitor” in Section 2. Speed limiter 90.km/H e) cruise control/speed limiter programmed speed (only for vehicles which are...
  • Page 75: Steering Wheel

    “parking brake on” Indicates that the parking brake has been applied. “please remove keycard” Request to remove the RENAULT card from the reader when you leave the vehicle. “checking control Displayed with the ignition on when the vehicle is running self-diagnostics.
  • Page 76 TRIp cOmpUTER ANd WARNINg sYsTEm: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
  • Page 77 TRIp cOmpUTER ANd WARNINg sYsTEm: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf- fic conditions allow. stop your engine and do not restart it. contact an approved dealer. Examples of warning messages are given in the following pages.
  • Page 78 VEhIcLE sETTINgs cUsTOmIsATION mENU Adjusting the settings Once the function has been selected, activate or deactivate it using button Depending on the vehicle equipment, “OK” 2: press button 3 or 4 to select the func- tion to be modified: function activated a) Auto door locking while driving;...
  • Page 79: Power-Assisted Steering

    sTEERINg WhEEL/pOWER-AssIsTEd sTEERINg power-assisted steering Operating faults The steering may become stiff when Variable power-assisted steering driving or when the steering wheel is The variable power-assisted steering turned repeatedly. This is due to the system is equipped with an electronic power assistance overheating.
  • Page 80: Clock And Exterior Temperature

    cLOcK ANd EXTERIOR TEmpERATURE (1/2) Vehicles fitted with a navigation system For vehicles which are fitted with this equipment, please refer to the specific equipment instructions for details of their special features. Resetting the clock 1 Vehicles fitted with control 3 –...
  • Page 81 cLOcK ANd EXTERIOR TEmpERATURE (2/2) External temperature indicator special note: When the exterior temperature is - 3 °C to + 3 °C, the °c characters flash (sig- nalling a risk of ice on the road). External temperature indicator As ice formation is related to climatic exposure, local air humidity and temperature, the external temperature alone is not...
  • Page 82: Rear-View Mirrors

    REAR VIEW mIRRORs folding door mirrors The door mirrors automatically fold in when the vehicle is locked (switch 2 in position D). In this case, they will fold out when the ignition is next switched In any case, you can make the door mirrors fold in (switch 2 in position E) or out (switch 2 in position C).
  • Page 83: Audible And Visual Signals

    AUdIBLE ANd VIsUAL sIgNALs direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0.
  • Page 84: Exterior Lighting And Signals

    EXTERIOR LIghTINg ANd sIgNALs (1/5) main beam headlights á With the dipped beam head- lights lit, pull stalk 1 towards you. This indicator light on the instrument panel comes on. To return to the dipped headlight posi- tion, pull stalk 1 towards you again. side lights dipped beam headlights...
  • Page 85 EXTERIOR LIghTINg ANd sIgNALs (2/5)  Automatic main beam Activation Operating faults headlights Turn ring 3 until the AUTO symbol is op- When the message “Check main beam posite mark 2. lights” appears on the instrument panel, This system switches the main beam Pull stalk 1 to activate main beam the system is deactivated.
  • Page 86: Daytime Running Lights

    EXTERIOR LIghTINg ANd sIgNALs (3/5) directional headlights Operating faults When the message “Check lighting”, Depending on the vehicle, with the © accompanied by the warning dipped beam headlights on and under certain conditions (speed, steering light is displayed on the instrument panel, there is a lighting fault.
  • Page 87 EXTERIOR LIghTINg ANd sIgNALs (4/5) “see-me-home lighting” Lights-on reminder buzzer function If the lights are on after the engine is switched off, a warning beep sounds This function allows you to briefly switch when the driver’s door is opened to on the dipped beam headlights (to pro- warn you that the lights are still on.
  • Page 88: Rear Fog Light

    EXTERIOR LIghTINg ANd sIgNALs (5/5) front fog lights switching off the lights Turn centre ring 5 on stalk 1 Turn ring 5 again until mark 4 is oppo- until the symbol faces mark 4, then re- site the symbol for the fog light that you lease it.
  • Page 89 ELEcTRIcAL AdJUsTmENT Of ThE dIppEd BEAm hEAdLIghTs for manual settings Examples of positions for adjusting control A according to the load driver alone or with front passenger driver with one front passenger and one rear passenger On vehicles fitted with this function, control A allows you to adjust the height of the beams according to the load.
  • Page 90: Windscreen Wipers

    WINdscREEN WIpER, WAshER ( Vehicle fitted with front windscreen wiper rain sensor A park B automatic wiper function When this position is selected, the system detects water on the wind- screen and triggers the wipers at a suitable wiping speed. It is possi- ble to change the triggering thresh- old and the time sweeps by turning ring 2:...
  • Page 91: Headlight Washers

    WINdscREEN WIpER, WAshER ( headlight washers headlights on On equipped vehicles, hold stalk 1 Do not try to lift the wiper blades. pulled towards you for about 1 second, They cannot remain detached from and the headlight washers and wind- the windscreen.
  • Page 92: Rear Screen Wiper

    REAR scREEN WAsh/WIpE Activating/deactivating the rear screen wiper (depending on the vehi- cle) If your vehicle is fitted with a vehicle settings customisation menu, it is pro- grammed to activate the rear wipers when reverse gear is selected (if the windscreen wipers are on).
  • Page 93: Fuel Grade

    fUEL TANK (1/3) fuel grade Vehicles running on ethanol- based fuel Use a high-grade fuel that complies with the legislation in force in each It is essential to use unleaded petrol or country and which must conform to fuel containing a maximum of 85% eth- the specifications given on the label on anol (E85).
  • Page 94 fUEL TANK (2/3) filling with fuel With the ignition off, insert the nozzle to open valve A and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position through- out the entire filling operation.
  • Page 95 fUEL TANK (3/3) Running out of fuel on diesel versions (depending on vehicle) After a breakdown caused by com- pletely running out of fuel, the system must be reprimed before the engine is No modifications what- restarted: soever are permitted on Fill the tank with at least 8 litres of any part of the fuel supply diesel fuel.
  • Page 96 1.90...
  • Page 97 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Starting/Stopping the engine .
  • Page 98: Running In

