Adjusting The Subwoofer Level; Lowering Subwoofer Level Temporarily; Setting The Subwoofer Phase; Adjusting The Time Correction (Tcr) - Alpine INE-W940 Owner's Manual

Adjusting the Subwoofer Level

You can set the Subwoofer level when a Subwoofer is connected.
Setting item: SubW. LEVEL
Setting contents: 0 to 15 (Initial setting: 0)
• If the Subwoofer setting is "Off, " the setting cannot be set.

Lowering Subwoofer Level Temporarily

Touch [Sub W. LEVEL 0] to lower the Subwoofer level
to Level 0.
• To return to the previous Subwoofer level, touch [Sub W. LEVEL 0]
again.

Setting the Subwoofer Phase

The subwoofer output phase is toggled Subwoofer Normal (0°) or
Subwoofer Reverse (180°).
Setting item: SubW. Phase
Setting contents: 0° / 180° (Initial setting: 0°)
• If the Subwoofer setting is "Off, " the setting cannot be set.

Adjusting the Time Correction (TCR)

[TCR] is selected on the Sound setup menu in step 3. Refer to "Sound
Setup Operation" (page 34).
Before performing the following procedures, refer to "About Time
Correction" (page 38).
Setting item: Time Correction
1
Touch [ms] or [cm] to select mode for making
adjustments.
Each time you touch, the onscreen button and correction
mode changes.
ms: Adjust time.
cm: Adjust listening position and distance from each speaker.
2
Touch [ ] or [ ] for each speaker to adjust the
time or distance.
0.0msec to 9.9msec (0.1msec/step)
0.0cm to 336.6cm (3.4cm/step)
All speaker setting values are adjustable in the range of 15ms or
510cm.
36
-EN
Correction mode
3
To store the adjusted setting value, touch and hold
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
• Touch [Flat] to set all values to 0.0.
• If the Rear Speaker setting is "Off," the Rear Speaker setting cannot
be edited (Refer to page 38).
• If the Subwoofer setting is "Off," the Subwoofer setting cannot be
edited (Refer to page 38).
Calling the Time Correction Value
Calling the pre-set time correction value.
Touch [Preset1], [Preset2], or [Preset3] on the time
correction screen.
The setting stored in the Preset will be recalled.
Adjusting the Crossover Settings (X-
OVER)
[X-OVER] is selected on the Sound setup menu in step 3. Refer to
"Sound Setup Operation" (page 34).
Before performing the following procedures, refer to "About the
Crossover" (page 39).
Setting item: X-OVER
1
Touch [Channel] to select the channel.
Each time you touch, the channel switches.
• The channel being adjusted is displayed in red.
Front HPF Rear HPF
2
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch [ ] or [ ] of "Freq.," then select the cut-off
frequency.
Setting contents: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) /
100 / 125 / 160 / 200 Hz
Adjusting the Slope
Touch [ ] or [ ] of "Slope," then adjust the HPF or LPF
slope.
Setting contents: 0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct
Adjusting the Level
Touch [ ] or [ ] of "Level," then adjust the HPF or LPF
level.
Setting contents: -12 to 0 dB (Initial setting: 0)
3
Repeat steps 1 to 2 to make adjustment to the other
channels.
Subw. LPF