Hide thumbs Also See for 2013 Clio:
Table of Contents

Advertisement

CLIO
DRIVER'S HANDBOOK

Advertisement

Table of Contents
loading

Summary of Contents for Renault 2013 Clio

  • Page 1 CLIO DRIVER’S HANDBOOK...
  • Page 2 Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please ELF has developed a complete range of lubricants for RENAULT: refer to your maintenance document. engine oils manual and automatic gearbox oils Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
  • Page 3: Driving

    This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.
  • Page 5: Table Of Contents

    Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
  • Page 7 RENAULT card: general information, use, deadlocking ........
  • Page 8 KEY/RADIO FREQUENCY REMOTE CONTROL: general information (1/2) Key A Radio frequency remote 4 Locking/unlocking the tailgate only (for remote control units with three control unit B or C 1 Coded key for ignition switch, doors buttons). and fuel filler cap. 2 Locking the doors and tailgate.
  • Page 9: Doors

    KEY/RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the environ- ment. It is therefore important when handling the remote control to ensure Replacement and additional keys that you do not lock or unlock the ve- or remote controls.
  • Page 10: Unlocking The Doors

    RADIO FREQUENCY REMOTE CONTROL: use (1/2) Unlocking the doors Driver’s responsibility Remote control A or B Press unlocking button 2. Never leave your vehi- The hazard warning lights and indicator cle with the key inside and lights flash once to indicate unlocking. never leave a child (or a Special notes (for some countries): pet) unsupervised, even for a short...
  • Page 11: Luggage Compartment Lid

    RADIO FREQUENCY REMOTE CONTROL: use (2/2) Unlocking/locking the luggage compartment lid only (for some countries) Press button 5 to unlock or lock the tail- gate. The hazard warning lights and indica- tor lights flash once to indicate that the tailgate is unlocked if the vehicle doors are locked.
  • Page 12 RADIO FREQUENCY REMOTE CONTROL: deadlocking To activate deadlocking If fitted to the vehicle, this allows the doors to be locked and prevents them Press button 1 twice in quick succes- from being opened with the interior sion. handles (for example, by breaking the window and then trying to open the The hazard warning lights and indica- doors from the inside).
  • Page 13: Battery Life

    (see the following pages); humid areas. – starting the engine; refer to the in- Do not keep the RENAULT card in a formation on “Starting the engine” in place where it could be bent or dam- aged accidentally, such as in a back Section 2.
  • Page 14 Dealer. If a RENAULT card is replaced, it will be necessary to take the vehi- cle and all of its RENAULT cards to an approved Dealer to initialise the system. You may use up to four RENAULT...
  • Page 15: Locking The Doors

    If a door or the tailgate is open or not tailgate is unlocked if the vehicle doors properly closed, or if a RENAULT card are locked. is still in the reader, the doors and tail-...
  • Page 16 On equipped vehicles, in addition to the functions of the remote control Walk up to your vehicle carrying your RENAULT card, it can be used to lock RENAULT card. and unlock without using the RENAULT As soon as you put your hand through a card, when it is in access zone 1.
  • Page 17: Locking The Vehicle

    Driver’s responsibility Never leave your vehicle with the RENAULT card inside and never leave Note: the RENAULT card must be a child (or a pet) unsupervised, even for a short while.
  • Page 18 – press button 2 twice in quick succes- Unlock the vehicle using button 1 on sion; the RENAULT card. The hazard warn- ing lights flash once to indicate that the – or press on the button on one of the doors have been unlocked.
  • Page 19 A beep will let you know if you have left With the doors unlocked or the “hands- the card in the reader when you open free” RENAULT card in your posses- the driver’s door, and the ‘Remove sion, hold handle 1 and pull it towards card’...
  • Page 20: Child Safety

    OPENING AND CLOSING THE DOORS (2/2) Safety of rear occupants The driver can authorise operation of the rear doors and, depending on the ve- hicle, the electric windows by press- ing switch 3; the integrated indicator light goes out. Depending on the vehicle, in the event of a fault: –...
  • Page 21 LOCKING/UNLOCKING THE DOORS (1/3) Locking/unlocking from the outside This is done using the RENAULT remote control unit: refer to the information on “Radio frequency remote control: gen- eral information” and “RENAULT card: general information”. In some cases, the key/radio frequency...
  • Page 22 Use of emergency key 4 integrated Insert key 4 into the lock of the front Manual locking of each of the doors in the RENAULT card left-hand door and lock or unlock. With the door open, turn screw 6 using Insert the end of emergency key 4 into key 4 and close the door again.
  • Page 23 RENAULT card fails: with the vehicle in the event of an emer- ignition off, press switch 7 for more gency.
  • Page 24: Operating Principle

    RENAULT ANTI-INTRUDER DEVICE (RAID) Operating principle Operating faults After the vehicle is started, the system If you find an operating fault (no auto- automatically locks the doors once your matic locking, the indicator light incor- speed reaches approximately 5 mph porated in button 1 does not light up (7 km/h).
  • Page 25: Engine Immobiliser System

    The vehicle is automatically protected liser system. a few seconds after the engine is switched off. If there is interference and/or the hands- free RENAULT card is not recognised, move the card or insert it fully into the card reader. Vehicle protection tell-tale light...
  • Page 26 FRONT HEADRESTS (1/2) Fixed, non-adjustable Height adjustable headrest B headrest A It can be identified by the presence of button 2. To raise the headrest To raise the headrest Press button 1 and lift the headrest to release it. Pull the headrest upwards to the de- sired height.
  • Page 27 FRONT HEADRESTS (2/2) To refit the headrest If the rod setting has been altered, pull rods 3 out fully (check that they are properly aligned and clean). If you are having difficulty, check that the notches are facing the front. Insert the headrest rods into the holes (tilt the seatback backwards if neces- sary).
  • Page 28: Heated Seats

    FRONT SEATS (1/2) To move forwards or To raise or lower the seat To tilt the seatback backwards base Turn control knob 5 and tilt the seat- back to the desired position. Lift handle 1 underneath the seat to Move lever 2 as many times as neces- release.
  • Page 29 FRONT SEATS (2/2) When a person, an object or a child seat prevents the front seats from lock- ing, perform the following operations: – ask all of the passengers to leave the vehicle and remove any bulky objects from the rear seats; –...
  • Page 30: Steering Wheel/Power-Assisted Steering

    STEERING WHEEL/POWER-ASSISTED STEERING Power Assisted Steering Never drive with an inadequately charged battery. Variable power assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) whilst the force needed to steer increases...
  • Page 31: Seat Belts

    SEAT BELTS (1/4) Before starting, first adjust your driv- Always wear your seat belt when trav- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
  • Page 32 SEAT BELTS (2/4) ß Driver’s seat belt reminder warning light If the driver’s seat belt is not fastened the light remains lit when the vehicle is started, then when the car reaches a speed of approximately 6 mph (10 km/h), it flashes and a beep sounds for about 90 seconds.
  • Page 33 SEAT BELTS (3/4) Rear side seat belts 7 Rear centre seat belt Fasten sliding buckle 10 into the corre- sponding red catch 12. The belts are locked, unlocked and Unwind belt 9 slowly from its housing, adjusted in the same way as the front then fasten buckle 8 into the corre- belts.
  • Page 34 SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats) contact an authorised dealer. –...
  • Page 35 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretension- an accident. ers; – No operation whatso- –...
  • Page 36: Methods Of Restraint In Addition To The Front Seat Belts

    METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Chest-level and lap belt load Air bag for driver and front limiters passenger Above a certain severity of impact, this Fitted to the driver and passenger side. mechanism is used to limit the force of The presence of this equipment is in- the belt against the body so that it is at dicated by the word “Air bag”...
  • Page 37 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operation Operating faults å This system is only operational when Warning light 4 will light up on the ignition is switched on. the instrument panel when the ignition In a severe frontal impact, the air bags is turned on and then go out after a few inflate rapidly, cushioning the impact seconds.
  • Page 38 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. Warnings concerning the driver’s air bag –...
  • Page 39 METHODS OF RESTRAINT IN ADDITION TO THE REAR SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
  • Page 40 SIDE PROTECTION DEVICES Side Airbags This airbag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Curtain Airbags This airbag may be fitted along the top of each side of the vehicle and is trig- gered along the front and rear side win-...
  • Page 41: Additional Methods Of Restraint

    ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. The airbag is designed to complement the action of the seat belt.
  • Page 42: Child Safety: General Information

    CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- Driver’s responsibility ished growing.
  • Page 43 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
  • Page 44 CHILD SAFETY: Choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
  • Page 45 CHILD SAFETY: choosing a child/baby seat mounting (1/2) Attachment using the ISOFIX There are two ways of attaching child Do not use the child seat seats: via the seat belt or using the system if it may unfasten the seat ISOFIX system.
  • Page 46 CHILD SAFETY: choosing a child/baby seat mounting (2/2) The two rings 1 are located between The third ring is used to attach the – depending on the vehicle, unclip the seatback and the seat base of the upper strap on some child seats: mobile floor cover 6 then pass seat and are identified by a marking.
  • Page 47: Fitting A Child Seat

    CHILD SAFETY: Fitting a child seat In the front seat In the rear side seat Some seats are not suitable for fitting child seats. The diagram on the follow- The laws concerning children travel- A carrycot can be installed across the ing page shows you how to attach a ling in the front passenger seat differ in vehicle and will take up at least two...
  • Page 48 CHILD SAFETY: installation diagram (3 and 5 door version) Child seat fitted using the ISOFIX mounting ü seat which allows an ISOFIX child seat to be fitted. Note: Only three-door vehicles are fitted with the 2-point ISOFIX system on the front passenger seat. ±...
  • Page 49 CHILD SAFETY: installation diagram (sport tourer version) Child seat fitted using the ISOFIX mounting ü seat which allows an ISOFIX child seat to be fitted. ± the rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.
  • Page 50 CHILD SAFETY: installation table (3- and 5-door versions) ( 1/2) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Weight of Front passenger Rear side Type of child seat Seat size ISOFIX Rear centre seat...
  • Page 51 CHILD SAFETY: installation table (3- and 5-door versions) ( 2/2) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UD = Seat which only allows a rear-facing standardised “Universal”...
  • Page 52 CHILD SAFETY: installation table (sport tourer versions) ( 1/2) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Weight of Front passenger Type of child seat Seat size ISOFIX Rear side seats (6) Rear centre seat...
  • Page 53 CHILD SAFETY: installation table (sport tourer versions) ( 2/2) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UD = Seat which only allows a rear-facing standardised “Universal”...
  • Page 54: Deactivating, Activating The Front Passenger Airbag

    CHILD SAFETY: deactivating/activating the front passenger air bag (1/3) Deactivating the front To deactivate the airbags: with the vehicle stopped and the ignition off, passenger airbags push and turn lock 1 to the OFF posi- (on equipped vehicles) tion. You must deactivate the devices in ad- With the ignition on, you must check dition to the front passenger seat belt before fitting a child seat in the front...
  • Page 55 CHILD SAFETY: deactivating/activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER...
  • Page 56 CHILD SAFETY: deactivating/activating the front passenger air bag (3/3) DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag.
  • Page 57: Audible And Visual Signals

    AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0.
  • Page 58: Driving Position

    DRIVING POSITION: LEFT-HAND DRIVE (1/2) 6 7 8 9 1.52...
  • Page 59: Instrument Panel

    28 Controls for: system information readout. 16 Central door locking switch. – traction control and ESP; 7 Ignition switch (vehicle with key). 17 RENAULT card reader (vehicle – headlight beam height remote with RENAULT card). adjustment; – instrument panel lighting rheo- 8 Centre air vents.
  • Page 60 DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 9 10 11 12 13 1.54...
  • Page 61 – exterior lights; – front and rear fog lights. 17 Fuse box. 9 Instrument panel. 18 Central door locking switch. 10 Driver’s Airbag location, horn, 19 RENAULT card reader (vehicle cruise control/speed limiter con- with RENAULT card). trols. 20 Gear lever. 1.55...
  • Page 62: Warning Lights

    WARNING LIGHTS (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. å Left-hand direction indicator Air bag warning light tell-tale This lights up when the ignition is switched on and goes out after a few Right-hand direction indica- seconds.
  • Page 63 WARNING LIGHTS (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Ô Anti-lock braking warning Coolant temperature warn- light ing light This lights up when the ignition is This lights up when the ignition is switched on and goes out after a few switched on and goes out after a few seconds.
  • Page 64 WARNING LIGHTS (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Ú Battery charge warning light Handbrake on and brake cir- cuit incident warning light This lights up when the ignition is switched on and goes out after a few This comes on when the ignition is seconds.
  • Page 65 WARNING LIGHTS (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Ò É Electronic fault warning light Preheating warning light (diesel version) This lights up when the ignition is switched on and goes out after a few This should come on when the igni- seconds.
  • Page 66 INSTRUMENT PANEL: displays and indicators (1/3) Rev counter 1 (graduations x 1000) Coolant temperature indicator 2 In normal use, the needle should be below zone A. Under harsh operating conditions the needle may approach this zone. Ö This is not serious unless the ®...
  • Page 67: Trip Computer And Warning System

    INSTRUMENT PANEL: displays and indicators (2/3) Speedometer 5 (km or miles per hour) Overspeed buzzer Depending on the vehicle, a buzzer sounds for approximately 10 seconds every 40 seconds, as long as the ve- hicle is travelling in excess of 72 mph (120 km/h).
  • Page 68 INSTRUMENT PANEL: displays and indicators (3/3) Multifunction display This indicates: – that a door or the tailgate is open or not properly closed, – the gear engaged (for vehicles fitted with an automatic or Quickshift gear- box). Door indicator light or multifunction display 7 (depending on vehicle) Opening elements warning...
  • Page 69: On-Board Computer

    ON-BOARD COMPUTER: general information (1/3) Trip computer and warning system This displays the following information on instrument panel display A or B (po- sition varies according to vehicle): – information messages (distance travelled, journey parameters etc.); – Operating fault messages (gener- ©...
  • Page 70 ON-BOARD COMPUTER: general information (2/3) c) mileage before service, d) programmed speed (speed limiter/ cruise control), e) on-board log: operating fault and in- formation message readout. Display selection keys 1 and 2 Scroll through the following informa- tion in this order or reverse the order by briefly pressing the key repeatedly.
  • Page 71 ON-BOARD COMPUTER: general information (3/3) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption, range and average speed will become more stable and reliable the further you travel after pressing the...
  • Page 72 ON-BOARD COMPUTER: trip settings (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by pressing button 2 Interpreting the display selected Display A Display B 3382.3 103288 KM a) Total mileage recorder 185.5 KM (visible on the first line of the display B) 332.3...
  • Page 73 ON-BOARD COMPUTER: trip settings (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by pressing button 2 Interpreting the display selected Display A Display B CURRENT Current fuel consumption L/100 This value is displayed after a speed of approximately 20 mph 5.8 L/100 (30 km/h) is reached.
  • Page 74 ON-BOARD COMPUTER: trip settings (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections Interpreting the display selected by pressing button 2 c) Distance before service Display A Display B Distance remaining until the next service. There are several scenarios: 12000 SERVICE DUE IN...
  • Page 75 ON-BOARD COMPUTER: trip settings (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by pressing button 2 Interpreting the display selected Display A Display B SPEED LIMITER 70 KM/H d) Cruise control/speed limiter programmed speed (depend- ing on vehicle) Refer to the information on the “Cruise control - Speed limiter”...
  • Page 76 TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpretation of messages “BOOT OPEN”...
  • Page 77 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. ©...
  • Page 78 TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages.
  • Page 79: Clock And Exterior Temperature

    CLOCK AND EXTERIOR TEMPERATURE (1/2) 3382.3 TIME 16:20 16:30 Display A Then press and hold button 3 to con- firm the time set. The time is displayed when the ignition The minutes flash; repeatedly press or is switched on. press and hold button 2 to set them. To access display 1 for setting the time, When setting is complete, the hours press button 2 or 3.
  • Page 80 CLOCK AND EXTERIOR TEMPERATURE (2/2) Vehicles fitted with navigation aid External temperature systems, telephones, etc. indicator Refer to the separate instructions for Special note: the function to understand the special features of this equipment. When the exterior temperature is - 3°C to + 3°C, the °C characters flash (sig- nalling a risk of ice on the road).
  • Page 81: Rear-View Mirrors