    RUNNING IN Petrol version Diesel version Up to 600 miles (1,000 km), do not For the first 900 miles (1,500 km), do exceed 78 mph (130 km/h) in top gear not exceed 2,500 rpm. After completing or 3,000 to 3,500 rpm. this mileage you may drive faster, how- ever, it is only after approximately 3600 You may only expect top performance...
  • Page 99: Starting/Stopping The Engine

    2 or in detection zone 3. When you get into the vehicle, insert the In this case, the RENAULT card must RENAULT card fully into card reader 2. To start, depress the brake or clutch not be located in the luggage compart- pedal and press button 1.
  • Page 100 In certain cases, the RENAULT “hands- ReNaULt card, insert the card into free” card may not work: reader 2; – when the RENAULT card battery is – vehicles with a ReNaULt “hands- drained, flat battery, etc. free” card, with the card in the pas- –...
  • Page 101: Special Note

    If the card is no longer in the reader cle, especially if you have when you try to switch the engine off, your RENAULT card with the message “No keycard Press and you, check that the engine hold” appears on the instrument panel: is completely switched off.
  • Page 102: Stop And Start Function

    StoP aND StaRt fUNCtIoN (1/3) This system enables a reduced fuel Special feature of the automatic  consumption and lower greenhouse engine re-start Warning light is displayed on the gas emissions. instrument panel. This notifies you that Under certain conditions, the engine The system is activated automatically the engine is on standby.
  • Page 103 StoP aND StaRt fUNCtIoN (2/3) Conditions preventing the Special cases – the “Clear View” function is activated (please see “Automatic Climate standby of the engine – While the system is operating, and Control” in Section 3); the engine is stopped (traffic jam, Certain conditions prevent the system –...
  • Page 104 StoP aND StaRt fUNCtIoN (3/3) operating faults The system is automatically reactivated each time the vehicle is started using When the message “Check Stop & the start button (please see “Starting, Start” appears on the instrument panel stopping the engine)”. and the integrated warning light 2 lights up on the switch 1, the system is deac- tivated.
  • Page 105: Special Features Of Petrol Versions

    SPeCIaL featUReS of PetRoL veRSIoNS The following operating conditions If you notice any of the above operating should be avoided: faults, have the necessary repairs car- ried out as soon as possible by an ap- – driving for long periods when the low proved dealer.
  • Page 106: Special Features Of Diesel Versions

    SPeCIaL featUReS of DIeSeL veRSIoNS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.
  • Page 107: Gear Lever/Handbrake

    GeaR LeveR/haNDbRake handbrake to release: Pull lever 2 up slightly, press button 3 and then lower the lever to the floor. to apply: Pull the lever 2 upwards and make sure the vehicle is immobilised. Make sure that the hand- Selecting reverse gear brake is properly released when driving (red indicator...
  • Page 108: Electronic Parking Brake

    eLeCtRoNIC PaRkING bRake (1/3) Note: To indicate that the electronic parking brake is applied or released, a beep sounds and the message “Apply park- ing brake” appears on the instrument panel: – with the engine running: when the driver’s door is opened; –...
  • Page 109: Manual Operation

    3 at the same time; You can control the electronic parking To manually activate the electronic – remove the RENAULT card from the brake manually. parking brake, (when stopping at a red card reader. light, or stopping when the engine is applying the electronic parking running, etc.): pull and release switch 3.
  • Page 110 eLeCtRoNIC PaRkING bRake (3/3) versions with an automatic operating faults – If there is an electronic parking brake ® fault, warning light lights up gearbox © – If there is a fault, the warning accompanied by the “Parking brake light on the instrument panel lights For safety reasons, automatic release fault”...
  • Page 111: Engine Adjustments

    aDvICe: antipollution, fuel economy and driving (1/3) aiding fuel economy Your vehicle complies with criteria for Have your vehicle adjusted and recycling and recovering vehicles at the checked by an approved Dealer, in ac- Depending on the vehicle, in order to end of their service life which will come cordance with the instructions given in optimise consumption, an indicator light...
  • Page 112 aDvICe: antipollution, fuel economy and driving (2/3) exhaust gas monitoring – Sporty driving uses a lot of fuel: drive with a light right foot. system – Brake as little as possible. If you an- The exhaust gas monitoring system will ticipate an obstacle or bend in ad- detect any operating faults in the vehi- vance, you may then simply release...
  • Page 113 aDvICe: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
  • Page 114: Environment

    This commitment is illustrated by the less fuel (eg. 140 g/km, equivalent to the vehicle components have been de- Renault eco² group signature. 5.3 l/100 km for a diesel vehicle). signed to enable them to be recycled. Our vehicles are also equipped with a...
  • Page 115 tyRe PReSSURe MoNItoR (1/4) the tyre pressures must be adjusted If the vehicle is equipped with the func- tion, this system monitors the tyre pres- when cold (refer to the label located on sure. the edge of the driver’s door). If tyre pressures cannot be checked when the tyres are cold, the recom- operating principle...
  • Page 116 tyRe PReSSURe MoNItoR (2/4) “tyre pressure sensors absent” or “Check tyre pressure sensors” One wheel B disappears, indicating that the sensor on this wheel is missing or faulty (e.g. if the emergency spare wheel is fitted). vehicles without “tft “Inflate tyres for motorway” The tyre pressure is not suitable for the display”...
  • Page 117 tyRe PReSSURe MoNItoR (3/4) “Inflate tyres for motorway” The wheel concerned E is shown in orange on display 4. The tyre pres- sure is not suitable for the speed of travel. Slow down or inflate all four tyres to motorway pressure (refer to the information on “Tyre pressures”...
  • Page 118 tyRe PReSSURe MoNItoR (4/4) Replacing wheels/tyres tyre repair product and This system requires specific equip- inflation kit ment (wheels, tyres, hubcaps, etc.). Because the valves are specially de- Contact an approved Dealer to fit new signed, only use equipment approved tyres and to find out about available ac- by the approved network.
  • Page 119: Driver Correction Devices/Aids

