Page 1
THS 812 Digitální satelitní přijímač pro vysoká rozlišení obrazu Look, Listen & Live Návod k obsluze Používateľská príručka www.thomsonstb.net User manual...
Page 4
Licenses ANY USE OF THIS PRODUCT IN ANY MANNER OTHER THAN PERSONAL USE THAT COMPLIES WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2 PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPeGLA,LLc, 6312 S.
1.0inTRoDUcTion 1.1safetyinstructions DonoTinsTALLYoURReceiveR: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots. DonoTeXPoseTheReceiveRoRiTsAccessoRies: To direct sunlight or any other equipment that generates heat; to rain or intense moisture; to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc.
It is advised not to store important information on USB storage devices used with the receiver. Always make backups of data on your USB storage device before using it with this receiver. THOMSON will not take responsibility for any loss of information or circumstances caused by loss of information.
7. hDMi To connect to the HDMI input of your TV set using a good quality HDMI cable 8. Powerswitch To switch ON or OFF power of your receiver 9. DcPoWeR To connect to the original included main power adapter (Input 110 ~240 V 50~60 Hz/ Output 12 V DC 2.4RemotecontrolUnit Fig.
The batteries must not be recharged, disassembled, electrically short-circuited, be mixed or noTe: used with other types of batteries. 2.6UsingtheRemotecontrol Fig. 5 To use the remote control, point it towards the front of the digital receiver. The remote control has a range of up to 5 metres from the receiver at an angle of up to approx. +-30 degrees. The remote control will not operate if its path is blocked.
4.0sTARTinGUPfoRThefiRsTTiMe Ensure that your satellite signal is of good quality and that all connections are properly setup. In case of difficulties or questions, please ask your local dealer for assistance. It is recommended to follow the First Time Installation step by step. It will guide you through the basic installation and channel searching process.
5.0QUickGUiDeToUsinGYoURReceiveR We at THOMSON understand that you can’t wait to enjoy your new HD receiver. The following quick guide will make you familiar with the basic operation of this device. We do, however, advice you to read the full manual to get the best performance from your THOMSON HD receiver.
The volume can be adjusted with the v+/v- buttons. This is also possible in ALL menus which present TV picture in background. In viewing mode you can also use the buttons. Additionally you can ! your receiver in ALL menus which present TV picture in background. The PG+/PG- enable you to scroll page wise in all list modes to make your channel or other selection as comfortable as possible.
6.3selectionofaudiolanguage Some channels support a choice of different audio formats and/or languages. To select another audio stream, press AUDio in the viewing mode. A list with the available audio languages will be displayed. Use to select the desired audio language and confirm with ok. It is also possible to select another audio mode with the buttons.
7.1installation This menu allows you to change satellite settings and to search for channels. Further you can adjust important settings for your receiver. It consists of the following sub-menus: Antenna Setup, Channel Search, System Settings, Parental Lock and Factory Reset. Choose the desired sub menu with and press ok to advance.
Page 16
Channel Type: TV & Radio will scan for TV and Radio channels, TV for TV channels only and Radio for radio channels only. After these settings are adjusted for the desired scan process, move to Scan selected satellite with and then select the search method via You can select between following procedures: Scan selected satellite: Will scan the selected satellite under above given circumstances.
Page 17
Once all settings are made, press eXiT/soRTie to leave the System Settings menu. When returning to the viewing mode the receiver informs with a message that it saves your settings. 7.1.3.1hDMi In this submenu you can set following parameters: TV Ratio: 16:9 or 4:3, depending on the kind of your TV set. Conversion: Letterbox, PanScan or Combined, to choose the preferred picture format.
After all settings are adjusted following to your preference, choose Save with and press ok. The receiver returns to the menu. 7.1.4ParentalLock This menu enables you to define and edit your PIN code, set Installation or Parental Lock. and press ok to list the possibilities up or use Choose the desired setting with change the value of the highlighted setting.
7.2.5oTAsoftwareUpdate The OTA (Over the Air) function allows you to search for software updates available on ASTRA 23.5 satellite. Please ask your local THOMSON dealer or visit our website www.thomsonstb.net for information. After pressing ok on OTA Software Update to execute your receiver will start looking for new software.
Page 20
Irdeto smart card, in case it is inserted. The following menus are available: Irdeto Status, Mail and Maturity Rating. 7.3.1irdetostatus This menu gives access to following submenus which can be opened to find detailed information about these items: Smart Card Status, EMM Status, ECM Status, Loader Status, Product List Status.
7.4channelManager Within this menu you can manage channels and configure favourites, define an auto channel update or from a connected USB storage device. The menu consists of the following sub- menus: TV Channels, Radio Channels, Auto Channel Update and TV Programme Guide. Choose the desired sub menu with and press ok to advance.
7.4.3AutochannelUpdate In this menu you can perform an automatic channel update on Astra 23.5 satellite. You can setup a mode and desired time for this. It will enable you to update the complete channel database of your receiver or save you the time for a full channel scan. to select ON as the default setting is OFF.
If the receiver does not work properly after checking it, please contact your local Serviceline or THOMSON dealer. Alternatively you can send a support mail via our website: www.thomsonstb.net. NEVER open or disassemble your receiver.
Page 24
symptom cause Remedy No picture The receiver can’t receive the Check the antenna cable, replace signal. the cable, or connect the cable to the receiver tightly. Incorrect values of some Set the values of tuner parameters tuner parameters. correctly in menu Installation – Antenna Setup/Channel Search.
Need help?
Do you have a question about the THS812 and is the answer not in the manual?
Questions and answers