    REAR VIEW MIRRORS (1/2) Heated door mirrors With the engine running, mirror de- icing is activated simultaneously with rear screen de-icing/demisting. For safety reasons, carry out any adjustments when the vehicle is not being driven. Door mirrors with manual Door mirrors with electrical adjustment adjustment To adjust the mirror, move lever 1.
  • Page 82: Interior Rear View Mirror

    REAR VIEW MIRRORS (2/2) Folding door mirrors Interior rear view mirror Move button 2 to position F and the Its position can be adjusted. When driv- door mirrors fold in. To reset them for ing at night, to avoid being dazzled by driving, return to position C, D or E.
  • Page 83: Exterior Lighting And Signals

    EXTERIOR LIGHTING AND SIGNALS (1/5) Side lights Adjusting the brightness of the instrument panel lighting Turn the end of stalk 1 until the symbol is opposite mark 2. Turn control 3 downwards to reduce the brightness and upwards to increase it. An indicator light on the instrument panel will come on.
  • Page 84 EXTERIOR LIGHTING AND SIGNALS (2/5) See-me-home lighting Automatic operation (depending on vehicle) function With the engine running, the dipped This function (useful, for example, for beam headlights are switched on or off opening a gate, a garage, etc.) enables automatically depending on the level of you to switch on dipped headlights mo- ambient light, without the need to oper- mentarily.
  • Page 85 EXTERIOR LIGHTING AND SIGNALS (3/5) Cornering lights Automatic lighting with main beam headlights Depending on the vehicle, if the dipped beam headlights are on when corner- Depending on the vehicle, when you ing, and under certain driving condi- change to main beam headlights, the tions (speed, steering wheel angle, for- dipped beam headlight raise to improve wards gear selected, etc.), additional...
  • Page 86 EXTERIOR LIGHTING AND SIGNALS (4/5) Automatic operation (depending on Lights-on reminder buzzer vehicle) If the lights are switched on after the The lights go out when the engine engine is switched off, a warning is stopped, when the driver’s door is beep sounds when the driver’s door is opened or when the vehicle is locked.
  • Page 87: Front Fog Lights

    EXTERIOR LIGHTING AND SIGNALS (5/5) Rear fog light Switching off the lights Turn centre ring 5 on stalk 1 Turn ring 5 again until mark 6 is oppo- until the symbol faces mark 6, then re- site the symbol for the fog light you wish lease it.
  • Page 88: Electric Beam Height Adjustment

    ELECTRIC BEAM HEIGHT ADJUSTMENT Examples of positions for control A depending on the load All versions except Utility Commercial Estate and Estate vehicles vehicles Driver only Driver with one front passenger On vehicles fitted with this function, control A allows you to adjust the height Driver with one front of the beams according to the load.
  • Page 89 WINDSCREEN WASH/WIPE (1/2) Vehicles with automatic wiper function With the engine running, move stalk 1 – A park. – B automatic wiper function When this position is selected, the system detects the presence of water on the windscreen and triggers wiping at a suitable wiping speed.
  • Page 90: Windscreen Washer

    WINDSCREEN WASH/WIPE (2/2) In freezing or snowy weather, ensure they are not stuck to the windscreen (including the central area located behind the interior rear-view mirror) and the rear screen before starting the wipers (risk of motor overheat- ing). Check the condition of the wiper blades.
  • Page 91: Special Note

    REAR SCREEN WASH/WIPE Rear screen wash/wipe With the ignition on, turn the end of stalk 1 to align mark 2 with the symbol. In freezing or snowy weather, ensure When the stalk is released, it returns to they are not stuck to the windscreen the rear wipe position.
  • Page 92: Fuel Tank (Filling With Fuel)

    FUEL TANK (1/2) Useful capacity of the fuel tank: Fuel grade 55 litres approximately. Use a high grade fuel that complies The engine 1.2 TCe has a fuel tank with the standards currently in force in capacity of approximately 40 litres or each country.
  • Page 93: Filling Up With Fuel

    FUEL TANK (2/2) Petrol version Filling up with fuel Persistent fuel odour It is essential to use unleaded petrol. With the ignition switched off, insert the If you notice a persistent The octane rating (RON) must con- nozzle so that the valve is open and fuel odour you should: form with the specifications given on fully insert the nozzle before engaging...
  • Page 94 1.88...
  • Page 95 Starting/stopping the engine using the RENAULT card ........
  • Page 96: Running In

    RUNNING IN Petrol version Diesel version For the first 600 miles (1,000 km), do For the first 900 miles (1,500 km), not exceed 78 mph (130 km/h) in the do not exceed 2,500 rpm. After com- highest gear, or 3,000 to 3,500 rpm. pleting this mileage you may drive faster, although you may only expect You may only expect top performance...
  • Page 97 IGNITION SWITCH: vehicle with key Ignition position M. Special note on vehicles with an au- tomatic gearbox The ignition is switched on: Before starting, move the lever to posi- tion N or P. Start position D Special note on vehicles with a If the engine fails to start at the first Quickshift gearbox attempt, the key must be turned back...
  • Page 98: Starting The Engine

    STARTING/STOPPING THE ENGINE: vehicle with key É Starting the engine Diesel injection Stopping the engine Petrol injection With the engine idling, turn the key Cold or warm engine back to the Stop position. Engine warm or cold – Turn the key to the “Start” posi- –...
  • Page 99: Renault Card

    STARTING THE ENGINE: vehicle with RENAULT CARD (1/3) RENAULT card Starting conditions. The card must be in detection zone 1 Follow the starting instructions on the (passenger compartment and luggage instrument panel 2 describing the fol- Driver’s responsibility compartment, except for some high...
  • Page 100: All Vehicles

    STARTING THE ENGINE: vehicle with RENAULT CARD (2/3) Vehicles with an automatic Vehicles with a Quickshift – in some cases, it will be necessary to move the steering wheel while press- gearbox gearbox ing start button 3 to assist in unlock-...
  • Page 101 STARTING THE ENGINE: vehicle with RENAULT CARD (3/3) – when the RENAULT card battery is drained, flat battery, etc. The messages “card not detected” then “insert card” appear on instrument panel 2. Move the RENAULT card or insert it fully into card reader 4.
  • Page 102 STOPPING THE ENGINE: vehicle with RENAULT CARD When you leave your vehi- cle, especially if you have your RENAULT card with you, check that the engine is completely switched off. Driver’s responsibility Never leave your vehicle with the RENAULT card...
  • Page 103: Special Features Of Petrol Versions

    SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
  • Page 104: Special Features Of Diesel Versions

    SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection To avoid faults in icy weather: equipment which prevents the engine – ensure that the battery is always fully speed being exceeded irrespective of charged;...
  • Page 105 DIESEL VERSIONS WITH PARTICLE FILTER As a guide, this type of cleaning should When driving, depending on the grade take up to 20 minutes. of fuel used, it is possible that white © smoke may be emitted. If the warning light comes on, This is due to the exhaust particle filter accompanied by the message “Check being cleaned automatically, and does...
  • Page 106: Gear Lever/Handbrake

    GEAR LEVER/HANDBRAkE Handbrake To release: Pull lever 2 up slightly, press button 3 and then lower the lever to the floor. The red warning light on the instrument panel will light up if you are driving with an incorrectly released handbrake. To apply: Pull lever 2 upwards.
  • Page 107: Engine Adjustments

    ADVICE: antipollution, fuel economy and driving (1/3) Aiding fuel economy Your vehicle complies with criteria for Have your vehicle adjusted and recycling and recovering vehicles at the checked by an approved Dealer, in ac- Depending on the vehicle, in order to end of their service life which will come cordance with the instructions given in optimise consumption, an indicator light...
  • Page 108 ADVICE: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring – Avoid sudden acceleration. – Brake as little as possible. If you an- system ticipate an obstacle or bend in ad- The exhaust gas monitoring system will vance, you may then simply release detect any operating faults in the vehi- the accelerator pedal.
  • Page 109 ADVICE: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
  • Page 110: Environment

    This commitment is illustrated by the less fuel (eg. 140 g/km, equivalent to the vehicle components have been de- Renault eco² group signature. 5.3 l/100 km for a diesel vehicle). signed to enable them to be recycled. Our vehicles are also equipped with a...
  • Page 111: Anti-Lock Braking System: Abs