    DRIveR CoRReCtIoN DevICeS aND aIDS (1/4) abS (anti-lock braking operating faults: Depending on the vehicle, this is com- posed of: system) © – the (anti-lock braking – lit up on the in- Under heavy braking, the ABS prevents system); strument panel along with the mes- the wheels from locking, allowing the –...
  • Page 120: Electronic Stability Program

    DRIveR CoRReCtIoN DevICeS aND aIDS (2/4) electronic stability program Understeer control operating faults eSP with understeer control This system optimises the action of the When the system detects an operating and traction control aSR ESP in the case of pronounced unders- fault the message “Check ESP”...
  • Page 121: Emergency Brake Assist

    DRIveR CoRReCtIoN DevICeS aND aIDS (3/4) hazard warning lights switching on The traction control ASR offers addi- tional safety, it is recommended that Depending on the vehicle, these may you do not drive with the function disa- light up in the event of sudden decel- bled.
  • Page 122 DRIveR CoRReCtIoN DevICeS aND aIDS (4/4) hill start assistance This device assists the driver when starting on hills (ascending or descend- ing). It prevents the vehicle from rolling The hill start assistance backwards by automatically applying system cannot completely the brakes when the driver lifts his/her prevent the vehicle from foot off the brake pedal to depress the rolling backwards in all sit-...
  • Page 123: Lane Departure Warning System

    LaNe DePaRtURe waRNING SySteM (1/2) This lane departure warning system no- tifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road.
  • Page 124 LaNe DePaRtURe waRNING SySteM (2/2) adjustment When a line is crossed and the indica- tors have not been activated, the func- From the vehicle settings customisation tion alerts the driver through warning  menu (please refer to the information on the “Vehicle settings customisation light on the instrument panel, menu”...
  • Page 125 CRUISe CoNtRoL/SPeeD LIMIteR: speed limiter function (1/3) The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. Controls Switching on Press switch 5 on the side showing 1 Limit speed activation, storage and ...
  • Page 126: Speed Limiter

    CRUISe CoNtRoL/SPeeD LIMIteR: speed limiter function (2/3) Driving exceeding the limit speed When a limited speed has been stored It is possible to exceed the limit speed and this speed is not reached, driving is at any moment. To do this: press the similar to driving a vehicle without the accelerator pedal firmly and fully speed limiter function.
  • Page 127 CRUISe CoNtRoL/SPeeD LIMIteR: speed limiter function (3/3) Switching off the function The speed limiter function is deacti- vated if you press switch 5: in this case a speed is no longer stored. The orange  indicator light on instrument panel A goes out to confirm that the function is deactivated.
  • Page 128 CRUISe CoNtRoL/SPeeD LIMIteR: cruise control function (1/4) The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). This function is an addi- tional driving aid.
  • Page 129: Cruise Control

    CRUISe CoNtRoL/SPeeD LIMIteR: cruise control function (2/4) Driving Once a cruising speed is stored and the cruise control function is active, you may lift your foot off the accelera- tor pedal. Switching on activating cruise control  At a steady speed (above 20 mph Press switch 5 on the side showing (30 km/h) approximately)
  • Page 130 CRUISe CoNtRoL/SPeeD LIMIteR: cruise control function (3/4) exceeding the cruising speed Putting the function on standby The cruising speed may be exceeded at any time by depressing the accelera- The function is suspended when you: tor pedal. – press switch 3 (O); The cruising speed flashes on the in- –...
  • Page 131 CRUISe CoNtRoL/SPeeD LIMIteR: cruise control function (4/4) Switching off the function The cruise control function is deacti- vated if you press switch 5: in this case a speed is no longer stored. The green  indicator light on the instrument panel A goes out to confirm that the function is deactivated.
  • Page 132: Operating Principle

    PaRkING DIStaNCe CoNtRoL (1/4) operating principle Ultrasonic detectors, installed in the front or rear bumper depending on the vehicle, measure the distance between the vehicle and an obstacle whilst re- versing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centi-...
  • Page 133: Parking Distance Control

    PaRkING DIStaNCe CoNtRoL (2/4) front parking distance control (depending on vehicle) operation The parking distance control system is only activated when the vehicle is driven at a speed below approximately 6 mph (10 km/h). Most objects located less than approx- imately 60 centimetres away from the front of the vehicle are detected and a beep is emitted.
  • Page 134 PaRkING DIStaNCe CoNtRoL (3/4) Deactivating the system You may permanently activate or deac- tivate the front or rear parking distance control separately. From the vehicle settings customisa- tion menu (refer to the information on the “Vehicle settings customisation menu” in Section 1), select the line “Front parking sensor”...
  • Page 135: Special Features

    PaRkING DIStaNCe CoNtRoL (4/4) operating faults When the system detects an operating fault , a beep sounds for approximately 3 seconds each time reverse gear is se- lected and is accompanied by the mes- sage “Check parking sensor” shown on the instrument panel A.
  • Page 136: Reversing Camera

    ReveRSING CaMeRa fixed clearance gauge 2 This gauge remains fixed and indicates The fixed clearance gauge comprises the vehicle trajectory if the wheels are coloured markers A, B and C indicating in line with the vehicle. the distance behind the vehicle: This system is initially used with the aid –...
  • Page 137: Automatic Gearbox

    aUtoMatIC GeaRbox (1/3) Driving in automatic mode Select position D. In most traffic con- ditions, you will not have to touch the gear selector lever again: the gears will change automatically at the right time and at the most suitable engine speed because the automatic system takes into account the vehicle load and road contour and adjusts itself to the particu-...
  • Page 138: Parking The Vehicle

    aUtoMatIC GeaRbox (2/3) Driving in manual mode Special circumstances Parking the vehicle With the selector lever in position D, – If the road contours and bends When the vehicle is stopped, move the move the lever to the left. Shifting the do not allow you to stay in auto- lever to position P while keeping your lever repeatedly allows you to change...
  • Page 139 aUtoMatIC GeaRbox (3/3) operating faults – when driving, if the message “Check auto gearbox” appears on the instrument panel, this indicates there is a fault. Contact your approved Dealer as soon as possible. – when driving, if the message “Auto gearbox overheating”...
  • Page 140 2.44...
  • Page 141: Your Comfort

