Toshiba D-KVR20U Owner's Manual page 104

Dvd video recorder / video cassette recorder
Table of Contents

Advertisement

Symptom
The subtitle language cannot be
changed or turned off.
The angles cannot be changed.
Recording does not stop immediately
after you press [STOP C].
The disc tray does not open when you
press [OPEN/CLOSE A].
"Repairing" appears on the TV screen.
Repairing
In a case you intend to cancel the
repairing process.
D
V
Do you want to cancel a repairing
process ? When selecting "Yes",
the disc may not be usable.
D
Repairing
No image from HDMI connection.
There is no sound or the sound is
distorted.
There is no picture.
Picture noise appears.
V
The cassette tape does not play back.
C
The tape ejected after you press
R
[REC I].
The remote control does not function. • Check if a cassette tape is in this unit.
The motor rotates even when
playback / recording is stopped.
104 EN
104 EN
E9KGBUD_D-KVR20KU_EN.indd 104
E9KGBUD_D-KVR20KU_EN.indd 104
TROUBLESHOOTING
Remedy
• Multilingual subtitle are not recorded on the DVD-video.
• Multi-angles are not recorded on the DVD-video being played back.
• The angle-change operation is whenever possible as long as the disc
contains a multi-angle portion. Actual change will be performed when
the portion has come up.
• The DVD-video prohibits changing angles.
• Try changing the angle using the DVD-video's menu.
• It may take a few seconds for the unit to input disc data before
recording stops.
• It may take a few seconds for the disc tray to open after you have
recorded or edited a disc. This is because the unit is adding disc data to
the disc.
• If there is a power failure or unplugging during recording, finalizing,
formatting or editing (even after "Repairing" disappears), a repairing
process will begin automatically just after turning the unit on again.
It may take several minutes up to about several hours.
• If you intend to cancel the repairing process, press [A OPEN/CLOSE]
on the front panel, then select "Yes" and press [ENTER]. After that, press
[OPEN/CLOSE A] to take out the disc. The disc canceled during the
repairing process MAY NOT work.
Yes
No
• Check the HDMI connection. (Check the status of the HDMI related
indications.)
• Check whether the connected monitor device or other device supports
HDCP. (This unit will not output a video signal unless the other device
supports HDCP.)
• Check the setting of HDMI.
• Check whether the output format of this unit (HDMI FORMAT) matches
the supported input format of other connected device.
• If the unit is connected to the unauthorized display device with an
HDMI cable, the audio/video signal may not be output when playing
back a commercial DVD-video.
• The HDMI sound is not output when "HDMI Audio" is set to "OFF".
• Check the RCA audio cable connection. If you are using HDMI-DVI
conversion cable, you must connect the RCA audio cable, too.
• Check whether the output format of this unit (HDMI FORMAT) matches
the supported input format of other connected device.
• If you connect the cable to S-VIDEO OUT/ COMPONENT VIDEO OUT /
HDMI OUT jack, try connecting it to AUDIO / VIDEO OUT jack instead.
• Head cleaning for VCR may be necessary. Refer to "Auto Head Cleaning"
(page 5).
• Adjust tracking control for better picture by pressing [TRACKING
while you are playing back a cassette tape.
• No cassette tape is inserted.
• Make sure the cassette tape has an erase-protection tab when you
record to a cassette tape. If needed, cover the hole with cellophane
tape.
• The motor may rotate for the duration of approximately 5 minutes for
efficient operation. This is not a malfunction.
/
]
2008/05/27 16:11:52
2008/05/27 16:11:52

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

D-kvr20ku

Table of Contents