    ANTI-LOCk BRAkING SYSTEM: ABS (1/2) Under heavy braking, the essential re- This system also allows you to optimise You will feel a pulsation through the quirements are to limit the stopping stopping distances when the grip of one brake pedal each time the system is ac- distance and keep your vehicle under or more wheels may be lost (wet roads, tivated.
  • Page 112 ANTI-LOCk BRAkING SYSTEM: ABS (2/2) One of two situations may arise if there is a fault in the ABS system: 1 – The orange warning lights © light up on the instru- ment panel. Braking is still performed, but with- out the ABS system.
  • Page 113: Electronic Stability Programme: Esp

    ELECTRONIC STABILITY PROGRAM: E.S.P. (1/2) This system helps to keep control of When the E.S.P. function starts operat- the vehicle in critical driving situations ing, warning light A flashes to warn you. (avoiding an obstacle, loss of grip when If the warning light comes on accompa- cornering, etc.) and works in conjunc- nied by the ‘traction control deselected’...
  • Page 114 ELECTRONIC STABILITY PROGRAM: E.S.P. (2/2) Disabling the function The function is deactivated by pressing switch 1; warning light A will come on to warn you that the system has been deactivated. This action also deactivates the trac- tion control mechanism: the message ‘ASR deselected’...
  • Page 115: Traction Control: A.s.r

    TRACTION CONTROL: A.S.R. (1/2) This system helps to limit skidding on The system also adjusts the engine drive wheels and to control the vehicle speed to the grip available under the when pulling away or accelerating. wheels, independently of the pressure exerted on the accelerator pedal.
  • Page 116 TRACTION CONTROL: A.S.R. (2/2) Disabling the function In some situations (driving on very wet ground: snow, mud, etc. or driving with snow chains fitted), the system may reduce the engine output to limit wheel- spin. If this is not required, it is possible to deactivate the function by pressing switch 1.
  • Page 117: Emergency Brake Assist

    EMERGENCY BRAkE ASSIST This system supplements the ABS and helps reduce vehicle stopping dis- tances. Operating principle The system is for detecting an emer- gency braking situation. In this case, the braking assistance immediately de- velops maximum power and may trig- ger ABS regulation.
  • Page 118: Indicator Light

    CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) Ð Controls Indicator light 6 The speed limiter function helps you stay within the driving speed limit that 1 Main “On/Off” switch. This indicator light on the in- you choose. strument panel lights up to indicate that 2 Limit speed activation, storage and This may be useful, for example, driving the limiter function is in operation.
  • Page 119 CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Driving When a limit speed has been stored, if this speed is not reached the vehicle behaves in a similar way to those with- out the speed limiter function. From this point, no effort on the accel- erator pedal will allow you to exceed the programmed speed except in an emergency (refer to information on...
  • Page 120: Speed Limiter

    CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Exceeding the limit speed Recalling the limit speed In the event of an emergency A stored speed can be recalled by pressing switch 5 (R) until the message It is possible to exceed the limit speed “Speed limiter”...
  • Page 121 CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. Therefore, it can under no circum- Controls The cruise control function helps you to stances replace the driver’s respon- maintain your driving speed at a speed sibility to respect speed limits and to...
  • Page 122: Cruise Control

    CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Activating cruise control Driving Switching on At a steady speed (above 20 mph Once a cruising speed is stored and Press switch 1 on the side showing (30 km/h) approximately) press the cruise control function is active, Ï...
  • Page 123 CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed In the event of an emergency The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel.
  • Page 124 CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Recalling the cruising speed If a speed has been stored, it is possi- ble to recall it by pressing switch 5 (R), on condition that you are driving faster than 20 mph (30 km/h) and that you are sure that the driving conditions are suitable (traffic, road surface condition, weather conditions, etc.).
  • Page 125: Selector Lever

    AUTOMATIC TRANSMISSION (1/3) Driving in automatic mode Move lever 1 to position D. In most traffic conditions, you will not have to touch the gear selector lever again: the gears will change automati- cally at the right time and at the most suitable engine speed because the au- tomatic system takes into account the vehicle load and road contour and ad-...
  • Page 126 AUTOMATIC TRANSMISSION (2/3) – If the road contour and bends in the road do not allow you to stay in automatic mode (e.g.: in mountain- ous areas), it is recommended that you switch to manual mode. This will prevent the automatic gear- box from changing gears repeatedly when climbing, and permit engine braking on long descents.
  • Page 127: Automatic Transmission

    AUTOMATIC TRANSMISSION (3/3) Parking the vehicle Operating faults When the vehicle is stopped, move the – when driving, if the ‘check gearbox’ lever to position P while keeping your message appears on the instrument foot on the brake pedal: the gearbox is panel, it indicates a fault.
  • Page 128: Quickshift Gearbox

    QUICkSHIFT GEARBOX (1/5) Selector lever 1 Gear shift pattern Display – This allows you to engage first gear, A/M to change mode (automatic/ 2 automatic mode to select reverse and neutral and to manual) 3 selected gear display change gear in manual mode. to change up a gear 4 brake pedal depressed indicator light - to change down...
  • Page 129 QUICkSHIFT GEARBOX (2/5) Operation Starting Switch on the ignition. The display shows N (neutral) and A The display on the instrument panel (automatic mode). switches on. If neutral (N) is displayed, Moving off forwards start the engine but do not depress the accelerator.
  • Page 130 QUICkSHIFT GEARBOX (3/5) Driving in automatic mode Changing mode Accelerating and overtaking Each time the ignition is switched on, You can change mode at any time To obtain maximum vehicle perform- automatic mode is selected by default by pushing the lever to the left. This ance, in automatic or manual mode se- (letter A on the display).
  • Page 131 QUICkSHIFT GEARBOX (4/5) Parking To park the vehicle with a gear en- gaged (on a slope, for example): before switching off the engine, check that a gear other than N is displayed on the instrument panel. The next time the engine is started, de- press the brake pedal.
  • Page 132 QUICkSHIFT GEARBOX (5/5) Operating faults The vehicle will not start If you cannot start the engine and if the ‘Check gearbox’ battery is not discharged (display lit up): If, when driving, the message “Check – switch on the ignition, © gearbox”...
  • Page 133: Parking Distance Control

    PARkING DISTANCE CONTROL (1/2) Operating principle Ultrasonic sensors, fitted in the vehi- cle’s rear bumper, measure the dis- tance between the vehicle and an ob- stacle when reversing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when This function is an addi- the vehicle is approximately 30 centi-...
  • Page 134 PARkING DISTANCE CONTROL (2/2) Prolonged deactivation of the system You can deactivate the system for pro- longed periods by pressing the switch for longer than approximately three seconds. The warning light built into the switch remains lit constantly. Once deactivated, the system can be reactivated by pressing the button again for longer than approximately three seconds.
  • Page 135: Your Comfort

    Section 3: Your comfort Air vents............... Heating and air conditioning .
  • Page 136: Air Vents

    air vents, air outlets (1/2) 5 control panel. 6 right-hand side air vent. 7 right-hand side window demister vent. 8 passenger footwell heater outlets. 1 left-hand side window demister vent. 2 left-hand side air vent. 3 windscreen demisting vents. 4 centre air vents.
  • Page 137: Air Flow

    air vents, air outlets (2/2) To remove bad odours from your ve- hicles, only use the systems designed for this purpose. Consult an approved Dealer. air flow Direction Move the control knob 1 or 3 (beyond Right/left: move tabs 2 or 4. the resistance point).
  • Page 138: Heating And Air Conditioning

    HeatinG, air COnDitiOninG (1/4) the controls E Heated rear screen and heated door mirror control and indicator light (depending on vehicle). A Adjusting the passenger compart- ment air distribution. F Air conditioning operation control and indicator light (depending on B Air temperature adjustment. vehicle).
  • Page 139: Passenger Compartment

    HeatinG, air COnDitiOninG (2/4) The air flow is shared between the side window and wind- screen demisting vents and the pas- senger footwells. This is the recommended position for the best temperature in cold weather. The air flow is directed mainly towards the footwells.
  • Page 140 HeatinG, air COnDitiOninG (3/4) adjusting the air temperature Turn control B to obtain the desired temperature. The further the pointer is in the red, the more the temperature will be increased. switching air conditioning on or off The air conditioning is switched on (in- dicator light illuminated) or off (indicator light extinguished) using button F.
  • Page 141 HeatinG, air COnDitiOninG (4/4) rear screen de-icing/ demisting With the engine running, press button E. The operating tell-tale comes This function permits rapid demisting/ de-icing of the rear screen and de-icing of the door mirrors (on equipped vehi- cles). to exit this function, press button E again.
  • Page 142: Automatic Climate Control

    aUtOMatiC CLiMate COntrOL (1/8) 12 Heated rear screen and heated door mirrors (depending on vehi- cle). 13 Heated rear screen indicator light. 14 Air recirculation control. information and advice on use: refer to information on “Air conditioning: in- formation and advice on use”. the controls 5 Display.
  • Page 143 aUtOMatiC CLiMate COntrOL (2/8) The automatic heating and air con- ditioning system guarantees com- fort in the passenger compartment and good visibility (except in the event of extreme conditions), while optimising consumption. this is the recommended mode of use. ambient temperature : –...
  • Page 144 aUtOMatiC CLiMate COntrOL (3/8) ambient temperature: adjusting automatic mode automatic mode (continued) The automatic mode is the system’s normal operating mode (AUTO light on) Operation but you may alter the selections made To reach and keep the chosen comfort by the system (air distribution, etc.). level and to maintain good visibility, the These options are explained on the fol- system controls:...
  • Page 145 aUtOMatiC CLiMate COntrOL (4/8) The air flow is directed towards the dashboard vents and the footwells. The air flow is directed mainly towards the footwells. õ Distribution of air in the All the air flow is directed to the demisting vents for the wind- passenger compartment screen and the side windows.
  • Page 146 aUtOMatiC CLiMate COntrOL (5/8) varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. Automatic mode is switched off by pressing buttons 9 and 11. These buttons allow you to increase or decrease ventilation speed.
  • Page 147 aUtOMatiC CLiMate COntrOL (6/8) rear screen De-icing / to exit this function, press button 12 again. Demisting automatically stops Demisting by default. With the engine running, press button 12. The operating tell-tale 13 comes on. This function permits rapid demisting/ de-icing of the rear screen and de-icing of the door mirrors (on equipped vehi- cles).
  • Page 148 aUtOMatiC CLiMate COntrOL (7/8) note: if you wish to reduce the air flow (which may produce a certain amount of noise in the passenger compart- ment), press button 11. to exit this function, press either: – button 1 again; – button 6 (the AUTO indicator light on the display will light up).
  • Page 149: Air Recirculation Mode

    aUtOMatiC CLiMate COntrOL (8/8) air recirculation mode Prolonged use of the air recirculation mode may cause the windows to mist Pressing button 14 activates air recir- up or lead to odours, as the air is not culation (the symbol lights up on the renewed.
  • Page 150: Air Conditioning: Information And Advice On Use

    air COnDitiOninG: information and advice on use Do not add anything to the vehicle’s ventilation circuit (for example, to remove bad odours). Operating faults there is a risk of damage or of As a general rule, contact your ap- Fuel consumption fire.
  • Page 151: Electric Windows

    From the driver’s seat Driver’s responsibility Never leave your vehicle with the RENAULT card inside and never leave a child Operate the switches as follows: (or a pet) unsupervised, even for a short while. They may pose a risk to them- –...
  • Page 152 Driver’s responsibility Never leave your vehicle with the From the rear seats One-touch mode RENAULT card inside and never leave a child (or a pet) unsuper- Press switch 7. This is an additional function to the vised, even for a short while. They electric windows.
  • Page 153 eLeCtriC WinDOWs /ManUaL WinDOWs (3/3) One-touch mode normal mode – Briefly press the relevant switch – Press the relevant switch to lower fully: the window is lowered com- the window and release it when the pletely. window is at the required height. –...
  • Page 154: Electric Sunroof

    When parking in direct sunlight, we advise you to pull down the sun blinds. Driver’s responsibility Never leave your vehicle with the RENAULT card or remote control inside and never leave a child (or a pet) unsu- tilting the sunroof the system operates: pervised, even for a short while.
  • Page 155 eLeCtriC sUnrOOF (2/2) special note Precautions during use For your safety your vehicle is fitted – check that the sunroof is properly with an anti-pinch function. When a closed before leaving your vehicle; window encounters resistance whilst – clean the seal every three months closing (someone’s fingers, an animal’s using products recommended by our paw or the branch of a tree, for exam-...
  • Page 156: Sun Visor

    sUn visOr Front sun visor rear sun blind Lower sun visor 1. Pull the sun blind upwards using the tab until both hooks 3 lock into their hous- ings (make sure the blind is properly Courtesy mirrors locked in position). Slide cover 2.
  • Page 157: Interior Lighting

    interiOr LiGHtinG Map reading lights (depending on vehicle) Press switch 1 for the driver, 3 for the front passenger. Courtesy light Driver and passenger underfloor storage Press switch 2 for: compartment lights 4 – permanent lighting; (depending on vehicle) – intermittent lighting, which comes on when a door is opened.
  • Page 158 PassenGer COMPartMent stOraGe/FittinGs (1/4) Front door storage pockets 1 sunglasses holder 2 They can hold a 1.5 litre bottle. Nothing should be placed Ensure that no hard, heavy on the floor area in front of or pointed objects are the driver as such objects placed in the “open”...
  • Page 159 PassenGer COMPartMent stOraGe/FittinGs (2/4) Clip 3 Centre console storage compartment 4 or 5 This can be used for storing motorway tickets, cards, etc. This can be used for storing a mobile ashtray, cup holder, etc. When turning corners, accelerating or braking, ensure that the recepta- cle being held by the cup holder is not dislodged.
  • Page 160 PassenGer COMPartMent stOraGe/FittinGs (3/4) rear door storage rear door storage Passenger storage compartment 6 compartment 7 compartment 8 Pull handle 9 to open it. Depending on the vehicle, this storage compartment is ventilated and air con- ditioned in the same way as the pas- senger compartment.
  • Page 161 PassenGer COMPartMent stOraGe/FittinGs (4/4) Front seat storage Grab handle 11 compartments 10 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. 3.27...
  • Page 162: Cigar Lighter

    asHtraY/CiGar LiGHter ashtray 1 Cigar lighter 3 It can be housed in either position 2 With the ignition on, push in the cigar or 4. lighter 3. It will spring back with a click when it is ready. Pull it out to use. After use, re- place it without pushing it all the way in.
  • Page 163 rear HeaD rests Positions for use to remove the headrest While pressing button A of lock 1, lift Press button A of lock 1 and remove the headrest fully to use it in the top po- the headrest. sition. Lower it until it locks to use it in the bottom position.
  • Page 164: Rear Bench Seat: Functions

    rear BenCH seat: functions (1/2) The seat base and the seatback may Then lift up the rear section of cushion to fold down the seatback be folded down (one or both sections) 1 and tilt the seat base so that it is next remove the rear headrests (if fitted).
  • Page 165 rear BenCH seat: functions (2/2) When moving the rear seats, ensure that nothing obstructs the anchorage points (passenger’s arm or leg, a pet, gravel, cloth, toys, etc.). sport tourer version to replace the seat base, proceed in the reverse order to removal. to replace the seatback, proceed in the reverse order to removal.
  • Page 166: Rear Parcel Shelf

    BOOt/rear ParCeL sHeLF rear parcel shelf to open Press button 1 and lift the tailgate. To remove: – unhook both straps 2; to close – unhook sun visor 3 (depending on Lower the boot lid. vehicle); Maximum weight on rear parcel shelf: 25 kg, evenly distributed.
  • Page 167: Luggage Cover

    LUGGaGe COMPartMent COver: sport tourer versions to remove the flexible removing the luggage Luggage compartment cover section A of the luggage compartment cover 1 storage 1 compartment cover 1 Press button 3 and lift the right-hand Lift the mobile floor B. side of the roller at the same time.
  • Page 168 LUGGaGe COMPartMent COver: utility versions The luggage compartment cover con- the luggage compartment cover is the luggage compartment cover is sists of a rigid section A and a folding in the folded position. removed. section B. To fold it: To remove it: with the cover in the folded the luggage cover is in the unfolded position and holding it horizontally: –...
  • Page 169: Luggage Compartment Storage