    Section 3: Your comfort Air vents............... Manual air conditioning .
  • Page 142 AIR VENTS: air outlets (1/2) 1 side air vent 2 side window demister outlet 3 windscreen demister outlets 7 rear air vents 4 centre air vents 8 passenger footwell heater outlets 5 side window demister outlet 9 automatic climate control/manual air 6 side air vent conditioning control panel.
  • Page 143: Front Seats

    AIR VENTS: air outlets (2/2) Front seats Rear seats To remove bad odours from your ve- hicles, only use the systems designed Move tab 3 to the right or left to direct Air flow for this purpose. Consult an approved the air flow.
  • Page 144: Air Vents

    MANuAl AIR coNDITIoNINg (1/2) Distribution of air in the passenger compartment There are five air distribution options. Turn control 4 to choose the distribution option. The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed be- tween all the air vents, the front side window demisting vents, the...
  • Page 145: Adjusting The Ventilation Speed

    MANuAl AIR coNDITIoNINg (2/2) Adjusting the ventilation speed Turn control 2 clockwise to increase the air flow in the passenger compartment. Passenger compartment ventilation is referred to as “blown air”. The ven- tilation fan determines the air flow. However, it is also affected by the ve- hicle speed.
  • Page 146: Automatic Climate Control

    AuToMATIc clIMATE coNTRol (1/5) Automatic mode The automatic climate control system guarantees comfort in the passen- ger compartment and good visibility (except in the event of extreme condi- tions), whilst optimising consumption. The system controls the ventilation speed, air distribution, air recircula- tion, and starting and stopping the air conditioning and air temperature.
  • Page 147 AuToMATIc clIMATE coNTRol (2/5) clear View function Press button 10: the integrated indica- tor light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated.
  • Page 148 AuToMATIc clIMATE coNTRol (3/5) The displayed temperature values show a comfort level. When starting the engine, increas- ing or decreasing the value dis- played will not allow the com- fort level to be reached any more quickly. The system will always op- timise the temperature increase or decrease (the ventilation system does not start instantly at maximum...
  • Page 149 AuToMATIc clIMATE coNTRol (4/5) The air flow is directed to the windscreen and the front side window demisting vents. × The air flow is distributed be- tween all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells.
  • Page 150 AuToMATIc clIMATE coNTRol (5/5) Recycling This function is managed automati- cally (operation is confirmed by warn- ing light 14 on display 13), but you can also activate it manually. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle;...
  • Page 151: Maintenance

    AIR coNDITIoNINg: information and advice on use Advice on use In some situations, (air conditioning operating faults off, air recirculation activated, venti- Fuel consumption lation speed at zero or low, etc.) you As a general rule, contact your ap- You will normally notice an increase may notice that condensation starts proved dealer in the event of an op- in fuel consumption (especially...
  • Page 152: Electric Windows/Electric Sunroof

    Never leave your vehicle with the Electric windows From the driver’s seat, use switch: RENAULT card inside and never 1 for the driver’s side; Press or pull the switch to raise or lower leave a child (or a pet) unsuper- 2 for the front passenger’s side;...
  • Page 153: Sun Blind

    A B c body’s fingers, etc.) it stops and then moves back several centimetres. Driver’s responsibility Never leave your vehicle with the RENAULT card inside and never leave a Sunroof Sun blind child (or a pet) unsupervised, even – open the sun blind;...
  • Page 154: Precautions During Use

    Technical Department; RENAulT card twice in quick suc- (the window will close gradually), hold cession, or on the driver's door in – do not open the sunroof immedi-...
  • Page 155: Manual Window Winders/Interior Lighting

    MANuAl wINDow wINDERS/INTERIoR lIghTINg (1/2) Manual window winders courtesy light Front door lights Turn handle 1. Tilt switch 3 to move it to the position On equipped vehicles, light 5 comes on for: when the door is opened. – permanent lighting; –...
  • Page 156 INTERIoR lIghTINg (2/2) glove box light 6 luggage compartment light 7 Light 6 comes on when the cover is Depending on the vehicle, light 7 opened. comes on when the luggage compart- ment is opened. 3.16...
  • Page 157: Vanity Mirror

    SuN BlIND/MIRRoRS Front sun visor Vanity mirror child minder mirror Lower the sun visor 1 over the wind- Slide cover 3. Pull on recess 4 to open it. screen or unclip it and lower it over the Depending on the vehicle, light 2 is au- side window.
  • Page 158: Sun Visor

    SuN VISoR lateral sun visor Rear side sun blind Rear sun blind on the tailgate Pull the sun blind upwards using tab 1 Pull the sun blind upwards using hook 3 Pull the sun blind upwards using tabs 6 until hook 2 engages in its housing until it engages in housing 4 (make sure until they engage in hook 5 (make sure (make sure that the hook is correctly...
  • Page 159 PASSENgER coMPARTMENT SToRAgE/FITTINgS (1/6) Door pockets 1 Dashboard storage Storage compartment under compartment 2 the instrument panel 3 It can hold a 1.5 litre bottle. Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus Ensure that no hard, heavy or pointed objects are placed in the “open”...
  • Page 160 PASSENgER coMPARTMENT SToRAgE/FITTINgS (2/6) Sunglasses holder 4 Sun blind storage 5 central storage compartment or control 6 This can be used for storing motorway tickets, cards, etc. Depending on the vehicle, central con- trol 6 may be replaced by a storage compartment.
  • Page 161: Centre Console Storage

