Advertisement
LSR6325P-1 Linear Spatial Reference Bi-Amplified Studio Monitor
Specifications:
System:
Frequency Response (+1, -2 dB): 70 Hz - 20 kHz
Enclosure resonance frequency: 55 Hz
Low Frequency Extension: User controls set to default
-3 dB: 65 Hz
-6 dB: 56 Hz
-10 dB: 48 Hz
Low - High Frequency Crossover: 2.3 kHz
4th-order Electroacoustic Linkwitz-Riley
Distortion, 96 dB SPL, 1 m:
Mid-High Frequency (150 Hz - 20 kHz):
2nd Harmonic: <0.5%
3rd Harmonic: <0.5%
Low Frequency (<150 Hz):
2nd Harmonic: <2%
3rd Harmonic: <3%
Maximum SPL (90 Hz - 20 kHz): >106 dB SPL / 1m
Maximum Peak SPL (90 Hz - 20 kHz): >109 dB SPL / 1m
Signal Input: XLR, Balanced
RCA, unbalanced
Postitive voltage applied to XLR Pin 2 (RCA tip)
produces outward woofer motion.
Calibrated Input Sensitivity:
XLR, +4 dBu: 96 dB SPL / 1 m
RCA, -10 dBV: 96 dB SPL / 1 m
AC Input Voltage: 115 /230 VAC, 50/60 Hz (User Selectable)
AC Input Voltage Operating Range: +/- 15%
AC Input Connector: IEC
Long-Term Maximum System Power: 110 watts (IEC265-5)
Self Generated Noise Level: <10 dBA / 1 m
User Controls:
High Frequency Control (3 kHz - 20 kHz): +1.5 dB, 0 dB, -1.5 dB
Workstation Boundry Compensation: Active or Bypass
Low Frequency Acoustic Alignment: 36 dB/Octave Butterworth bi-pass at 40 Hz
36 dB/Octave Bessel hi-pass at 80 Hz
(For use with Subwoofer)
Variable Input Attenuation: 0 - 26 dB
Transducers:
Low Frequency Diameter: 134 mm (5.25 in)
Voice Coil: 38 mm (1.5 in)
Magnet Type: Ferrite with Integral Shielding
Cone Type: Tempered Paper with Butyl Rubber Compliance
Nominal Impedance: 8 ohm
High Frequency Diameter: 25 mm (1 in) diaphragm
Voice Coil: 25 mm (1 in)
Magnet Type: Ferrite with Integral Shielding
Diaphragm Type: Damped Titanium Composite
Other Features: Elliptical Oblate Spheroidal Waveguide
Nominal Impedance: 4 ohms
Amplifiers:
Low Frequency:
Topology: Bridged Class A-B Monolithic
Sine Wave Power Rating: 100 watts (<0.1% THD into rated impedance)
THD+N, 1/2 Power: <0.05%
High Frequency:
Topology: Class A-B, Monolithic
Sine Wave Power Rating: 50 watts (<0.1% THD into rated impedance)
THD + N, 1/2 Power: <0.05%
Physical:
Finish: Black Powdercoat
Grille: Perforated Steel
Enclosure Volume (net): 6.5 liter (0.2 cu. ft.)
Low Frequency Vent: Dual Linear Dynamic Aperture
Baffle Construction: Diecast Aluminum
Cabinet Construction: Diecast Aluminum
Mounting: 4 threaded mounting points conforming to industry standard
square pattern, 127 x 70 mm (5 x 2.75 in) 107.9 mm x
50.8 mm (4.25 x 2 in) center to center. M6 metric threads.
Net Weight: 7.7 kg (17 lb)
Dimensions (WxHxD): 17.3 x 26.9 x 24.1 cm (6.8 x 10.6 x 9.5 in)
Mounting Specifications:
The LSR6325P-1 has built-in mounting points for use
with industry-standard mounting hardware.
The mounting points are located on the rear panel of
the speaker system. The four threaded holes accept a
1/4" diameter machine screw with a pitch of 20 threads
per-inch. The length of the screw should be a total of
3/8th inch plus the thickness of the mounting bracket.
Hole Pattern:
107.9 mm
(4.25 in)
+
+
Caution: Unsafe mounting or overhead suspension of any heavy load can result in
serious injury and equipment damage. Mounting of speakers should be done by quali-
fied persons in accordance with all applicable local safety and construction standards.
Be certain to follow the instructions provided by the manufacturer of the mounting
bracket, be certain that it is capable of supporting the weight of the speaker to be
mounted.
Notes:
All measurements unless otherwise stated are made anechoically in a 4π environment
at 2 meters and are referenced to 1 meter by the inverse square law.
The reference measurement microphone position is located perpendicular to the cen-
terline of the low and high frequency transducers, at the point 70 mm (2.7 in) above
the center of the woofer.
Acoustic loading provided by the listening room increases Maximum SPL capabilities
and Low Frequency Bass Extension as compared to stated anechoic values.
Distortion measurements are performed with the input voltage necessary to produce
the stated "A" weighted SPL level at the stated measurement distance. Distortion fig-
ures refer to the maximum distortion measured in any 1/10th octave wide band in the
stated frequency range.
JBL continually engages in research related to produce improvement. New materials,
production methods, and design refinements are introduced into existing products
without notice as a routine expression of that philosophy. For this reason, any current
JBL product may differ in some respect from its published description, but will always
equal or exceed the original design specifications unless otherwise stated.
+
50.8 mm
(2 in)
+
Advertisement