    LUGGaGe COMPartMent stOraGe (1/2) Locations for anchorage sport tourer versions rings 1 On equipped vehicles, remove the mobile floor to access the rings (refer to Useful for securing objects transported the information on “mobile floor”). in the luggage compartment. See the information on “Transporting objects in the luggage compartment”.
  • Page 170 LUGGaGe COMPartMent stOraGe (2/2) Mobile floor First storage second storage – Lift section 3 and fold it against sec- – Lift section 3 and fold it against sec- When fitted to the vehicle, it can be tion 2; tion 2; used to make loading easier.
  • Page 171: Transporting Objects In The Luggage Compartment

    transPOrtinG OBJeCts in tHe LUGGaGe COMPartMent If you have to place objects on the Always position the objects transported folded seatback, with the bench seat in so that the largest surface is against: the 3-seater position, remove the front headrests before folding the seatback so that is can be folded as flat as pos- sible against the seat base.
  • Page 172: Luggage Net

    LUGGaGe net (1/2) Luggage net A Fitting the luggage net – move the cut-out in the carpet to access lower mounting 3 for the net; behind the front seats On equipped vehicles, this can be used – once you have accessed the lower when transporting animals or luggage, Inside the vehicle on each side: mounting, attach the hook of the net...
  • Page 173 LUGGaGe net (2/2) Fitting the luggage net A Marking – in the luggage compartment, it is essential to fit the lower mounting behind the rear bench seat A marking on the luggage retaining trim strap hook on the net to the anchor- indicates the location of the ISOFIX Inside the vehicle on each side: ing hook 4 identified by the mark-...
  • Page 174: Roof Bars/Spoiler

    rOOF Bars (1/2) sport tourer versions When fitting roof bars, replace the blanking bolts with the mounting bolts The roof bars are fixed and should not supplied with the roof bars. be removed. To change them contact an approved Dealer. access to mounting points for five-door versions Open the doors.
  • Page 175 rOOF Bars (2/2)/sPOiLer Precautions during use Handling the tailgate Before handling the tailgate, check the objects and/or accessories (bike rack, roof box, etc.) fitted to the roof bars: these must be correctly positioned and secured, so as not to hinder the opera- tion of the tailgate.
  • Page 176: Hands-Free Telephone Integrated Control

    HanDs-Free teLePHOne inteGrateD COntrOL telephone holder 1 steering wheel controls 2 Position for microphone 3 Using the telephone As each telephone has its own tech- Refer to the relevant instructions for We remind you of the need nical specifications, it is essen- information on how to operate this to conform to the legislation tial to select the correct holder for...
  • Page 177 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .
  • Page 178: Bonnet

    BONNET (1/2) Unlocking the bonnet catch To open the bonnet, pull the handle 1. To open, push tab 2 to the left as you open the bonnet. Opening the bonnet Lift the bonnet and release stay 4 from its holder 5. For your own safety, it is very important to fix the stay into re- tainer 3 in the bonnet.
  • Page 179: Closing The Bonnet

    BONNET (2/2) Closing the bonnet Before closing the bonnet, make sure that nothing has been left in the engine compartment. To close the bonnet, replace stay 4 in holder 5. Hold the middle of the bonnet and guide it down to one foot (30 cm) above the closed position, then re- lease.
  • Page 180: Engine Oil Level: General Information

    ENGINE OIL LEVEL: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts Variant 1 Variant 2 Interpretation of messages and it is normal to top up the level be- tween oil changes. OIL LEVEL Message 1 However, contact your approved...
  • Page 181 ENGINE OIL LEVEL: general information (2/2) Reading the level using the dipstick – take out the dipstick; Consult your approved dealer at – wipe the dipstick using a clean, lint- once if you notice an abnormal or free cloth; repeated drop in any of the fluid –...
  • Page 182: Engine Oil Level: Topping Up/Filling

    ENGINE OIL LEVEL: topping up/filling (1/2) Topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...
  • Page 183 ENGINE OIL LEVEL: topping up/filling (2/2) Engine oil grade Filling: take care when Refer to the Maintenance Service topping up the oil that Booklet for your vehicle. no oil drips onto engine components - risk of fire. Remember to refit the cap securely as there is a risk of fire if oil splashes onto hot engine components.
  • Page 184: Levels

    LEVELS (1/3) Frequency of checking coolant level Replacement interval Check the coolant level regularly Refer to the Maintenance Service (very severe damage is likely to be Booklet for your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure:...
  • Page 185: Brake Fluid Level

    LEVELS (2/3) Level 1 It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI" warn- ing line. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from the manufacturer’s net- work or web site.
  • Page 186: Filters

    LEVELS /FILTERS (3/3) Filters The replacement of filter components (air filter, cabin filter, diesel filter, etc.) is scheduled in the maintenance opera- tions for your vehicle. Replacement intervals for filter el- ements: refer to the Maintenance Service Booklet for your vehicle. Windscreen/headlight washer Jets reservoir...
  • Page 187: Tyre Pressure

    TyRE pRESSURE Tyre safety and use of snow chains Refer to the information on “Tyres” in Section 5 for the servicing con- ditions and, depending on the ver- sion, the use of chains. Special note For vehicles used fully laden (maximum permissible all-up...
  • Page 188: Battery

    BATTERy Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. This is located under cover 1 and does Label A not need to be serviced. Observe the indications on the battery: – 2 naked flames and smoking forbid- den;...
  • Page 189: Bodywork Maintenance

    BODyWORK MAINTENANCE (1/2) Minor impacts A well-maintained vehicle will last Allow rust to form following minor im- longer. It is therefore recommended to pacts. You should take a minimum number of maintain the exterior of the vehicle reg- precautions in order to safeguard your Use solvents not approved by our ularly.
  • Page 190 BODyWORK MAINTENANCE (2/2) you should – bird droppings, which cause a If it is necessary to clean mechani- chemical reaction with the paint that cal components, hinges, etc., spray Observe the vehicle stopping distances rapidly discolours paintwork and them with products approved by our when driving on gravelled surfaces to may even cause the paint to peel Technical Department to protect them...
  • Page 191: Interior Trim Maintenance

    INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
  • Page 192 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable you should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
  • Page 193: Practical Advice

    RENAULT card: battery ........
  • Page 194 PUNCTURE, EMERGENCY SPARE WHEEL (1/4) In case of puncture Depending on the vehicle, a tyre infla- tion kit or emergency spare wheel is provided (refer to the following pages). If the emergency spare wheel has been stored for several years, have it checked by your Dealer to ensure that it is safe to use.
  • Page 195: Emergency Spare Wheel

    PUNCTURE, EMERGENCY SPARE WHEEL (2/4) Emergency spare wheel – unscrew nut 5 in an anti-clockwise – pull the wheel towards you, direction until it comes off com- – lay the wheel down flat and unfasten – Open the tailgate; pletely, then place the palm of your cable 7 from its housing 8.
  • Page 196 PUNCTURE, EMERGENCY SPARE WHEEL (3/4) To refit a wheel After changing a wheel, position the Position yourself behind the vehicle and replaced wheel on support 9, with the pull handle 6 to raise the wheel until it is To carry out this operation, the cable valve facing the ground.
  • Page 197: Special Features

    PUNCTURE, EMERGENCY SPARE WHEEL (4/4) Note: if the tool kit does not lock in place, check the tightness of nut 5 and the correct positioning of the handle 6. Special features The emergency spare wheel holder should always be present when you are driving even when the wheel itself is not present: risk of water entering the ve- hicle.
  • Page 198 TYRE PRESSURE KIT (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
  • Page 199 TYRE PRESSURE KIT (2/3) Open the kit, remove the caps 1 and 4 (it is essential not to remove the burst- ing disc from the bottle) and screw bottle 2 in place of cap 4. With the engine running and the parking brake applied, –...
  • Page 200 TYRE PRESSURE KIT (3/3) Precautions when using the Affix the driving recommendation label to the dashboard where it can easily be seen by the driver; The kit should not be operated for more Put the kit away. than 15 consecutive minutes. At the end of this initial inflation opera- Please be aware that a tion, air will still escape from the tyre.
  • Page 201: Tool Kit

    TOOL KIT End piece for special wheel bolt 3 Towing hitch 4 Refer to the information on “Towing” in Section 5. Hubcap tool 5 or 6 This tool is used to remove the wheel trims. Jack 7 Remove jack 7. To refit, lower the jack fully and unscrew Storage compartment 1 The tools included in the tool kit depend...
  • Page 202: Wheel Trims - Wheel