    PASSENgER coMPARTMENT SToRAgE/FITTINgS (3/6) central elbow rest 8 centre console storage Armrest storage compartment C compartment D The central elbow rest slides to allow the length to be adjusted. Slide it Lift up the armrest 8. With the armrest in the retracted posi- (movement A).
  • Page 162 PASSENgER coMPARTMENT SToRAgE/FITTINgS (4/6) Passenger storage cup holder 11 compartment It can hold a can, a cup or the ashtray. Pull handle 10 to open it. The glove box can hold A4-size docu- ments, a large bottle of water, etc. The storage compartment is ventilated and refrigerated.
  • Page 163 PASSENgER coMPARTMENT SToRAgE/FITTINgS (5/6) Rear door storage Front seat storage clothes hooks 14 compartment 12 compartments 13 grab handle 15 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle.
  • Page 164 PASSENgER coMPARTMENT SToRAgE/FITTINgS (6/6) Retaining hook 16 Storage drawer 17 under Front and rear underfloor front and rear seats storage 18 This is used to hold bags while the ve- hicle is moving. These drawers can hold a road atlas, These compartments can hold road the vehicle documentation, etc.
  • Page 165: Accessories Socket

    AShTRAY/cIgAR lIghTER/AccESSoRIES SockET cigar lighter 1 Accessories sockets With the ignition on, push in cigar You may use cigar lighter recess 1 or lighter 1; it will spring back with a click one of the sockets 3 (depending on the when it is ready.
  • Page 166: Rear Headrests

    REAR hEADRESTS Position for use To adjust side supports A Lift the headrest to maximum height, Depending on the vehicle, sections A then lower it until it locks. can be adjusted independently to the desired position. To remove the headrest Storage position B Press the tab(s) 1, then remove the headrest.
  • Page 167: Adjusting The Rear Seats

    ADJuSTINg ThE REAR SEATS To fold down a seatback (table posi- tion) Lower headrest 3. Lift handle 4 or, depending on the vehi- cle, pull tab 1. An occasional table position can be created by folding the seatback all the way down onto the seat cushion.
  • Page 168 REAR SEAT FuNcTIoNS (1/2) Folding up a seat Returning a seat to its normal Note: it may be necessary to move the passenger and/or driver’s seats position Lower the headrest. forwards and to lower the seatback in Lower the seat until it locks in place at order to tilt the seat as far forwards as Seat with control 2 floor level (movement A).
  • Page 169 REAR SEAT FuNcTIoNS (2/2) When fitting side seats, make sure that the seat belt buckle is inside the vehicle. When driving with the seats folded down: ensure you check that the seats are moved fully forward before folding them down and place the load as close as possible to prevent the seats from falling back when ac- celerating or during sudden braking.
  • Page 170 REAR SEAT oPERATIoN: 7-seater version (1/2) Third row rear seats To unfold a seat When moving third row rear – From the luggage compartment, seats: Folding up a seat remove the luggage cover and store – check that no one is near –...
  • Page 171 REAR SEAT oPERATIoN: 7-seater version (2/2) Accessing the third row rear use restriction – pull the second row rear seat to put it into the table position; seats It is not permitted to drive with a second – lift the seatback. row rear seatback or seat folded down –...
  • Page 172 TAIlgATE To open opening the doors manually from the inside Press button 1 and lift the tailgate. Special note To close If it is impossible to unlock the tailgate, Lower the tailgate using the handles 2 it can be done manually from inside: inside the tailgate to help you.
  • Page 173: Rear Parcel Shelf: Normal Chassis Versions

    REAR PARcEl ShElF: normal chassis versions Rear parcel shelf To remove, unhook the two straps 1. Fold section A onto section B, then pull up and towards you. To refit it, proceed in reverse order to removal. Do not place any objects, especially heavy or hard objects, on the parcel shelf.
  • Page 174: Luggage Cover: Long Chassis Versions

    luggAgE coVER: long chassis versions To remove the flexible Removing the luggage cover luggage compartment cover section of the luggage cover storage Push the luggage cover to the right (movement A) and lift the left-hand side Using handle 1, pull it gently to release Housing 3 in the luggage compartment of the inertia reel (movement B).
  • Page 175: Luggage Compartment Storage Space And Fittings

    luggAgE coMPARTMENT SToRAgE SPAcE AND FITTINgS (1/2) Side storage compartments 1 Storage compartment under luggage compartment carpet Depending on the vehicle, this may be Depending on the vehicle, to access used to hold oil containers etc. this, lift the luggage compartment carpet.
  • Page 176 luggAgE coMPARTMENT SToRAgE SPAcE AND FITTINgS (2/2) Separating the luggage Anchorage points compartment Hooks 6 located on each corner of the (depending on the vehicle) luggage compartment, allow the load to be secured. The loading area can be separated. Lift divider 4. The elastic band 5 on the back is used to hold objects vertically.
  • Page 177 TRANSPoRTINg oBJEcTS IN ThE luggAgE coMPARTMENT/TowINg (towing equipment) Always place the objects to be trans- ported so that their largest side rests against the back of the rear bench seat, for normal loads (example A) or against Always position the heavi- the back of the front seats B when the est items directly on the rear bench seatbacks are folded down.
  • Page 178: Luggage Net

    luggAgE NET (1/2) Fitting the luggage net Depending on the vehicle, this may be – attach the two hooks 3 on the net used when transporting animals or lug- straps 4 to the anchoring points 5; behind the front seats gage to isolate them from the passen- –...
  • Page 179 luggAgE NET (2/2) Fitting the luggage net – attach net strap hook 8 to the lower Depending on the vehicle, remove the ring; anchoring rings 11 before installing a behind the rear seats luggage net. (behind the second row rear seats on –...
  • Page 180: Roof Bars

    RooF BARS Access to the mounting points Open the doors to access the mount- For information on the range of ing points 1. equipment adapted to your vehi- cle, we advise you to consult an ap- proved Dealer. Refer to the fitting instructions for in- formation on how to fit roof bars and conditions of use.
  • Page 181: Multimedia Equipment

    MulTIMEDIA EquIPMENT Multimedia systems hands-free telephone The equipment described below may integrated control or may not be fitted to the vehicle, and On equipped vehicles, use steering its location may vary, depending on the column control 5 and microphone 6. vehicle navigation system version.
  • Page 182 3.42...
  • Page 183 Section 4: Maintenance Bonnet ............... . Engine oil level/Engine oil change .
  • Page 184: Bonnet

