connection
USINGTHEVOICE+FUNCTION
•
The Voice+ function works only in Player mode. ➥ page 18
•
When you want to play back or record a tape-recorded movie on other AV device,
you can transfer the voice sound incoming from the internal microphone of your
camcorder, instead of the audio signals on a prerecorded tape.
1. Connect the provided Audio/Video cable to the AV jack of the camcorder.
2. Connect the other end of the cable
to the VCR/DVD Recorder/TV by
matching the colours of the terminals.
3. Set the Select switch to TAPE.
(VP-D385( i ) only).
4. Press the MODE button to set Player
(
).
5. Insert the tape you wish to play back in
this camcorder.
6. Press the Recordingstart/stop button
on a point where you want during the
playback.
•
Voice+ (
) indicator is displayed
on the screen and "VOICE+" will
flicker on the screen for a while.
•
Sound incoming from the internal
microphone will be transferred to
the connected AV device, instead of
the pre-recorded sound on the tape.
7. To cancel the function, press the Recordingstart/stop button again.
•
Voice+ is available only when the Audio/Video cable
is connected. If a different cable (DV or USB cable
(VP-D385( i ) only)) is connected, Voice+ function may
not operate properly.
•
If you move the Joystick(///) when you
operate Voice+ function, Voice+ function will be
deactivated.
•
During the Voice+ process, the MENU and PHOTO
button functions do not work.
•
The Voice+ function does not affect the original sound
on the recorded tape.
•
Sound is transferred from the internal microphone
on this camcorder to the connected AV device, when
using the Voice+ function.
So make sure that this microphone is not blocked.
•
Adjust the sound volume on the connected external
device. (TV, etc.)
•
Howling may occur near the speaker of an external
device, please keep the camcorder at a distance from
the external device.
•
Before connecting, make sure that the volume on the
external device is turned down. Forgetting this may
cause howling from the external device's speakers.
72_ English
连接
使用 VOICE+ 功能
•
•
TV
VCR
Signalflow
SP
MIX[1+2]
12:00 1.JAN.2008
SP
MIX[1+2]
Voice+
12:00 1.JAN.2008
仅可在 Player( 播放 ) 模式下使用 Voice+ 功能。➥ 第 18 页
当您想要在其他 AV 设备上进行播放或录制一盘影音录像带时,您可以
通过摄录机的内置麦克风录制声音代替磁带上之前被录制的音频信号。
Camcorder
AV
DV
AVJack
MODE
POWER
CHG
Audio/VideoCable
7. 若要退出此功能,请再次按下录制开始 / 停止按钮。
0:00:20:23
60min
•
Voice+ 功能仅支持在已经连接音频 / 视频线的
16BIt
S
时候使用。如果连接不同的电缆
(DV 线或 USB 数据线 ( 仅限 VP-D385( i )),
Voice+ 功能可能不会正常运行。
•
当使用 Voice+ 功能时如果您拨动操纵杆
AV In
(///),Voice+ 功能将被取消。
•
在使用 Voice+ 功能时,MENU 和 PHOTO 按钮
不能使用。
•
0:00:20:23
使用 Voice+ 功能不会影响到已经录制在磁带上
60min
原始声音的效果。
•
16Bit
当使用 Voice+ 功能时,声音通过摄录机的内置麦克
S
风传送至被连接的 AV 设备上。所以,请确保摄录机
的内置麦克风没有被任何物体遮挡。
•
请调节被连接的外部设备的音量。( 电视机,等 )
•
AV In
距离较近的外部设备的扬声器会传出刺耳的噪音,
请将摄录机与外部设备保持一定的距离。
•
在连接之前,请确保被连接的外部设备音量已
经被调到很低。否则,外部设备的扬声器可能
传出刺耳的噪声。
1. 使用提供的音频 / 视频电缆连接
至摄录机上的 AV 端口。
2. 将电缆的另一头与 VCR/DVD 录
像机 / 电视机上与之匹配颜色的
接口相连。
3. 切换存储介质为 TAPE。
( 仅限 VP-D385( i ))
4. 按下 MODE 按钮设置为
Player( 播放 ) 模式 (
)。
5. 在摄录机内插入您想要播放的磁
带。
6. 播放的过程中,在您想要进行编
辑的点按下录制开始 / 停止按钮。
•
显示 Voice+ 指示图标
(
)并且在屏幕上将闪烁
"VOICE+" 提示信息。
•
通过连接的电缆声音将由内置
麦克风传入连接的 AV 设备,
代替之前磁带上录制的声音。
中文 _72