Table of Contents
Advertisement
L i f e B o o k C S e r i e s – S e c t i o n T h r e e
Power Management
Your Fujitsu LifeBook has many options and features for
conserving battery power. Some of these features are
automatic and need no user intervention, such as those
for the internal modem. However, others depend on the
parameters you set to best suit your operating condi-
tions, such as those for the display brightness. Internal
power management for your LifeBook may be
controlled from settings made in your operating system,
pre-bundled power management application, or from
settings made in BIOS setup utility.
Besides the options available for conserving battery
power, there are also some things that you can do to
prevent your battery from running down as quickly.
For example, you can create an appropriate power saving
profile, put your LifeBook into Suspend mode when it
is not performing an operation, and you can limit the
use of high power devices. As with all mobile, battery
powered computers, there is a trade-off between
performance and power savings.
SUSPEND/RESUME BUTTON
When your LifeBook is active, the Suspend/Resume
button can be used to manually put your LifeBook
into Suspend mode. Push the Suspend/Resume button
when your LifeBook is active, but not actively accessing
anything, and immediately release the button. You will
hear two short beeps and your system will enter
Suspend mode.
If your LifeBook is suspended, pushing the Suspend/
Resume button will return your LifeBook to active
operation. You can tell whether or not your system
is in Suspend mode by looking at the Power indicator.
(See figure 2-8 on page 16) If the indicator is visible and
not flashing, your LifeBook is fully operational. If the
indicator is both visible and flashing, your LifeBook is in
Suspend mode. If the indicator is not visible at all, the
power is off or your LifeBook is in Hibernation (Save-to-
Disk) mode. (See Hibernation Mode)
SUSPEND MODE
Suspend or Standby mode in Windows 98 Second
Edition saves the contents of your LifeBook's system
memory during periods of inactivity by maintaining
power to critical parts. This mode will turn off the CPU,
the display, the hard drive, and all of the other internal
components except those necessary to maintain system
memory and allow for restarting. Your LifeBook can be
put in Suspend mode by:
Pressing the Suspend/Resume button when your
system is turned on.
Selecting Standby from the Windows Shut Down menu.
36
Timing out from lack of activity.
Allowing the battery to reach the Dead Battery
Warning condition.
Your LifeBook's system memory typically stores the
file(s) on which you are working, open application(s)
information, and any other data required to support the
operation(s) in progress. When you resume operation
from Suspend mode, your LifeBook will return to the
point where it left off. You must use the Suspend/Resume
button to resume operation, and there must be an
adequate power source available, or your LifeBook
will not resume.
C A U T I O N
If you are running your LifeBook on battery power,
be aware that the battery continues to discharge while
your LifeBook is in Suspend mode, though not as fast as
when fully operational.
HIBERNATION (SAVE-TO-DISK) FEATURE
The Hibernation (Save-to-Disk) feature saves the
contents of your LifeBook's system memory to the hard
drive as a part of the Suspend/Resume mode. You can
enable or disable this feature.
Enable or Disable the Hibernation Feature
The default settings are not enabled. To enable or disable
the Hibernation feature, follow these steps:
1. From the Start menu, select Settings, and then select
Control Panel.
2. From the Control Panel, select Power Options.
3. Select the Hibernation tab. Select the box to enable
or disable this feature.
Using the Hibernation Feature
1. From the Start menu, select Settings, then select
Control Panel.
2. From the Control Panel, select Power Options.
3. Select the Advanced tab. Select Hibernate from the
pull down menu for Power buttons.
P O I N T
Disabling the Suspend/Resume button prevents it
from being used to put your LifeBook in Suspend
or Hibernation (Save-to-Disk) mode. The resume func-
tion of the button cannot be disabled.
Advertisement
Chapters
Table of Contents
Troubleshooting