    WHEEL TRIMS - WHEEL Do not leave the tools un- secured inside the vehicle as they may come loose under braking. After use, Hubcap (example hubcap 1) Central wheel hubcap check that all the tools are correctly (example: hubcap 4) clipped into the tool kit, then position Remove the wheel trim using hubcap it correctly in its housing: there is a...
  • Page 203: Changing A Wheel

    CHANGING A WHEEL (1/2) Continue to crank the jack so that the baseplate is correctly positioned (it should be underneath the vehicle and aligned with jack head A). Turn it a few times to lift the wheel off the ground. Vehicles equipped with a jack Switch on the hazard warn- and wheelbrace...
  • Page 204 CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub. Tighten the bolts and lower the jack. With the wheel on the ground, tighten the screws as fully as possible and check the tightness as soon as possi-...
  • Page 205: Tyres (Tyre And Wheel Safety, Use In Winter)

    TYRES (1/3) Tyre and wheel safety When the tyre tread has been worn to the level of the warning strips, they The tyres are the only contact between become visible 2: it is then neces- the vehicle and the road, so it is essen- sary to replace your tyres because the tial to keep them in good condition.
  • Page 206: Tyre Pressures

    TYRES (2/3) Tyre pressures Emergency spare wheel Pressures should be checked when the tyres are cold; ignore higher pressures Adhere to the tyre pressures (including Refer to the information on the which may be reached in hot weather the emergency spare wheel). The tyre “Emergency spare wheel”...
  • Page 207 TYRES (3/3) Use in winter Snow or Winter tyres Studded tyres We would recommend that these be This type of equipment may only be Chains fitted to all four wheels to ensure that used for a limited period and as laid For safety reasons, fitting snow your vehicle retains maximum road down by local legislation.
  • Page 208 HALOGEN HEADLIGHTS: changing bulbs (1/3) It is essential to use anti-U.V. 55W bulbs so as not to damage the plastic on the headlights. Do not touch the bulb glass. Hold it by its base. Mark the bulb’s position before removal to ensure correct positioning when re- placing.
  • Page 209 HALOGEN HEADLIGHTS: changing bulbs (2/3) It is essential to use anti-U.V. 55W bulbs so as not to damage the plastic on the headlights. Do not touch the bulb glass. Hold it by its base. Mark the bulb’s position before removal to ensure correct positioning when re- placing.
  • Page 210 HALOGEN HEADLIGHTS: changing bulbs (3/3) Front side light Direction indicator lights Additional cornering light Remove cover E, then pull bulb holder 6 Turn bulb holder F a quarter of a turn Due to their reduced accessibility to access the bulb. and take out the bulb.
  • Page 211: Headlights (Changing Bulbs)

    HEADLIGHTS: additional/front fog lights Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved Dealer. Front fog lights 1 Changing a bulb: Consult an approved Dealer. Bulb type: H11. Any operation on (or modi- fication to) the electrical system must be performed by an approved dealer...
  • Page 212: Rear Lights And Side Lights: Changing Bulbs

    REAR LIGHTS AND SIDE LIGHTS: changing bulbs (1/4) 3 and 5 door versions Release the rear light assembly from 3 Side lights and stop lights outside the vehicle by pulling towards Bulb type: P21/5W. After opening the tailgate, remove the rear. bolts 1.
  • Page 213 REAR LIGHTS AND SIDE LIGHTS: changing bulbs (2/4) Sport tourer Versions Release the rear light assembly from 3 Direction indicator lights outside the vehicle by pulling towards Bulb type: P21W. After opening the tailgate, unscrew the rear. bolts 1. 4 Side light and brake light Remove the clips 2 from the bulb holder Bulb type: P21/5W.
  • Page 214 REAR LIGHTS AND SIDE LIGHTS: changing bulbs (3/4) Rear fog lights 6 High level brake light 7 Unclip the light using a flat-blade screw- Consult an approved dealer. driver or similar (at mark A for three and five door versions). 6 Rear fog light Bulb type: P21W.
  • Page 215 REAR LIGHTS AND SIDE LIGHTS: changing bulbs (4/4) Number plate lights 8 Sport tourer versions Side-mounted indicator lights 9 3 and 5 door versions Unclip light 8 by pressing the tab. Unclip the side mounted indicator light Unclip light 8 by pressing the tab. Remove the light cover to gain access (using a flat-blade screwdriver or simi- to the bulb.
  • Page 216: Interior Lighting: Changing Bulbs

    INTERIOR LIGHTING: changing bulbs (1/2) Courtesy light Door lights 2 Unclip the lens (using a flat-blade Unclip the light and remove the bulb screwdriver or similar). using a pen or a flat-blade screwdriver. Remove the bulb concerned. Bulb type: C5W. Bulb type 1: W5W.
  • Page 217: Luggage Compartment Light

    INTERIOR LIGHTING: changing bulbs (2/2) Luggage compartment light Press tab 4 to release the bulb holder and gain access to bulb 5. Unclip light 3 by pressing the tabs on Bulb type: C5W festoon type bulb. each side (using a flat-blade screw- driver or similar).
  • Page 218: Fuses

    FUSES (1/2) In accordance with local legislation or as a precautionary measure: obtain an emergency kit containing a set of spare bulbs and fuses from an approved Dealer. Fuse box 1 Remove the fuse using tweezers 2, lo- cated on the cover. If any electrical component does not To remove the fuse from the tweezers, work, check the condition of the fuses.
  • Page 219 FUSES (2/2) Allocation of fuses (the presence of certain fuse depends on the vehicle equipment level) Some accessories are protected by Symbol Allocation Symbol Allocation fuses located in the engine compart- ment. Rear door locking/child However, due to their reduced acces- Climate control safety sibility, we advise you to have your...
  • Page 220 BATTERY: troubleshooting (1/4) To avoid all risk of sparks: – ensure that any consumers are switched off before disconnecting or reconnecting the battery; – when charging, stop the charger before connecting or disconnecting the battery; – to avoid creating a short circuit be- tween the terminals, do not place metal objects on the battery;...
  • Page 221 BATTERY: troubleshooting (2/4) Depending on the battery, reposition block A in the runners and slide it until it is positioned between the two marks 1. Pull block A slightly to the right to clip it on pin E, press, and check that it locks properly.
  • Page 222: Connecting A Battery Charger

    BATTERY: troubleshooting (3/4) Connecting a battery charger Have the battery’s charge status If your vehicle is to be left stationary for checked regularly: a relatively long time, disconnect the The battery charger must be com- battery or have it recharged regularly, –...
  • Page 223: Battery

    BATTERY: troubleshooting (4/4) Starting the vehicle using the battery from another vehicle Proceed as follows when starting your vehicle from another vehicle’s battery: Obtain suitable jump leads (large) from an approved Dealer or, if you already have jump leads, ensure that they are in perfect condition.
  • Page 224 RADIO FREQUENCY REMOTE CONTROL: battery Remote controls A and B Note: It is not advisable to touch the electrical circuit in the key cover when Replacing the battery replacing the battery. Remove screw 1, open the case at slot 2 using a coin, and replace the bat- tery 3, observing the type and polarity shown on the back of the cover.
  • Page 225: Renault Card: Battery

    RENAULT CARD: battery Replacing the battery The message “Change card battery” appears on the instrument panel. Pull firmly on emergency key 2. Replace battery 1, observing the type and polarity shown on the emergency key. After the procedure, the “Change card battery”...
  • Page 226 FITTING A RADIO – In all cases, it is very important to follow the manufacturer’s instruc- tions carefully. – The specifications of the brack- Radio location 1 Door speakers ets and wires (available from our network) vary depending on the Unclip the blanking cover.
  • Page 227: Accessories

    ACCESSORIES Before fitting an electrical or If you are using an anti-theft electronic device (particu- device, only attach it to the larly for transmitters/receiv- brake pedal. ers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle.
  • Page 228: Windscreen Wiper Blades

    WINDSCREEN WIPER BLADES (1/2) Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...
  • Page 229 WINDSCREEN WIPER BLADES (2/2) To refit To refit the wiper blade, proceed in re- verse order to removal. Make sure that the blade is correctly locked in position. Rear screen wiper blade 5 – In frosty weather, make sure that the wiper blades –...
  • Page 230: Towing: Breakdown

