Installing Your Multifunction to Your Network for the First Time PIXMA MP990 I PIXMA MP640 / PIXMA MP560 Macintosh OS Preparing to Connect My Multifunction to My Network .............. 2 Network Requirements ......................2 Important Information You Need Before Adding Your Multifunction ........3 Adding Your Multifunction to Your Network ................
Preparing to Connect My Multifunction to My Network Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network. Notes on Network Connection •...
An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported. Be sure to prepare an access point Important Information You Need Before Adding Your Multifunction The following information is required to connect to your access point or router. •...
Page 4
Step Two Select Device settings, then press the OK button. Step Three Select Yes, then press the OK button. When wireless connection is enabled, the V\Ii-Fi lamp** (B) lights blue. **Wi-Fi lamp location varies according to model. Step Four Select Easy settings, and then press the OK button. Step Five Select the access point name you wrote down, then press the OK button.
Page 5
NOTE If you are living in an apartment, nearby access points in use may be detected. Step Six When one of the following screens is displayed, enter the network key you wrote down, then press the OK button. If the following screen is not displayed, go to Step Eight. Use the Easy-Scroll Wheel to select the character Use the ...
Note: If Failed to connect to the access point appears, press the OK button, make sure that the network key is correct, then enter it again. If a connection still cannot be established, refer to the printed manual: Network Setup Troubleshooting. Confirm Connection Status Step One Press the HOME*** button (A), select Settings using the Easy-Scroll Wheel (B), and then press...
Page 7
Step Four Select Confirm LAN settings, then press the OK button. Step Five Select Wireless LAN setting list, then press the OK button. Make sure that Connection is set to Active, and then press the HOME button. It may take a while before the connection is complete In this case, press the Back* button (C) and wait for about a minute, then display the Wireless LAN setting list screen again.
Step One Go to the Canon Canada Support Home Page Click here to go to the Canon Canada Support Home Page Step Two Select Consumer & Home Office in the Product Type menu dropdown, All-In-One Printer in the Product Family, PIXMA MP Series in the Product Series and click on the Drivers &...
Page 9
• If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network. If such a warning message appears, set the security software to always allow access.
Installing The Driver Step One Double-click the Setup icon Step Two If the following message appears, click Open Page 10...
Page 11
Step Three Enter your administrator name and password. Click OK. Step Four Select the place of residence and click Next. Page 11...
Page 12
Step Five Click Easy Install. Step Six Click Install. Page 12...
Page 13
Step Seven Select Use the printer on network, then click Next. Page 13...
Page 14
Step Eight Read the License Agreement screen carefully and click Yes. Step Nine When the Printer Detection screen appears, click Next. Page 14...
Page 15
Click Exit on the installation complete screen, then start again from step 1 and be sure to select Use the printer on network in step 7. Step Ten On the Canon IJ Network Tool screen, select MPxxx series in Printers, then click Next ('xxx' refers to printer model number) NOTE: •...
Page 16
Step Eleven When the Connection Performance Measurement screen appears, click Next. Confirm the measurement results, then click Finish. Ensure that is displayed in Connection performance between the printer and the access point. NOTE: • You can cancel measuring by clicking Cancel You also examine the detailed status of the communication link after setup.
This section describes how to register the machine on a Macintosh computer. Step One When the Register Printer and Scanner screen appears, click Register Printer. Step Two Select Canon xxxx series ('xxxx' refers to the model) and click Add. Page 17...
Page 18
MAC address Step Three When the Register Printer and Scanner screen appears, click Register Scanner. Step Four Select Canon xxxx series or xxxx series( 'xxxx' refers to the model) on the Scan-from PC Settings screen, then click OK. Page 18...
Page 19
Step Five When the Register Printer and Scanner screen appears, click Next. Step Six Click Exit. Page 19...