    Bonnet Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight.
  • Page 185: Engine Oil Level/Engine Oil Change

    enGIne oIL LeVeL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- In order to prevent splashback, it is tween oil changes. recommended that a funnel be used However, contact your approved when topping up/filling with oil...
  • Page 186 enGIne oIL LeVeL: topping up, filling (1/3) topping up/Filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...
  • Page 187 enGIne oIL LeVeL: topping up, filling (2/3)
  • Page 188: Oil Change

    enGIne oIL LeVeL: topping up, filling oIL ChAnGe (3/3)/ oil change Consult your approved Dealer at Service interval: refer once if you notice an abnormal or Maintenance Service Booklet for your repeated drop in any of the fluid vehicle. levels. Average capacities for oil change including oil filter (for information)
  • Page 189: Levels

    LeVeLS (1/3) Checking intervals Replacement intervals Check the coolant level regularly Refer to the Maintenance Service (very severe damage is likely to be Booklet for your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
  • Page 190: Brake Fluid Level

    LeVeLS (2/3) Level 2 topping up It is normal for the level to drop as the After any operation on the hydraulic cir- brake shoes become worn, but it must cuit, a specialist must replace the fluid. never drop lower than the “MInI” warn- Only use fluids approved by our ing line.
  • Page 191: Windscreen/Headlight Washer Reservoir

    LeVeLS FILteRS (3/3) Filters Liquid Windscreen washer fluid. In winter, use The replacement of filter elements (air anti-freeze product. filter, passenger compartment filter, diesel filter, etc.) is scheduled in the Jets maintenance operations for your vehi- cle. Use a tool such as a needle to adjust the height of the windscreen washer Replacement intervals for filter el- jets.
  • Page 192: Tyre Pressure

    tyRe pReSSURe tyre safety and use of snow chains Refer to the information on “Tyres” in Section 5 for the servicing con- ditions and, depending on the ver- sion, the use of chains. Special note For vehicles used fully laden (maximum permissible all-up...
  • Page 193: Battery

    BAtteRy (1/2) Depending on the vehicle, a system continuously checks the battery charge status. If this drops, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. Then the message “Battery charging” appears on the in- strument panel for the duration of the charging time.
  • Page 194 BAtteRy (2/2) Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. After changing or disconnecting the battery, the message “New battery?” will appear on the instrument panel. Select “Yes” or “No” with a short press on one of the buttons 8 or 9, then con- firm with a long press on one of the two buttons.
  • Page 195: Bodywork Maintenance

    BoDyWoRk MAIntenAnCe (1/2) Minor impacts A well-maintained vehicle will last Allow rust to form following minor im- longer. It is therefore recommended to pacts. You should take a minimum number of maintain the exterior of the vehicle reg- precautions in order to safeguard your Use solvents not approved by our ularly.
  • Page 196 BoDyWoRk MAIntenAnCe (2/2) you should – bird droppings, which cause a If it is necessary to clean mechani- chemical reaction with the paint that cal components, hinges, etc., spray Observe the vehicle stopping distances rapidly discolours paintwork and them with products approved by our when driving on gravelled surfaces to may even cause the paint to peel Technical Department to protect them...
  • Page 197: Interior Trim Maintenance

    InteRIoR tRIM MAIntenAnCe (1/2) Glass instrument panel textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
  • Page 198 InteRIoR tRIM MAIntenAnCe (2/2) Removal/replacing removable you should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
  • Page 199: Practical Advice

    RENAULT card: battery ........
  • Page 200: Puncture

    PuncturE/EMErGEncY SPArE WHEEL (1/2) In case of puncture Special note The Tyre Pressure Monitor function Depending on the vehicle, a tyre infla- does not check the emergency spare tion kit or emergency spare wheel is wheel (the wheel replaced by the emer- provided (refer to the following pages).
  • Page 201 PuncturE/EMErGEncY SPArE WHEEL (2/2) As the punctured wheel is wider than the emer- gency spare wheel, when Emergency spare wheel B to refit emergency spare wheel B you place the punctured Stand the wheel up with the valve to- It is located under the vehicle. In the wheel in the emergency spare wards you.
  • Page 202 tYrE PrESSurE KIt (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
  • Page 203 tYrE PrESSurE KIt (2/3) – press switch 5 to inflate the tyre to the recommended pressure (check the label affixed to the edge of the driver’s door); – after a maximum of 5 minutes, stop inflating and read the pressure (on pressure gauge 4);...
  • Page 204 tYrE PrESSurE KIt (3/3) Precautions when using the – affix the driving recommendation label 9 to the dashboard where it can easily be seen by the driver; The kit should not be operated for more – store the kit; than 15 consecutive minutes. –...
  • Page 205: Towing Hitch

    tOOLS (1/2) Hubcap tool 4 This tool is used to remove the wheel trims. Bolt guide 5 For tightening/loosening wheel bolts on vehicles fitted with alloy wheels towing hitch 6 Refer to the information on “Towing” in Section 5. Do not leave the tools un- secured inside the vehicle as they may come loose under braking.
  • Page 206 tOOLS /WHEEL trIM (2/2) 7-seater version 5-seater version Wheel trim The tools are in compartment 8 of the Lift luggage compartment carpet 9, and Remove it using hubcap tool 4 by en- luggage compartment: lift the third row secure it with the hook. gaging the hook in the recess provided rear right-hand seat, pull tab 7 then next to valve 12 (to attach the metal...
  • Page 207 cHAnGInG A WHEEL (1/2) Vehicles equipped with a jack Offer up the jack 1 horizontally; the jack head must be lined up with the and wheelbrace sill, closest to the wheel concerned, as If necessary, remove the wheel trim. shown by arrow 2. Use the wheelbrace 3 to slacken off the Start cranking the jack up by hand to wheel bolts.
  • Page 208 cHAnGInG A WHEEL (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel onto the hub and rotate it until the mounting holes in the wheel coincide with those of the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel.
  • Page 209 tYrES (1/3) tyre and wheel safety When the tread has worn down to the wear warning strips, these strips will The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.
  • Page 210: Tyre Pressures

    tYrES (2/3) tyre pressures Fitting new tyres Pressures should be checked when the tyres are cold; ignore higher pressures Adhere to the tyre pressures (including which may be reached in hot weather the emergency spare wheel). The tyre or following a fast journey. pressures should be checked at least If tyre pressures cannot be checked once a month and additionally before...
  • Page 211: Changing A Wheel

    tYrES (3/3) use in winter Studded tyres This type of equipment may only be chains used for a limited period and as laid For safety reasons, fitting snow down by local legislation. It is neces- chains to the rear axle is strictly for- sary to observe the speed specified by bidden.
  • Page 212: Headlights (Changing Bulbs)

    FrOnt HEADLIGHtS: changing bulbs (1/3) Daytime running light (depending on the vehicle) Remove cover B, turn bulb holder 3 to release it then replace the bulb. Daytime running light bulb type: P21LL. Discharge bulb main beam headlights/dipped beam headlights Never open cover A Bulb type: D1S.
  • Page 213: Halogen Headlights

    FrOnt HEADLIGHtS: changing bulbs (2/3) Main beamA/dipped B refitting halogen headlights Carry out the operations in reverse order. Ensure that the bulb is correctly removal repositioned (pay attention to the direc- tion of fitting). Remove the cover A or B, unclip the bulb raising the connector 4 or 5 (move- It is essential to use anti-U.V.
  • Page 214: Front Headlights: Changing Bulbs

    FrOnt HEADLIGHtS: changing bulbs (3/3) Front fog lights 9 The front bumper needs to be removed; consult an approved Dealer. Daytime running lights 10 Any operation on (or modi- Please see an authorised dealer. fication to) the electrical system must be performed by an approved dealer since an incorrect connection might damage the electrical equipment...
  • Page 215: Rear Lights (Changing Bulbs)

    rEAr LIGHtS AnD InDIcAtOr LIGHtS: changing bulbs (1/4) LED lighting Long chassis version From the outside, undo screw 2 using a flat-blade screwdriver or similar and The lights are equipped with an LED pull the light unit towards you. Direction indicator lights/brake and lighting system as soon as the side side lights Unclip the bulb holder a quarter of a...
  • Page 216 rEAr LIGHtS AnD InDIcAtOr LIGHtS: changing bulbs (2/4) normal chassis version Unclip the bulb holder by pressing on refitting the tabs 6. To refit, proceed in the reverse order, Direction indicator lights and brake Replace the bulb. taking care not to damage the wiring. lights note: do not remove seal 9.
  • Page 217 rEAr LIGHtS AnD InDIcAtOr LIGHtS: changing bulbs (3/4) rear fog light and reversing Side light From the outside of the vehicle, pull on the light unit to remove it then unscrew light From the luggage compartment, unclip bulb holder 11 a quarter of a turn. (depending on the vehicle) the cover.
  • Page 218: Indicator Lights (Changing Bulbs)

    rEAr LIGHtS AnD SIDE LIGHtS: changing bulbs (4/4) High level brake light 13 number plate lights 14 Indicator lights 16 Consult an approved Dealer. Unclip light 14 by pressing tab 15. Unclip indicator light 16 using a flat- blade screwdriver or similar. Position Remove the light cover to gain access it to A to tilt the rear indicator light to- to the bulb.
  • Page 219: Interior Lights (Changing Bulbs)

    IntErIOr LIGHtInG: changing bulbs (1/2) courtesy light Door lights Sliding central console light – Set the three switches to the central Unclip light 2 (using a flat-blade screw- Unclip bulb 3 from its support. position; driver or similar). Bulb type: W5W. –...
  • Page 220: Interior Lighting: Changing Bulbs

    IntErIOr LIGHtInG: changing bulbs (2/2) Luggage compartment lights Disconnect the light. Press tab 5 to release lens 7 and Unclip lights 4 using a flat-blade screw- access bulb 6. driver or similar. Bulb type: W5W. The bulbs are under pres- sure and can break when replaced.
  • Page 221: Fuses

    FuSES (1/2) Fuse box tweezers 1 If any electrical component does not Remove the fuse using tweezers 1, lo- work, check the condition of the fuses. cated at the back of flap A or B. Unclip cover A or B (depending on ve- To remove the fuse from the tweezers, Check the fuse in question hicle).
  • Page 222 FuSES (2/2) Allocation of fuses 8 Interior rear-view mirror; Some accessories are protected by fuses located in the engine compart- (the presence of certain fuses depends 9 Rear screen wiper; ment in fuse box C. on the vehicle equipment level) 10 and 11 Rear electric windows;...
  • Page 223: Connecting A Battery Charger

    BAttErY: troubleshooting (1/2) to avoid all risk of sparks: connecting a battery charger – Ensure that any consumers (cour- the battery charger must be com- tesy lights, etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.
  • Page 224 BAttErY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
  • Page 225: Replacing The Battery

    (insert the the next time the vehicle is started, the place the RENAULTcard battery, press RENAULT card in the card reader) and message will disappear. button 1, pulling on emergency key 2, lock/unlock the vehicle (refer to the in- note: it is not advisable to touch the then unclip cover 3 using tab 4.
  • Page 226 FIttInG A rADIO If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: – the radio 1; – tweeter speakers 2; – bass speakers 3. To install any equipment, please con- –...
  • Page 227: Accessories

    AccESSOrIES Before fitting an electrical or If you are using an anti-theft electronic device (particu- device, only attach it to the larly for transmitters/receiv- brake pedal. ers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle.
  • Page 228: Windscreen Wiper Blades

    WIPEr BLADES: replacing Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...
  • Page 229 If your vehicle is the towing or r for vehicles with automatic gear- vehicle, do not exceed the maximum boxes), insert the RENAULT card in the towing weight for your vehicle (refer card reader, then press the engine start to the information on “Weights”...
  • Page 230: Towing: Breakdown

