Parts You Will Need*
(Not Included)
1
• Drain Hose Clamp, 1
Diameter
/
”
4
3
• Elbow, 90° with a
/
” National Pipe Thread
8
• Conduit Connector
• Wire Nuts, two (2) for 12-14 gauge wire
*
If required:
Available at:
• “Y” Branch Tailpiece and
Plumbing Supply Store
Connector Kit (See Step 4)
• Air Gap Kit (See Step 4)
Plumbing Supply Store
• Fasteners for floor
Hardware Store
anchoring (See Step 9)
Electric Shock Hazard
Disconnect electrical power at the fuse box or
circuit breaker box before beginning installation.
Failure to follow this warning could result in death
or serious injury.
• Examine dishwasher and locate connections. See Step 4.
• Locate dishwasher where there is easy access to drain,
water, and electrical lines. The best location is on either side
of the kitchen sink for access to existing plumbing and ease
in loading dishes. See Step 4.
• Electrical, water, and drain connections are not the same for
all age, brands, or models of dishwashers. Check the
location and length of home utilities. See Step 4.
• A 15-20 amp, grounded, 120 volt AC only, electrical supply is
required. See Steps 4 and 8.
• If dishwasher drain hose will be connected to a food
disposer for the first time, knock out plug located inside
disposer inlet. See Steps 4 and 6.
• Kinked water or drain hoses can cause problems. See Step
6.
• Dishwashers need to be connected to a hot water supply
with enough water pressure to insure an adequate fill.
See Steps 4 and 7.
• Each home installation differs. You will need additional
parts listed above to complete your installation.
See Steps 4 and 7.
• Flush water line prior to making the final connection to
prevent clogging of dishwasher’s filter screen. See Step 7.
• The dishwasher will look, sound, and perform best when
properly leveled. See Step 5. (NOTE: If levelers are
removed during installation, make sure the floor is flat and
free of any obstruction.)
• Anchor the dishwasher. See Step 9.
2
Installation Preparation
1.
Remove two (2) screws at front of the kickplate assembly using
a #2 Phillips screw driver.
2.
Tilt and pull forward to remove. See Figure 1.
NOTE: It is not necessary to remove the outer door for installation.
However, you might find it more convenient to do so. You
can find directions for removing door in Step 10.
Kickplate Assembly
Kickplate Assembly
Kickplate Assembly
Kickplate Assembly
Kickplate Assembly
Adjustable Toeplate
Adjustable Toeplate
Adjustable Toeplate
Adjustable Toeplate
Adjustable Toeplate
Water Inlet
Water Inlet
Water Inlet
Water Inlet
Water Inlet
Bottom Screws
Bottom Screws
Bottom Screws
Bottom Screws
Bottom Screws
Valve
Valve
Valve
Valve
Valve
Kickplate
Kickplate
Kickplate
Kickplate
Kickplate
(Insulation available
(Insulation available
(Insulation available
(Insulation available
(Insulation available
Figure 1
Figure 1
Figure 1
Figure 1
Figure 1
some models)
some models)
some models)
some models)
some models)
3. Locate water inlet valve behind kickplate on bottom left
3
underside of unit. The valve has a
/
” NPT female fitting.
8
4. Wrap 90° elbow (not included) with pipe thread tape (or apply
joint compound) and thread it into water inlet valve.
5. Tighten elbow with a wrench, leaving elbow pointing toward
rear of unit. To prevent bending of bracket or breaking of valve,
avoid overtightening.
Cabinet Preparation:
As a precaution, it is recommended, but not required that the
cabinets enclosing all sides of the dishwasher (including the
underside of the countertop) be sealed with an oil based paint
or moisture-proof polyurethane to prevent possible steam/
moisture damage.