Exhaust Direction; Manufactured Or Mobile Home Installation - Frigidaire 137111800B Installation Instructions Manual

Frigidaire gas & electric dryer installation instructions
Table of Contents

Advertisement

Available languages

Available languages

Exhaust system requirements, continued
In installations where the exhaust system is not described in
the charts, the following method must be used to determine
if the exhaust system is acceptable:
1. Connect an inclined or digital manometer between the
dryer and the point the exhaust connects to the dryer.
2. Set the dryer timer and temperature to air fl uff (cool
down) and start the dryer.
3. Read the measurement on the manometer.
4. The system back pressure MUST NOT be higher than
0.75 inches of water column. If the system back pressure
is less than 0.75 inches of water column, the system is
acceptable. If the manometer reading is higher than .075
inches of water column, the system is too restrictive and
the installation is unacceptable.
Although vertical orientation of the exhaust system is
acceptable, certain extenuating circumstances could affect
the performance of the dryer:
Only the rigid metal duct work should be used.
Venting vertically through a roof may expose the exhaust
system to down drafts causing an increase in vent
restriction.
Running the exhaust system through an uninsulated area
may cause condensation and faster accumulation of lint.
Compression or crimping of the exhaust system will cause
an increase in vent restriction.
The exhaust system should be inspected and cleaned a
minimum of every 18 months with normal usage. The
more the dryer is used, the more often you should check
the exhaust system and vent hood for proper operation.

Manufactured or mobile home installation

1.
Installation MUST conform to current Manufactured
Home Construction & Safety Standard, Title 24 CFR, Part
32-80 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD Part 280) or
Standard CAN/CSAZ240 MH.
2.
Dryer MUST be exhausted outside (outdoors, not beneath
the mobile home) using metal ducting that will not support
combustion. Metal ducting must be 4 inches (10.16 cm) in
diameter with no obstructions. Rigid metal duct is preferred.
3.
If dryer is exhausted through the fl oor and area beneath
the mobile home is enclosed, the exhaust system MUST

Exhaust direction

Directional exhausting can be accomplished by installing a
quick-turn 90° dryer vent elbow directly to exhaust outlet of
dryer. Dryer vent elbows are available through your local parts
distributor or hardware store.
See also CLEARANCE REQUIREMENTS on the next page.
Use of 90° quick-turn elbow required to meet mini-
mum installation depth of free-standing dryer:
Straight back venting allows for 0" (0 cm) installation.
Venting right with 90° elbow allows for 0.75" (2 cm)
installation.
Venting downward with 90° elbow allows for 0.75" (2 cm)
installation.
Venting left with short, straight adapter and 90° elbow
allows for 3.75" (9.5 cm) installation.
Venting upward with short, straight adapter and 90°
elbow allows for 4" (10.5 cm) installation.
terminate outside the enclosure with the termination
securely fastened to the mobile home structure.
4.
Refer to previous sections in this guide for other important
exhaust venting system requirements.
5.
When installing a gas dryer into a mobile home, a
provision must be made for outside make up air. This
provision is to be not less than twice the area of the dryer
exhaust outlet.
6.
Installer MUST anchor this (1) dryer or (2) dryer mounted
on pedestal to the fl oor with approved Mobile Home
Installation Kit - P/N 137067200.
6

Advertisement

Table of Contents
loading

This manual is also suitable for:

Gceq2170ksGlgq2170keGlgq2170ks

Table of Contents

Save PDF