    5 (never use the driveshafts). Unclip cover 6 or 7 by sliding a flat tool These towing points may only be used (or the key integrated in the RENAULT for towing: never use them for lifting the card) under the cover.
  • Page 231 Dealer as soon as possible. using the rEnAuLt card POSSIBLE cAuSES WHAt tO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle (refer to the information on “Locking/unlocking the...
  • Page 232: Operating Faults

    Starting conditions are not Refer to the information on “Starting/stopping the fulfilled. engine” in Section 2. The RENAULT “hands-free” Insert the card in the card reader in order to start card does not work. the engine. Refer to the information on “Starting/stopping the engine”...
  • Page 233 OPErAtInG FAuLtS (3/5) On the road POSSIBLE cAuSES WHAt tO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the sures, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer.
  • Page 234 OPErAtInG FAuLtS (4/5) On the road POSSIBLE cAuSES WHAt tO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and ant temperature indicator is in the contact an approved dealer.
  • Page 235 OPErAtInG FAuLtS (5/5) Electrical equipment POSSIBLE cAuSES WHAt tO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”.
  • Page 236 5.38...
  • Page 237: Technical Specifications

    Section 6: Technical specifications Vehicle identification plates ............Engine identification plates .
  • Page 238: Vehicle Identification Plates

    Vehicle identification plates the information shown on the ve- 6 Technical specifications of vehicle. hicle identification plate should be 7 Vehicle paint reference. quoted on all correspondence or 8 Equipment level. orders. 9 Vehicle type. 10 Trim code. Vehicle identification plate A 11 Additional equipment specifica- 1 Vehicle type and chassis number.
  • Page 239: Engine Identification Plates

    engine identification plates (1/2) the information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
  • Page 240 engine identification plates (2/2) the information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
  • Page 241: Dimensions

    dimensions (in metres) (1/2) normal chassis versions 0,888 2,702 0,753 1,546 4,343 1,624* 1,547 2,077 Unladen...
  • Page 242 dimensions (in metres) (2/2) long chassis versions 0,888 2,769 0,903 1,536 4,560 1,675* 1,539 2,077 Unladen...
  • Page 243: Engine Specifications

    engine specifications Versions 1.6 16V 1.4 tce 2.0 16V 1.5 dci 1.6 dci 1.9 dci 2.0 dci engine type (see engine plate) cubic capacity (cc) 1.598 1.395 1.995 1.461 1 598 1.870 1.995 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.
  • Page 244: Weights

    Weights (in kg) the weights indicated are for a basic vehicle without options: they may vary depending on your vehicle’s equipment. consult an approved dealer. maximum permissible all-Up Weight (mmac) Weights are indicated on the vehicle identification plate (refer gross train Weight (mtR) to the information on “Vehicle identification plates”...
  • Page 245: Replacement Parts And Repairs

    Replacement paRts and RepaiRs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
  • Page 246: Service Sheets

    seRVice sheets (1/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 247 seRVice sheets (2/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 248 seRVice sheets (3/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 249 seRVice sheets (4/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 250 seRVice sheets (5/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 251 seRVice sheets (6/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 252: Anticorrosion Check

    anticoRRosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.16...
  • Page 253 anticoRRosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.17...
  • Page 254 anticoRRosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.18...
  • Page 255 anticoRRosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.19...
  • Page 256 anticoRRosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.20...
  • Page 257 anticoRRosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.21...
  • Page 258 6.22...
  • Page 259: Alphabetical Index

    AlphAbeticAl index (1/5) ABS ...............2.23 → 2.26 catalytic converter............. 2.9 – 2.10 accessories................ 5.29 central door locking ........1.8, 1.12 → 1.14 accessories socket ............3.25 changing a bulb .............5.14 → 5.20 additional methods of restraint .....1.24 → 1.27, 1.30 changing a wheel............5.9 – 5.10 side protection ............. 1.29 changing gear ..........2.11, 2.41 → 2.43 to the rear seat belts ........1.24 → 1.28 child restraint/seat ......1.31 – 1.32, 1.34 → 1.46 adjusting your driving position ...........
  • Page 260: Headlight Beam Adjustment

    AlphAbeticAl index (2/5) driving ..2.2 → 2.5, 2.9 → 2.17, 2.19 → 2.26, 2.29 → 2.39,  front seat adjustment ..........1.16 – 1.17 2.41 → 2.43 front seats driving position adjustment ............1.16 – 1.17 settings ................ 1.20 with electric controls ............ 1.18 with manual controls ............ 1.16 fuel electric beam height adjustment ........1.83 advice on fuel economy ..........
  • Page 261 AlphAbeticAl index (3/5) sounding the horn ............1.77 brake lights ..............5.17 hubcap tool ..............5.7 – 5.8 dipped beam headlights ......1.78, 5.14 → 5.16 direction indicators ....1.77, 5.14 → 5.17, 5.19 – 5.20 fog lights ............. 1.81, 5.17 indicators ............1.77, 5.14 → 5.16 hazard warning ............1.77 indicators: main beam headlights ......1.80, 5.14 → 5.16 direction indicators ..........1.77, 5.17 number plate lights ............
  • Page 262 .......3.19 → 3.24, 3.35 – 3.36 functions ..............3.27 sun blinds ............... 3.17 – 3.18 rear view mirrors ..............1.76 sun visor ................3.17 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.14 sunroof..............3.12 → 3.14 RENAULT card switching on the vehicle ignition .......... 2.4 battery ................5.27 use ...............1.2 → 1.9 RENAULT card battery ............
  • Page 263 AlphAbeticAl index (5/5) transporting children ......1.31 – 1.32, 1.34 → 1.46 transporting objects in the luggage compartment ........3.37 luggage net ............3.38 – 3.39 trims ..................5.8 trip computer and warning system... 1.54 → 1.58, 1.63 → 1.71 tyre inflation kit............5.4 → 5.6 tyre pressure........2.19 → 2.22, 4.10, 5.12 tyre pressure monitor..........2.19 → 2.22 tyre pressures ..............4.10 tyres ........2.19 → 2.22, 4.10, 5.11 → 5.13 unlocking the doors ..........
  • Page 265 à999106540Rê ñ ò ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Table of Contents