    TOWING: breakdown (1/3) Insert the key in the ignition switch, or the card in the reader, to unlock the steering wheel and use the signalling lights (brake lights, hazard warning lights, etc.). The towed vehicle’s lights must be switched on at night. The speed specified by current legis- lation for towing must always be ob- served.
  • Page 231: Towing

    With the engine switched off: the erational. transmission is no longer lubricated. It If it is locked, insert the RENAULT card is preferable to tow this type of vehi- into the reader and press the Start/Stop cle on a trailer or tow it with the front button for five seconds without press- wheels off the ground.
  • Page 232 TOWING: breakdown /ATTACHMENTS (3/3) Towing a vehicle with a Quickshift gearbox If a gear is engaged: – with the ignition on, select neutral while depressing the brake pedal; – check that neutral is engaged (e.g. by pushing the vehicle); – switch off the ignition. The vehicle should always be towed with the ignition switched off.
  • Page 233: Operating Faults

    Using the RENAULT card POSSIBLE CAUSES ACTION REQUIRED The RENAULT card does not lock or Card battery is flat. Use the emergency key (refer to the in- unlock the doors. formation on the Emergency key in Section 1).
  • Page 234 OPERATING FAULTS (2/8) The starter is activated POSSIBLE CAUSES ACTION REQUIRED There is no response, the warning lights Discharged battery. Connect another battery to the faulty bat- fail to light up and the starter does not tery. turn. Battery unserviceable. Replace battery.
  • Page 235 Starting conditions are not fulfilled. Refer to the information on “Starting/ (vehicle with RENAULT card). stopping the engine” in Section 2. The hands-free RENAULT card is not de- Move the card inside the passenger tected. compartment. The hands-free RENAULT card does not Insert the card in the card reader in order work.
  • Page 236 OPERATING FAULTS (4/8) On the road POSSIBLE CAUSES ACTION REQUIRED White smoke from the exhaust. This is not necessarily a fault. Smoke Refer to the information on “Special fea- may be caused by regeneration of the tures of diesel versions” in Section 2. particle filter.
  • Page 237 OPERATING FAULTS (5/8) On the road POSSIBLE CAUSES ACTION REQUIRED Smoke under the bonnet. Short circuit or cooling circuit leak. Stop, switch off the ignition, stand away from the vehicle and contact an ap- proved Dealer. Coolant circuit fault. Consult an approved dealer. The oil pressure warning light comes on: –...
  • Page 238 OPERATING FAULTS (6/8) On the road POSSIBLE CAUSES ACTION REQUIRED Steering becomes heavy. – assistance overheating, Leave to cool. – weak or dead battery. Recharge or replace the battery. The engine overheats. The coolant tem- Coolant pump: belt stretched or broken. Stop the vehicle, switch off the engine perature warning light comes on (or the Engine cooling fan not working.
  • Page 239 OPERATING FAULTS (7/8) Electrical equipment POSSIBLE CAUSES ACTION REQUIRED The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Broken windscreen wiper fuse. Consult an approved dealer. Blown rear screen wiper fuse (intermit- Replace it. tent, permanently stopped).
  • Page 240 OPERATING FAULTS (8/8) Electrical equipment POSSIBLE CAUSES ACTION REQUIRED The headlights One only: – blown bulb, Replace the bulb. are not working. – disconnected wire or incorrectly-posi- Check and reconnect the wire or the con- tioned connector, nector. – faulty earth connection. See above.
  • Page 241: Technical Specifications

    Section 6: Technical specifications Vehicle identification plate ............Dimensions .
  • Page 242: Vehicle Identification Plate

    Vehicle identification plates 7 8 9 The information shown on vehicle iden- 5 Maximum permissible all-up tification plate A should be quoted on all weight, rear axle. correspondence or orders. 6 Technical specifications of the ve- hicle. Vehicle identification plate A 7 Vehicle paint reference.
  • Page 243: Engine Identification Plates

    enGine identification plates please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
  • Page 244: Dimensions

    diMensions (in metres) (1/2) saloon version 1,458 to 1,472 (1) 0,805 2,575 0,621 4,017 1,497* 1,450 to 1,470 (1) (1) Depending on vehicle and tyre size 2,025 * unladen...
  • Page 245 diMensions (in metres) (2/2) sport tourer versions 0,805 2,575 0,822 1,458 to 1,472 (1) 4,203 1,497* 1,450 to 1,470 (1) (1) Depending on vehicle and tyre size 2,025 * unladen...
  • Page 246: Engine Specifications

    enGine specifications Versions 1.2 16V 1.2 tce 1.6 16V 1.5 dci engine type D4F Turbo K9K Turbo (see engine plate) cubic capacity (cc) 1149 1598 1461 type of fuel It is essential that you use unleaded petrol of the octane rating Diesel: the label octane rating stated on the label inside the fuel filler flap.
  • Page 247: Towing Weights

    WeiGhts (in kg) the weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. consult your approved dealer. Maximum permissible all-up weight (MMac) Weights are indicated on the vehicle identification plate (refer to Maximum permissible all-up weight (MMta) the information on “Vehicle identification plates”...
  • Page 248: Replacement Parts And Repairs

    ReplaceMent paRts and RepaiRs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
  • Page 249: Service Sheets

    seRVice sheets (1/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 250 seRVice sheets (2/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 251 seRVice sheets (3/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 252 seRVice sheets (4/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 253 seRVice sheets (5/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 254 seRVice sheets (6/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 255: Anticorrosion Check

    anticoRRosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.15...
  • Page 256 anticoRRosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.16...
  • Page 257 anticoRRosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.17...
  • Page 258 anticoRRosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.18...
  • Page 259 anticoRRosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.19...
  • Page 260 anticoRRosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.20...
  • Page 261: Alphabetical Index

    AlphAbeticAl index (1/5) changing a bulb .............5.16 → 5.25 ABS ................ 2.17 – 2.18 changing a wheel............ 5.11 – 5.12 accessories................ 5.35 changing gear ............2.31 → 2.38 accessories socket ............3.28 child restraint/seat ......1.36 – 1.37, 1.39 → 1.48 additional methods of restraint .......... 1.35 child safety..1.2 – 1.3, 1.11, 1.13 – 1.14, 1.32, 1.36 – 1.37,  side protection ............. 1.34 1.39 → 1.48, 2.5, 3.17 → 3.19 to the front seat belts ........1.29 → 1.32 child seats..........1.36 – 1.37, 1.39 → 1.47...
  • Page 262 AlphAbeticAl index (2/5) fuel filler cap ............1.86 – 1.87 emergency brake assist............. 2.23 emergency braking ............2.23 fuel level ..............1.56 → 1.60 emergency key ..............1.8 fuel tank emergency spare wheel ..........5.2 → 5.5 capacity ................ 1.86 engine fuel tank capacity ............ 1.86 – 1.87 technical specifications ..........
  • Page 263 AlphAbeticAl index (3/5) side lights ........1.77, 5.16 → 5.18, 5.20 jack ..................5.9 lights-on warning buzzer........... 1.13, 1.80 load permitted on the roof............ 6.7 locking the doors .............1.2 → 1.18 keys ................1.2 → 1.5 luggage retaining net ..........3.38 – 3.39 levels ...............4.8 → 4.10 maintenance: levels: bodywork ............4.13 – 4.14 brake fluid ..............
  • Page 264 AlphAbeticAl index (4/5) RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.18 RENAULT card tailgate ............3.32, 3.35 → 3.37 battery ................5.33 tanks and reservoirs use ........... 1.7 → 1.12, 2.5 → 2.8 brake fluid ..............4.9 RENAULT card battery ............5.33 coolant ................4.8 replacement parts ..............6.8 tanks and reservoirs: reverse gear windscreen washer ............
  • Page 265 AlphAbeticAl index (5/5) variable power-assisted steering ........1.24 ventilation ..............3.2 → 3.16 warning buzzer ..............1.61 warning lights............1.56 → 1.65 washing ..............4.13 – 4.14 weights ................6.7 wheelbrace ................5.9 wheels (safety) ............5.13 → 5.15 windscreen washer ..........1.83 → 1.85 wiper blades ............5.36 – 5.37 wipers ..............1.83 → 1.85 blades ...............
  • Page 268 à999109023Rí î í ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

This manual is also suitable for:

Clio 3

Table of Contents