Download  Print this page

Rear Panel - American Audio Q-2411 User Manual And Reference Manual

American audio mixer user manual q-2411.
Hide thumbs

Advertisement

Q-2411™
33
32
21. GND (GROUND TERMINAL) - Be sure to connect turntable ground leads to either or both of
the two available ground terminals. This will reduce the humming and popping noises associated
with magnetic phono cartridges.
22. MICROPHONE 2 CONNECTOR - This jack is used to a connect a microphone to the mixer.
Connect you microphone via this 1/4 inch (6.3mm) jack. The volume output level for this microphone
will be controlled by its own respective CHANNEL KNOB (19).
23. CHANNEL LINE LEVEL SELECTOR SWITCHES - These switches are used to change the volt-
age line levels of there respected Phono / Aux RCA inputs jacks. When connecting turntables with
magnetic cartridges to these jacks be sure the corresponding switch is in the "PHONO" position,
and when using line level input devices be sure this switch is in the "AUX" position. Always be sure
main power is shut off before change the position of the Line Level Selector Switch.
24. CHANNEL 1: PHONO 1/AUX 1 INPUT - The type of input must directly reflect the selected
mode of the LINE LEVEL SELECTOR SWITCH (23). Turntables equipped with MM pickup cartridge
(All DJ turntable use MM pick-up cartridges) may be connected to these jacks as long as the LINE
LEVEL SELECTOR SWITCH (23) is in the "PHONO 1" position. CD players, Tape Decks and other
line level instruments may only be connected to these jacks as long as the LINE LEVEL SELEC-
TOR SWITCH (23) is in the "AUX 1" position. Never connect line level instruments (CD players, tape
decks, etc.) to these jacks when the LINE LEVEL SELECTOR SWITCH (23) is in the "PHONO 1" posi-
tion, THIS MAY SERIOUSLY DAMAGE YOUR MIXER! The red colored RCA jack represents the right
channel input and the white represents the left channel input. Input volume will be controlled by the
channel one fader. The channel SOURCE SELECTOR SWITCH (4) must be in the "Phono 1/Aux 1"
position, to monitor any source connected to these jacks.
CHANNEL 1: LINE 1 INPUT JACKS - DO NOT CONNECT TURNTABLES TO THESE JACKS!
CD players, Tape Decks and other line level instruments may be connected to these jacks. The red
colored RCA jack represents the right channel input and the white represents the left channel input.
Input volume will be controlled by channel one fader. The channel SOURCE SELECTOR SWITCH (4)
must be in the "Line 1" position, to monitor any source connected to these jacks.
25. CHANNEL 2: PHONO 2/AUX 2 INPUT - The type of input must directly reflect the selected
mode of the LINE LEVEL SELECTOR SWITCH (23). Turntables equipped with MM pickup cartridge
(All DJ turntable use MM pick-up cartridges) may be connected to these jacks as long as the LINE
LEVEL SELECTOR SWITCH (23) is in the "PHONO 2" position. CD players, Tape Decks and other
line level instruments may only be connected to these jacks as long as the LINE LEVEL SELEC-
TOR SWITCH (23) is in the "AUX 2" position. Never connect line level instruments (CD players, tape
decks, etc.) to these jacks when the LINE LEVEL SELECTOR SWITCH (23) is in the "PHONO 2" posi-
tion, THIS MAY SERIOUSLY DAMAGE YOUR MIXER! The red colored RCA jack represents the right
31
American Audio
- www.americanaudio.us - Q-2411™ Instruction Manual Page 11
©
®
REAR PANEL - CONTROLS AND FUNCTIONS
CH-4
2
1
LINE 5
30
29 28 27
26 23
SERIAL NO:
25
23
24
23
22
21

Advertisement

Table of Contents

   Also See for American Audio Q-2411

   Related Manuals for American Audio Q-2411

Comments to this Manuals

Symbols: 0
Latest comments: