Table of Contents
Advertisement
Quick Links
Installation and Operation Instructions for the following unitized outdoor camera models:
UNI-ONER / EP SERIES
Outdoor 24VAC Clear Dome
UNI-ONER580C2
UNI-ONER550C2
UNI-ONER520C2
UNI-ONEP580C2
UNI-ONEP550C2
UNI-ONEP520C2
Note: AC 24V power supply for the camera and the heater/blower is an installer/reseller
provided item. Please refer to page 3 Electrical Specifications for power consumption
details.
Note: Please note that to achieve the increased depth with the aspheric design for optimal
camera lens to capsule orientation, the capsule is slightly angled around the highest
section. This creates a "line', visible to the naked eye, around the upper most section
of the capsule. This "line" serves as the geometric center line used to insure proper
camera placement. It is not typically seen by the camera. However, this line maybe
visible in the camera image when camera's above horizon tilt capability is used.
Unitized SNC-ER580 pendant type, clear dome, with heater and blower
Unitized SNC-ER550 pendant type, clear dome, with heater and blower
Unitized SNC-ER520 pendant type, clear dome, with heater and blower
Unitized SNC-EP580 pendant type, clear dome, with heater and blower
Unitized SNC-EP550 pendant type, clear dome, with heater and blower
Unitized SNC-EP520 pendant type, clear dome, with heater and blower
81-IN6710 06152012
Advertisement
Table of Contents
Related Manuals for Sony UNI-ONEP520C2
Summary of Contents for Sony UNI-ONEP520C2
- Page 1 Installation and Operation Instructions for the following unitized outdoor camera models: UNI-ONER / EP SERIES Outdoor 24VAC Clear Dome UNI-ONER580C2 Unitized SNC-ER580 pendant type, clear dome, with heater and blower UNI-ONER550C2 Unitized SNC-ER550 pendant type, clear dome, with heater and blower UNI-ONER520C2 Unitized SNC-ER520 pendant type, clear dome, with heater and blower UNI-ONEP580C2...
-
Page 2: Important Safeguards
à presença de instruções importantes na literatura que acompanha o dispositivo. If technical support or service is needed, contact Sony at the following number: Questo simbolo del punto del exclamaton è inteso per avvertire l’utente alla presenza delle istruzioni importanti nella letteratura che accompagna l’apparecchio. -
Page 3: Electrical Specifications
Contents of Box Electrical Specifications UNI-ON Power 24VAC, Class 2 Only UNI-ON 26 Watts at 24 VAC (Heater and Blower) Camera: 25 Watts at 24VAC UNI-ON 26 vatios en 24VAC (calentador y soplador) Cámara: el 25 Watts a 24VAC UNI-ON 26 watts à... - Page 4 Mounting Preparation Securely attach pendant pipe or the UNI-WMB1 Wrap Teflon tape around the pipe threads (See block 9 when using UNI-WMB3). Pull wiring through pipe and position grommet as shown. to ensure a tight seal. • Con seguridad pipa pendiente de la fijación o el UNI-WMB1 (véase el bloque 9 para UNI-WMB3).
- Page 5 Loop the lanyard over the set screw to Make the appropriate wiring connections temporarily hold housing. from the dome to the pendant mount. • Loop el cordón sobre el tornillo de fijación para mantener • Hacer las conexiones de cableado de la cúpula de la temporalmente de la vivienda.
- Page 6 UNI-WMB3 If using external ¾” (27mm) conduit attach Install the wall mount bracket to a wall or appropriate hardware. adapter bracket. • Si usa conducto del ¾ (27mm) externo el” ata apropiado • Instale el soporte del montaje de la pared a la pared o soporte hardware.
- Page 7 Feed wiring into wall mount, UNDO lanyard and connect housing to wall complete connections. mount coupling. • Cableado de la alimentación en el montaje de la pared, • DESHAGA el acollador y conecte la cubierta con el acoplador conexiones completas. del montaje de la pared.
- Page 8 Camera 25 Watts 26 Watts COAX Wiring the dome can be completed by Secure the bolts with the provided referring to the diagram. Allen wrench. • Atar con alambre la bóveda puede ser terminada • Asegure los pernos con la llave Allen proporcionada. refiriendo al diagrama.
- Page 9 Before After Align the arrows on the outside of the dome Loop the lanyard around the tab inside the and lock. housing. • Alinee las flechas en el exterior de la bóveda y • Coloque el acollador alrededor de la lengüeta trábese.
-
Page 10: Materials Needed
How - to Clean a Dome Bubble To effectively clean your video surveillance dome bubble (acrylic or polycarbonate) from debris, follow these simple step-by-step instructions. Materials Needed • Clean, dry, pressurized air • Water • High quality soft paper towel •... -
Page 11: Replacement Parts List
Replacement Parts List UNI-ON Part Number Description SD0180W Pendent Coupling (White) RPFD2612 Housing Top Gasket RPFD709 Housing Top RP70FP7PB Connection PCB RPFD702 24Vac Heater RPFD060 Camera Bracket RPPKH6063 Spacers RPFD080 12Vdc Blower RPVL4101 Quick Release Bracket Camera RPFD703 Clamping Ring RP96GK2558 Dome Gasket RPFD7C... - Page 12 Available Mounting Accessories UNI-WMB3 UNI-WMB1 UNI-WMBB1 UNI-PBU1 UNI-RMB1 UNI-CMA1 UNI-PMA1 Aluminum Wall Mount Gooseneck Aluminum Existing Pole / Wall Mount Aluminum Corner Power Block Unit Parapet Mount Bracket Wall Mount Pole Mount Adaptor Mount Adaptor UNI-WMB3 UNI-WMB1 UNI-RMB1 Wall Mount Bracket Wall Mount RoofMount (Parapet) Mounting Accessories Needed:...
- Page 13 Warranty For warranty information on this and other Sony Security Systems Products, please visit: http://pro.sony.com/bbsccms/services/files/servicesprograms/SecurityWarranty.pdf...